Mitsubishi Electronics XL21, XL50 installation manual Condenser lens adjustment for Single

Page 81

2.2. Condenser lens adjustment (for Single)

When brightness is low after the lamp replacement, the brightness may increase if you adjust the position of the condenser lens.

You don’t have to adjust it at initial setting since the position has been adjusted optimally with a built-in lamp at factory.

[Procedure]

1.After turning on the main power, wait until the brightness becomes stable (about three minutes).

2.To access the optical unit, open the screen (chapter 1.2.7.1, on page 21) in Front or open the rear panel in Rear.

3.Set WHITE BOOST OFF (chapter 1.5.3.9, on page 50).

4.Display an internal test pattern except “full-bit white” by [TEST] button.

5.Press and hold [DISPLAY] button in advanced mode to display the status information. The luminous sensor value (L.SENSOR) is indicated in the lowest line.

Luminous sensor value

! ANALOG

ID01

F/W VER

P01.50A

H/W VER

12.19

SET TIMER

99999H

MASTER

 

L.SENSOR

125

 

 

6.Loosen the adjustment screw on the optical unit with an Allen wrench (2.5mm).

7.Move the screw position along the flute to maximize the luminous sensor value and fix it.

Note: Do not tighten it with an excessive torque

(suggested torque: 0.38Nm+/-0.03). Fix it not to move off the position.

8.Put back the WHITE BOOST setting.

9.Put back the screen (chapter 1.2.7.2, on page 22) or the rear panel.

Adjustment screw (hexagon socket head)

REV 2.4

81

Page 80 Page 82
Image 81
Page 80 Page 82
Contents Set-up and Installation Manual Table of Contents REV 118 Set-up and installation Overview FlowchartProduct lineup Cube installation Safety precautionPreparation Input board installation optional Color wheel unlocking Unlocking for XL21Lamp cushion removing for Changer PH50 Cube stacking for Rear Assembling the base stands and cubesScreen gap adjustment Fixing to the wall and floor Tape peeling off for Cube stacking for FrontScreen detaching For 67 , 50 Changer VentilationFor 50 Single External AC fan attaching occasional Assembling base stands and cubes As needed, you can adjust the screen gaps Adjustment Screen opening Screen open/close for FrontScreen closing Control signal connection ConnectingImage signal connection Case of daisy chainInternal cabling for Front For other than daisy chainMenu operation Control button list Initial set upOperation mode Remote ID Basic menu operationDipswitch setting Picture outline adjustmentDisplaying internal test pattern Attaching Axis adjustmentFront Close the screen .2.7.2, on Detaching AdjustmentPosition Keystone Tilt Zoom Correct the horizontal keystone distortion Mirror adjustment 50 XL21 XL50 Rear and PH50 System set up Lamp Power System memory settingLamp Mode for XL21 This adjustment is normally unnecessary Terminate This adjustment is normally unnecessaryOverlap for the input board Start MemoryImage Flip This adjustment is normally unnecessary Baud RateSystem Sync Indication This adjustment is normally unnecessary Extended ID Auto Power onResolution for PH50 This adjustment is normally unnecessary Direction This adjustment is normally unnecessaryCable Length for PH50 and XL50 Changer Lamp Change forBlack Level This adjustment is not necessary Color balance adjustmentREV Gradation White BalanceSensor Target ColorColor Matrixuser Image set upADV.DARK This adjustment is normally unnecessary ADV.COL This adjustment is normally unnecessaryGamma This adjustment is normally unnecessary Dither This adjustment is normally unnecessaryWhite Boost This adjustment is normally unnecessary Input memory setting for the main input Automatic input signal scanningInput port selecting 3.1. H.POSITION, V.POSITION Signal adjustmentFine for Analog input AMP Gain for Analog inputSignal Select Signal Select for XL21Clamp START=0, Clamp WIDTH=0. Procedure Brightness ContrastColor Matrix ApertureInput memory calling/deleting Input memory savingExpansion setting Input memory setting for the input boardFine for S.ANALOG input 4.1. H.POSITION, V.POSITIONAMP. Gain for S.ANALOG input Scanning Value is automatically set in automatic input signalClamp START=0, Clamp WIDTH=0. Procedure With VC-B20KA Brightness ASPECT-RATIO VCR Mode for Composite or Y/C input with VC-B20KVColor for Composite or Y/C input Tint for Composite or Y/C inputInput memory saving Display memory setting for the input board Input Memory2. H.DISPLAY POS, V.DISPLAY POS Digital OUT Screen ModeDisplay memory calling/deleting Display memory savingSetting as daisy chain connection for the input board Display POS /1 Safety precautions Regular maintenance 2.1. Lamp replacementFor Single ProcedureTighten the two lamp fixing screws For Changer Open the lamp cover Close the lamp cover Partition door Auto-lamp changing function for Changer Action in lamp failure burnout or explosionAction in brightness deterioration Lamp position auto calibration Manual lamp swapLamp will Exchange Soon Condenser lens adjustment for Single Focus adjustment Cleaning procedure CleaningScreen front surface CabinetFilter Time Filter ResetFor delivery Axis adjuster fixingColor wheel locking for XL21 Lamp cushion inserting forScreen-holding arm locking for 67 Front FrontMenu trees Function MemoriesInput memory Common itemsAdditional items When Analog or S.ANALOG is selected Additional items When S.DIGITAL is selectedDisplay memory Items within parentheses are initial values System memoryMemory list display Test pattern list Control panelLED display LED display list Terminal functions RS-232C terminalControl terminal Available input signal list RGB signal Ycbcr Ypbpr component video signal Accessory Motorized adjustment tool, S-AXL50E specificationApplicable product Outline drawingTerminal for firmware upgrading/slide switch Terminals OutlineRotary dial Recovery procedure from error Reset buttonTrouble shooting LEDAdjustment software, Wallaby 4.1. General InstallationInitial set-up Automatic panel ID setting System configuration settingManual panel ID setting Serial port settingSerial port opening AdjustmentTurning on Picture mute offMaintenance Service tab for system memoryOptimize gain function Auto CSC functionInstallation Misc Function Input tab for input memory 107 Additional items When Composite or Y/C is selected Display tab for display memory Information tab Memory tabMemory copy Memory backup Cube data savingData sending to cubes Main window Power and MutePanel selection area Serial PortMenu bar Send Parameter Edit menu Read ParameterCopy Parameter Paste ParameterOther Wall Config… System Config menu By n 1x1, 2x2, 3x3 orCube ID Setting Auto IDSpecial menu Protect Setting Port SettingSerial Port menu Log… OpenAbout trademarks Description Revision date Revision history

