Mitsubishi Electronics XL21 installation manual Cable Length for PH50 and XL50

Page 42

1.5.1.15. CABLE LENGTH (for PH50 and XL50)

Used to set it according to a digital cable length of image inputs. The initial setting is NORMAL. Set LONG when image noise is noticeable due to a transmission attenuation through a long digital cable such as over 5 meters. As needed, CUSTOM menu can be selected for more detailed adjustment.

[Procedure]

1.Select CABLE LENGTH in MISC FUNCTION in the system menu.

2.Select DIGITAL or S.DIGITAL according to the input port.

3.Set NORMAL, LONG or CUSTOM.

4.When selecting the CUSTOM menu, adjust the LEVEL value so that the noise on images will be minimized. The adjusting range is 0 – 15. The initial value is 13.

1.5.1.16. RESOLUTION (for PH50)

This adjustment is normally unnecessary.

Used to switch SXGA and SXGA+ resolution. The initial setting is SXGA+.

•SXGA: SXGA resolution image (1280 x 1024 pixels) is displayed with black outer margins on SXGA+ screen.

•SXGA+: SXGA+ resolution image (1400 x 1050 pixels) is displayed.

[Procedure]

1.Select RESOLUTION in MISC FUNCTION in the system menu.

2.Set SXGA or SXGA+.

1.5.1.17. DIRECTION

This adjustment is normally unnecessary.

Used to set when you substitute an optical unit of Rear for Front and vice versa.

•REAR: Select for Rear.

•FRONT: Select for Front. FILTER RESET and FILTER TIME menus (on page 84) will be active in the system menu. The filter time is counted up even during REAR mode. Reset the filter time (chapter 2.4.3.3, on page 84) when switch to FRONT.

[Procedure]

1.Select DIRECTION in INSTALLATION in the system menu.

2.Set REAR or FRONT.

PH50, XL50, XL21 series Set-up and Installation Manual

42

Page 41 Page 43
Image 42
Page 41 Page 43
Contents Set-up and Installation Manual Table of Contents REV 118 Set-up and installation Overview FlowchartProduct lineup Cube installation Safety precautionPreparation Input board installation optional Unlocking for XL21 Color wheel unlockingLamp cushion removing for Changer Cube stacking for Rear Assembling the base stands and cubes PH50Screen gap adjustment Fixing to the wall and floor Cube stacking for Front Tape peeling off forScreen detaching Ventilation For 67 , 50 ChangerFor 50 Single External AC fan attaching occasional Assembling base stands and cubes As needed, you can adjust the screen gaps Adjustment Screen open/close for Front Screen openingScreen closing Image signal connection ConnectingControl signal connection Case of daisy chainFor other than daisy chain Internal cabling for FrontInitial set up Menu operation Control button listOperation mode Basic menu operation Remote IDDipswitch setting Picture outline adjustmentDisplaying internal test pattern Axis adjustment AttachingFront Close the screen .2.7.2, on Adjustment DetachingPosition Keystone Tilt Zoom Correct the horizontal keystone distortion Mirror adjustment 50 XL21 XL50 Rear and PH50 Lamp Mode for XL21 This adjustment is normally unnecessary System memory settingSystem set up Lamp Power Terminate This adjustment is normally unnecessaryStart Memory Overlap for the input boardImage Flip This adjustment is normally unnecessary Baud RateSystem Sync Indication This adjustment is normally unnecessary Auto Power on Extended IDResolution for PH50 This adjustment is normally unnecessary Direction This adjustment is normally unnecessaryCable Length for PH50 and XL50 Lamp Change for ChangerColor balance adjustment Black Level This adjustment is not necessaryREV White Balance GradationTarget Color SensorImage set up Color MatrixuserGamma This adjustment is normally unnecessary ADV.COL This adjustment is normally unnecessaryADV.DARK This adjustment is normally unnecessary Dither This adjustment is normally unnecessaryWhite Boost This adjustment is normally unnecessary Input memory setting for the main input Automatic input signal scanningInput port selecting Fine for Analog input Signal adjustment3.1. H.POSITION, V.POSITION AMP Gain for Analog inputSignal Select for XL21 Signal SelectClamp START=0, Clamp WIDTH=0. Procedure Color Matrix ContrastBrightness ApertureInput memory saving Input memory calling/deletingInput memory setting for the input board Expansion setting4.1. H.POSITION, V.POSITION Fine for S.ANALOG inputAMP. Gain for S.ANALOG input Value is automatically set in automatic input signal ScanningClamp START=0, Clamp WIDTH=0. Procedure With VC-B20KA Brightness Color for Composite or Y/C input VCR Mode for Composite or Y/C input with VC-B20KVASPECT-RATIO Tint for Composite or Y/C inputInput memory saving Display memory setting for the input board Input Memory2. H.DISPLAY POS, V.DISPLAY POS Screen Mode Digital OUTDisplay memory saving Display memory calling/deletingSetting as daisy chain connection for the input board Display POS /1 Regular maintenance 2.1. Lamp replacement Safety precautionsProcedure For SingleTighten the two lamp fixing screws For Changer Open the lamp cover Close the lamp cover Partition door Auto-lamp changing function for Changer Action in lamp failure burnout or explosionAction in brightness deterioration Manual lamp swap Lamp position auto calibrationLamp will Exchange Soon Condenser lens adjustment for Single Focus adjustment Screen front surface CleaningCleaning procedure CabinetFilter Reset Filter TimeColor wheel locking for XL21 Axis adjuster fixingFor delivery Lamp cushion inserting forFront Screen-holding arm locking for 67 FrontInput memory Function MemoriesMenu trees Common itemsAdditional items When Analog or S.ANALOG is selected Additional items When S.DIGITAL is selectedDisplay memory System memory Items within parentheses are initial valuesMemory list display Test pattern list Control panelLED display LED display list Terminal functions RS-232C terminalControl terminal Available input signal list RGB signal Ycbcr Ypbpr component video signal Applicable product Motorized adjustment tool, S-AXL50E specificationAccessory Outline drawingTerminal for firmware upgrading/slide switch Terminals OutlineRotary dial Trouble shooting Reset buttonRecovery procedure from error LEDAdjustment software, Wallaby 4.1. General InstallationInitial set-up Manual panel ID setting System configuration settingAutomatic panel ID setting Serial port settingTurning on AdjustmentSerial port opening Picture mute offService tab for system memory MaintenanceAuto CSC function Optimize gain functionInstallation Misc Function Input tab for input memory 107 Additional items When Composite or Y/C is selected Display tab for display memory Memory tab Information tabMemory copy Memory backup Cube data savingData sending to cubes Panel selection area Power and MuteMain window Serial PortMenu bar Copy Parameter Edit menu Read ParameterSend Parameter Paste ParameterCube ID Setting System Config menu By n 1x1, 2x2, 3x3 orOther Wall Config… Auto IDSerial Port menu Log… Port SettingSpecial menu Protect Setting OpenAbout trademarks Revision history Description Revision date

