1.5.1.8. BAUD RATE
Used to select the transmission speed of RS-232 in accordance with an external controller setting. The initial setting is 19200 (19,200bps). You can select 9,600bps or 19,200bps. [Procedure]
1.Select BAUD RATE in MISC FUNCTION in the system menu.
2.Set 9600 or 19200.
1.5.1.9. SYSTEM SYNC
Used to set a vertical synchronizing frequency in accordance with a moving pictures signal to be mainly displayed. The initial setting is 60 (60Hz). Set 60Hz for NTSC signal or 50Hz for PAL signal. All cubes in a display wall should be the same setting.
[Procedure]
1.Select SYSTEM SYNC in MISC FUNCTION in the system menu.
2.Set 60 or 50.
1.5.1.10. IMAGE FLIP
This adjustment is normally unnecessary.
Used to invert the displayed image vertically or horizontally. Rear
should be set S/W for the normal image.
•S/W: Normal image
•S/E: Vertically flipped image
•N/W: Horizontally flipped image
•N/E: Vertically/horizontally flipped image [Procedure]
1.Select IMAGE FLIP in MISC FUNCTION in the system menu.
2.Set S/W, S/E, N/W or N/E.
REV 2.4
39
Set-up and Installation Manual
Table of Contents
REV
118
Set-up and installation Overview
Flowchart
Product lineup
Cube installation
Safety precaution
Preparation
Input board installation optional
Color wheel unlocking
Unlocking for XL21
Lamp cushion removing for Changer
PH50
Cube stacking for Rear Assembling the base stands and cubes
Screen gap adjustment
Fixing to the wall and floor
Tape peeling off for
Cube stacking for Front
Screen detaching
For 67 , 50 Changer
Ventilation
For 50 Single
External AC fan attaching occasional
Assembling base stands and cubes
As needed, you can adjust the screen gaps
Adjustment
Screen opening
Screen open/close for Front
Screen closing
Case of daisy chain
Connecting
Control signal connection
Image signal connection
Internal cabling for Front
For other than daisy chain
Menu operation Control button list
Initial set up
Operation mode
Remote ID
Basic menu operation
Dipswitch setting
Picture outline adjustment
Displaying internal test pattern
Attaching
Axis adjustment
Front Close the screen .2.7.2, on
Detaching
Adjustment
Position Keystone Tilt Zoom
Correct the horizontal keystone distortion
Mirror adjustment
50 XL21
XL50 Rear and PH50
Terminate This adjustment is normally unnecessary
System memory setting
System set up Lamp Power
Lamp Mode for XL21 This adjustment is normally unnecessary
Overlap for the input board
Start Memory
Image Flip This adjustment is normally unnecessary
Baud Rate
System Sync
Indication This adjustment is normally unnecessary
Extended ID
Auto Power on
Resolution for PH50 This adjustment is normally unnecessary
Direction This adjustment is normally unnecessary
Cable Length for PH50 and XL50
Changer
Lamp Change for
Black Level This adjustment is not necessary
Color balance adjustment
REV
Gradation
White Balance
Sensor
Target Color
Color Matrixuser
Image set up
Dither This adjustment is normally unnecessary
ADV.COL This adjustment is normally unnecessary
ADV.DARK This adjustment is normally unnecessary
Gamma This adjustment is normally unnecessary
White Boost This adjustment is normally unnecessary
Input memory setting for the main input
Automatic input signal scanning
Input port selecting
AMP Gain for Analog input
Signal adjustment
3.1. H.POSITION, V.POSITION
Fine for Analog input
Signal Select
Signal Select for XL21
Clamp START=0, Clamp WIDTH=0. Procedure
Aperture
Contrast
Brightness
Color Matrix
Input memory calling/deleting
Input memory saving
Expansion setting
Input memory setting for the input board
Fine for S.ANALOG input
4.1. H.POSITION, V.POSITION
AMP. Gain for S.ANALOG input
Scanning
Value is automatically set in automatic input signal
Clamp START=0, Clamp WIDTH=0. Procedure
With VC-B20KA
Brightness
Tint for Composite or Y/C input
VCR Mode for Composite or Y/C input with VC-B20KV
ASPECT-RATIO
Color for Composite or Y/C input
Input memory saving
Display memory setting for the input board
Input Memory
2. H.DISPLAY POS, V.DISPLAY POS
Digital OUT
Screen Mode
Display memory calling/deleting
Display memory saving
Setting as daisy chain connection for the input board
Display POS /1
Safety precautions
Regular maintenance 2.1. Lamp replacement
For Single
Procedure
Tighten the two lamp fixing screws
For Changer
Open the lamp cover
Close the lamp cover
Partition door
Auto-lamp changing function for Changer
Action in lamp failure burnout or explosion
Action in brightness deterioration
Lamp position auto calibration
Manual lamp swap
Lamp will Exchange Soon
Condenser lens adjustment for Single
Focus adjustment
Cabinet
Cleaning
Cleaning procedure
Screen front surface
Filter Time
Filter Reset
Lamp cushion inserting for
Axis adjuster fixing
For delivery
Color wheel locking for XL21
Screen-holding arm locking for 67 Front
Front
Common items
Function Memories
Menu trees
Input memory
Additional items When Analog or S.ANALOG is selected
Additional items When S.DIGITAL is selected
Display memory
Items within parentheses are initial values
System memory
Memory list display
Test pattern list
Control panel
LED display
LED display list
Terminal functions
RS-232C terminal
Control terminal
Available input signal list RGB signal
Ycbcr Ypbpr component video signal
Outline drawing
Motorized adjustment tool, S-AXL50E specification
Accessory
Applicable product
Terminal for firmware upgrading/slide switch
Terminals Outline
Rotary dial
LED
Reset button
Recovery procedure from error
Trouble shooting
Adjustment software, Wallaby 4.1. General
Installation
Initial set-up
Serial port setting
System configuration setting
Automatic panel ID setting
Manual panel ID setting
Picture mute off
Adjustment
Serial port opening
Turning on
Maintenance
Service tab for system memory
Optimize gain function
Auto CSC function
Installation
Misc Function
Input tab for input memory
107
Additional items When Composite or Y/C is selected
Display tab for display memory
Information tab
Memory tab
Memory copy
Memory backup
Cube data saving
Data sending to cubes
Serial Port
Power and Mute
Main window
Panel selection area
Menu bar
Paste Parameter
Edit menu Read Parameter
Send Parameter
Copy Parameter
Auto ID
System Config menu By n 1x1, 2x2, 3x3 or
Other Wall Config…
Cube ID Setting
Open
Port Setting
Special menu Protect Setting
Serial Port menu Log…
About trademarks
Description Revision date
Revision history