Mitsubishi Electronics XL50, XL21 Indication This adjustment is normally unnecessary

Page 40

1.5.1.11. INDICATION

This adjustment is normally unnecessary.

Used to set how to indicate the status information.

1.5.1.11.1.WARNING (for Changer)

This is to set the indication of a warning mark on screen to induce to replace the spare lamp after auto-lamp changing or pre-announcement of the changing (“2.1.3.5 Warning indication”, on page 80).

•OFF: No indication.

•MESSAGE, ☀: To display both pre-announcement of auto-lamp changing and a warning mark to induce to replace the spare lamp.

•☀: To display only the warning mark.

[Procedure]

1.Select WARNING in INDICATION in MISC FUNCTION in the system menu.

2.Set OFF, MESSAGE ☀ or ☀.

1.5.1.11.2.STANDBY

This is to set a blue LED indication on screen (“3.5 LED display”, on page 91) at stand-by state.

•LED: To light the blue LED on screen.

•OFF: No indication.

[Procedure]

1.Select STANDBY in INDICATION in MISC FUNCTION in the system menu.

2.Set LED or OFF.

1.5.1.11.3.ERROR

This is to set a blue LED indication on screen (“3.5 LED display”, on page 91) at shutdown due to errors.

•LED: To blink the blue LED on screen.

•OFF: No indication.

[Procedure]

1.Select ERROR in INDICATION in MISC FUNCTION in the system menu.

2.Set LED or OFF.

1.5.1.11.4. BLOWOUT (for XL21 or when the input board is selected in PH50 and XL50)

This is to set a blue LED indication on screen (“3.5 LED display”, on page 91) at lamp blowout when BLOWOUT (chapter 1.5.1.13, on page 41) is set OPERATE.

•LED: To blink the blue LED on screen.

•OFF: No indication.

[Procedure]

1.Select BLOWOUT in INDICATION in MISC FUNCTION in the system menu.

2.Set LED or OFF.