XL21, XL50 specifications

Mitsubishi Electronics has consistently set benchmarks in the realm of display technologies, and their XL50 and XL21 projector series showcases this commitment to excellence. These models are meticulously designed to cater to a variety of professional environments, making them indispensable tools for businesses, education, and large venues.

The flagship XL50 projectors offer superior brightness with an impressive maximum output, ensuring vivid images even in well-lit rooms. With a native resolution that supports Full HD content, users can expect crystal-clear presentations that captivate audiences. The XL50 also incorporates advanced color reproduction technologies, which provide a wide color gamut for dynamic visual experiences. The projectors utilize Mitsubishi’s proprietary 3LCD technology, which enhances color accuracy and brightness, allowing for incredible detail and realism in every projected image.

In contrast, the XL21 models are tailored for users seeking a balance between affordability and performance. While slightly less powerful than the XL50, these projectors still deliver remarkable brightness, making them suitable for small to medium-sized meeting rooms and classrooms. The XL21 also features a compact and lightweight design, facilitating easy transportation and setup. With a focus on user-friendly operation, both models offer intuitive interfaces and connectivity options, including HDMI ports, VGA connections, and wireless capabilities, enabling seamless integration with other devices.

In terms of advanced features, both the XL50 and XL21 incorporate automatic keystone correction and digital zoom capabilities, ensuring that images are always perfectly aligned regardless of projector placement. They also come equipped with robust security features, which are essential in corporate environments. This includes password protection and a security bar, adding an extra layer of protection against unauthorized access.

In conclusion, the Mitsubishi Electronics XL50 and XL21 projectors stand out for their exceptional brightness, advanced color technologies, and user-friendly features. They are designed to meet the diverse needs of various professional settings, whether delivering impactful presentations in large auditoriums or facilitating engaging learning experiences in classrooms. As a result, these projectors exemplify Mitsubishi Electronics’ dedication to innovation and quality in the display technology industry.
Top Page Image Contents