Mitsubishi Electronics XL50, XL21 installation manual Procedure, For Single

Page 72

2.1.2.Procedure

2.1.2.1.For Single

1.Rear: Hold down the handles by the fingers and pull the lower door to open.

Front: Open the screen unit (chapter 1.2.7.1, on page 21).

Lower door

Handles

2.Turn off the main power switch and unplug the power cord from the wall outlet.

3.Loosen the two lamp fixing screws.

4.Hold the handle and pull out the lamp.

•Be sure to grip the handle with one hand and hold the lamp with the other hand to pull it out safely.

•Do not touch the glass envelope of the lamp. It may burn you.

Lamp fixing screws

Handle

5.Insert a new lamp into the lamp chamber to the end.

•Do not touch the glass envelope of the lamp by your fingers. Oil on your fingers may cause damage or explosion of the lamp.

•Be sure to grip the handle with one hand and hold the lamp with the other hand to insert it safely. Be careful not to pinch your hand in the lamp chamber.

PH50, XL50, XL21 series Set-up and Installation Manual

72

Page 71 Page 73
Image 72
Page 71 Page 73
Contents Set-up and Installation Manual Table of Contents REV 118 Set-up and installation Overview FlowchartProduct lineup Cube installation Safety precautionPreparation Input board installation optional Unlocking for XL21 Color wheel unlockingLamp cushion removing for Changer Cube stacking for Rear Assembling the base stands and cubes PH50Screen gap adjustment Fixing to the wall and floor Cube stacking for Front Tape peeling off forScreen detaching Ventilation For 67 , 50 ChangerFor 50 Single External AC fan attaching occasional Assembling base stands and cubes As needed, you can adjust the screen gaps Adjustment Screen open/close for Front Screen openingScreen closing Connecting Control signal connectionImage signal connection Case of daisy chainFor other than daisy chain Internal cabling for FrontInitial set up Menu operation Control button listOperation mode Basic menu operation Remote IDDipswitch setting Picture outline adjustmentDisplaying internal test pattern Axis adjustment AttachingFront Close the screen .2.7.2, on Adjustment DetachingPosition Keystone Tilt Zoom Correct the horizontal keystone distortion Mirror adjustment 50 XL21 XL50 Rear and PH50 System memory setting System set up Lamp PowerLamp Mode for XL21 This adjustment is normally unnecessary Terminate This adjustment is normally unnecessaryStart Memory Overlap for the input boardImage Flip This adjustment is normally unnecessary Baud RateSystem Sync Indication This adjustment is normally unnecessary Auto Power on Extended IDResolution for PH50 This adjustment is normally unnecessary Direction This adjustment is normally unnecessaryCable Length for PH50 and XL50 Lamp Change for ChangerColor balance adjustment Black Level This adjustment is not necessaryREV White Balance GradationTarget Color SensorImage set up Color MatrixuserADV.COL This adjustment is normally unnecessary ADV.DARK This adjustment is normally unnecessaryGamma This adjustment is normally unnecessary Dither This adjustment is normally unnecessaryWhite Boost This adjustment is normally unnecessary Input memory setting for the main input Automatic input signal scanningInput port selecting Signal adjustment 3.1. H.POSITION, V.POSITIONFine for Analog input AMP Gain for Analog inputSignal Select for XL21 Signal SelectClamp START=0, Clamp WIDTH=0. Procedure Contrast BrightnessColor Matrix ApertureInput memory saving Input memory calling/deletingInput memory setting for the input board Expansion setting4.1. H.POSITION, V.POSITION Fine for S.ANALOG inputAMP. Gain for S.ANALOG input Value is automatically set in automatic input signal ScanningClamp START=0, Clamp WIDTH=0. Procedure With VC-B20KA Brightness VCR Mode for Composite or Y/C input with VC-B20KV ASPECT-RATIOColor for Composite or Y/C input Tint for Composite or Y/C inputInput memory saving Display memory setting for the input board Input Memory2. H.DISPLAY POS, V.DISPLAY POS Screen Mode Digital OUTDisplay memory saving Display memory calling/deletingSetting as daisy chain connection for the input board Display POS /1 Regular maintenance 2.1. Lamp replacement Safety precautionsProcedure For SingleTighten the two lamp fixing screws For Changer Open the lamp cover Close the lamp cover Partition door Auto-lamp changing function for Changer Action in lamp failure burnout or explosionAction in brightness deterioration Manual lamp swap Lamp position auto calibrationLamp will Exchange Soon Condenser lens adjustment for Single Focus adjustment Cleaning Cleaning procedureScreen front surface CabinetFilter Reset Filter TimeAxis adjuster fixing For deliveryColor wheel locking for XL21 Lamp cushion inserting forFront Screen-holding arm locking for 67 FrontFunction Memories Menu treesInput memory Common itemsAdditional items When Analog or S.ANALOG is selected Additional items When S.DIGITAL is selectedDisplay memory System memory Items within parentheses are initial valuesMemory list display Test pattern list Control panelLED display LED display list Terminal functions RS-232C terminalControl terminal Available input signal list RGB signal Ycbcr Ypbpr component video signal Motorized adjustment tool, S-AXL50E specification AccessoryApplicable product Outline drawingTerminal for firmware upgrading/slide switch Terminals OutlineRotary dial Reset button Recovery procedure from errorTrouble shooting LEDAdjustment software, Wallaby 4.1. General InstallationInitial set-up System configuration setting Automatic panel ID settingManual panel ID setting Serial port settingAdjustment Serial port openingTurning on Picture mute offService tab for system memory MaintenanceAuto CSC function Optimize gain functionInstallation Misc Function Input tab for input memory 107 Additional items When Composite or Y/C is selected Display tab for display memory Memory tab Information tabMemory copy Memory backup Cube data savingData sending to cubes Power and Mute Main windowPanel selection area Serial PortMenu bar Edit menu Read Parameter Send ParameterCopy Parameter Paste ParameterSystem Config menu By n 1x1, 2x2, 3x3 or Other Wall Config…Cube ID Setting Auto IDPort Setting Special menu Protect SettingSerial Port menu Log… OpenAbout trademarks Revision history Description Revision date