PH50, XL50, XL21 series Set-up and Installation Manual

40

Page 39 Page 41
Image 40
Page 39 Page 41
Contents Set-up and Installation Manual Table of Contents REV 118 Flowchart Set-up and installation OverviewProduct lineup Safety precaution Cube installationPreparation Input board installation optional Unlocking for XL21 Color wheel unlockingLamp cushion removing for Changer Cube stacking for Rear Assembling the base stands and cubes PH50Screen gap adjustment Fixing to the wall and floor Cube stacking for Front Tape peeling off forScreen detaching Ventilation For 67 , 50 ChangerFor 50 Single External AC fan attaching occasional Assembling base stands and cubes As needed, you can adjust the screen gaps Adjustment Screen open/close for Front Screen openingScreen closing Connecting Control signal connectionImage signal connection Case of daisy chainFor other than daisy chain Internal cabling for FrontInitial set up Menu operation Control button listOperation mode Basic menu operation Remote IDPicture outline adjustment Dipswitch settingDisplaying internal test pattern Axis adjustment AttachingFront Close the screen .2.7.2, on Adjustment DetachingPosition Keystone Tilt Zoom Correct the horizontal keystone distortion Mirror adjustment 50 XL21 XL50 Rear and PH50 System memory setting System set up Lamp PowerLamp Mode for XL21 This adjustment is normally unnecessary Terminate This adjustment is normally unnecessaryStart Memory Overlap for the input boardBaud Rate Image Flip This adjustment is normally unnecessarySystem Sync Indication This adjustment is normally unnecessary Auto Power on Extended IDDirection This adjustment is normally unnecessary Resolution for PH50 This adjustment is normally unnecessaryCable Length for PH50 and XL50 Lamp Change for ChangerColor balance adjustment Black Level This adjustment is not necessaryREV White Balance GradationTarget Color SensorImage set up Color MatrixuserADV.COL This adjustment is normally unnecessary ADV.DARK This adjustment is normally unnecessaryGamma This adjustment is normally unnecessary Dither This adjustment is normally unnecessaryWhite Boost This adjustment is normally unnecessary Automatic input signal scanning Input memory setting for the main inputInput port selecting Signal adjustment 3.1. H.POSITION, V.POSITIONFine for Analog input AMP Gain for Analog inputSignal Select for XL21 Signal SelectClamp START=0, Clamp WIDTH=0. Procedure Contrast BrightnessColor Matrix ApertureInput memory saving Input memory calling/deletingInput memory setting for the input board Expansion setting4.1. H.POSITION, V.POSITION Fine for S.ANALOG inputAMP. Gain for S.ANALOG input Value is automatically set in automatic input signal ScanningClamp START=0, Clamp WIDTH=0. Procedure With VC-B20KA Brightness VCR Mode for Composite or Y/C input with VC-B20KV ASPECT-RATIOColor for Composite or Y/C input Tint for Composite or Y/C inputInput memory saving Input Memory Display memory setting for the input board2. H.DISPLAY POS, V.DISPLAY POS Screen Mode Digital OUTDisplay memory saving Display memory calling/deletingSetting as daisy chain connection for the input board Display POS /1 Regular maintenance 2.1. Lamp replacement Safety precautionsProcedure For SingleTighten the two lamp fixing screws For Changer Open the lamp cover Close the lamp cover Partition door Action in lamp failure burnout or explosion Auto-lamp changing function for ChangerAction in brightness deterioration Manual lamp swap Lamp position auto calibrationLamp will Exchange Soon Condenser lens adjustment for Single Focus adjustment Cleaning Cleaning procedureScreen front surface CabinetFilter Reset Filter TimeAxis adjuster fixing For deliveryColor wheel locking for XL21 Lamp cushion inserting forFront Screen-holding arm locking for 67 FrontFunction Memories Menu treesInput memory Common itemsAdditional items When S.DIGITAL is selected Additional items When Analog or S.ANALOG is selectedDisplay memory System memory Items within parentheses are initial valuesMemory list display Control panel Test pattern listLED display LED display list RS-232C terminal Terminal functionsControl terminal Available input signal list RGB signal Ycbcr Ypbpr component video signal Motorized adjustment tool, S-AXL50E specification AccessoryApplicable product Outline drawingTerminals Outline Terminal for firmware upgrading/slide switchRotary dial Reset button Recovery procedure from errorTrouble shooting LEDInstallation Adjustment software, Wallaby 4.1. GeneralInitial set-up System configuration setting Automatic panel ID settingManual panel ID setting Serial port settingAdjustment Serial port openingTurning on Picture mute offService tab for system memory MaintenanceAuto CSC function Optimize gain functionInstallation Misc Function Input tab for input memory 107 Additional items When Composite or Y/C is selected Display tab for display memory Memory tab Information tabMemory copy Cube data saving Memory backupData sending to cubes Power and Mute Main windowPanel selection area Serial PortMenu bar Edit menu Read Parameter Send ParameterCopy Parameter Paste ParameterSystem Config menu By n 1x1, 2x2, 3x3 or Other Wall Config…Cube ID Setting Auto IDPort Setting Special menu Protect SettingSerial Port menu Log… OpenAbout trademarks Revision history Description Revision date

XL21, XL50 specifications

Mitsubishi Electronics has consistently set benchmarks in the realm of display technologies, and their XL50 and XL21 projector series showcases this commitment to excellence. These models are meticulously designed to cater to a variety of professional environments, making them indispensable tools for businesses, education, and large venues.

The flagship XL50 projectors offer superior brightness with an impressive maximum output, ensuring vivid images even in well-lit rooms. With a native resolution that supports Full HD content, users can expect crystal-clear presentations that captivate audiences. The XL50 also incorporates advanced color reproduction technologies, which provide a wide color gamut for dynamic visual experiences. The projectors utilize Mitsubishi’s proprietary 3LCD technology, which enhances color accuracy and brightness, allowing for incredible detail and realism in every projected image.

In contrast, the XL21 models are tailored for users seeking a balance between affordability and performance. While slightly less powerful than the XL50, these projectors still deliver remarkable brightness, making them suitable for small to medium-sized meeting rooms and classrooms. The XL21 also features a compact and lightweight design, facilitating easy transportation and setup. With a focus on user-friendly operation, both models offer intuitive interfaces and connectivity options, including HDMI ports, VGA connections, and wireless capabilities, enabling seamless integration with other devices.

In terms of advanced features, both the XL50 and XL21 incorporate automatic keystone correction and digital zoom capabilities, ensuring that images are always perfectly aligned regardless of projector placement. They also come equipped with robust security features, which are essential in corporate environments. This includes password protection and a security bar, adding an extra layer of protection against unauthorized access.

In conclusion, the Mitsubishi Electronics XL50 and XL21 projectors stand out for their exceptional brightness, advanced color technologies, and user-friendly features. They are designed to meet the diverse needs of various professional settings, whether delivering impactful presentations in large auditoriums or facilitating engaging learning experiences in classrooms. As a result, these projectors exemplify Mitsubishi Electronics’ dedication to innovation and quality in the display technology industry.
Top Page Image Contents