XL21, XL50 specifications

Mitsubishi Electronics has consistently set benchmarks in the realm of display technologies, and their XL50 and XL21 projector series showcases this commitment to excellence. These models are meticulously designed to cater to a variety of professional environments, making them indispensable tools for businesses, education, and large venues.

The flagship XL50 projectors offer superior brightness with an impressive maximum output, ensuring vivid images even in well-lit rooms. With a native resolution that supports Full HD content, users can expect crystal-clear presentations that captivate audiences. The XL50 also incorporates advanced color reproduction technologies, which provide a wide color gamut for dynamic visual experiences. The projectors utilize Mitsubishi’s proprietary 3LCD technology, which enhances color accuracy and brightness, allowing for incredible detail and realism in every projected image.

In contrast, the XL21 models are tailored for users seeking a balance between affordability and performance. While slightly less powerful than the XL50, these projectors still deliver remarkable brightness, making them suitable for small to medium-sized meeting rooms and classrooms. The XL21 also features a compact and lightweight design, facilitating easy transportation and setup. With a focus on user-friendly operation, both models offer intuitive interfaces and connectivity options, including HDMI ports, VGA connections, and wireless capabilities, enabling seamless integration with other devices.

In terms of advanced features, both the XL50 and XL21 incorporate automatic keystone correction and digital zoom capabilities, ensuring that images are always perfectly aligned regardless of projector placement. They also come equipped with robust security features, which are essential in corporate environments. This includes password protection and a security bar, adding an extra layer of protection against unauthorized access.

In conclusion, the Mitsubishi Electronics XL50 and XL21 projectors stand out for their exceptional brightness, advanced color technologies, and user-friendly features. They are designed to meet the diverse needs of various professional settings, whether delivering impactful presentations in large auditoriums or facilitating engaging learning experiences in classrooms. As a result, these projectors exemplify Mitsubishi Electronics’ dedication to innovation and quality in the display technology industry.
Top Page Image Contents