XL21, XL50 specifications

Mitsubishi Electronics has consistently set benchmarks in the realm of display technologies, and their XL50 and XL21 projector series showcases this commitment to excellence. These models are meticulously designed to cater to a variety of professional environments, making them indispensable tools for businesses, education, and large venues.

The flagship XL50 projectors offer superior brightness with an impressive maximum output, ensuring vivid images even in well-lit rooms. With a native resolution that supports Full HD content, users can expect crystal-clear presentations that captivate audiences. The XL50 also incorporates advanced color reproduction technologies, which provide a wide color gamut for dynamic visual experiences. The projectors utilize Mitsubishi’s proprietary 3LCD technology, which enhances color accuracy and brightness, allowing for incredible detail and realism in every projected image.

In contrast, the XL21 models are tailored for users seeking a balance between affordability and performance. While slightly less powerful than the XL50, these projectors still deliver remarkable brightness, making them suitable for small to medium-sized meeting rooms and classrooms. The XL21 also features a compact and lightweight design, facilitating easy transportation and setup. With a focus on user-friendly operation, both models offer intuitive interfaces and connectivity options, including HDMI ports, VGA connections, and wireless capabilities, enabling seamless integration with other devices.

In terms of advanced features, both the XL50 and XL21 incorporate automatic keystone correction and digital zoom capabilities, ensuring that images are always perfectly aligned regardless of projector placement. They also come equipped with robust security features, which are essential in corporate environments. This includes password protection and a security bar, adding an extra layer of protection against unauthorized access.

In conclusion, the Mitsubishi Electronics XL50 and XL21 projectors stand out for their exceptional brightness, advanced color technologies, and user-friendly features. They are designed to meet the diverse needs of various professional settings, whether delivering impactful presentations in large auditoriums or facilitating engaging learning experiences in classrooms. As a result, these projectors exemplify Mitsubishi Electronics’ dedication to innovation and quality in the display technology industry.
Top Page Image Contents