1.8. Display memory setting (for the input board)
Used to set an image position and expansion ratio for the input board signals to display on a display wall.
Press [MENU2] button to display the display memory menus. You can exit the menu by [ESC] button. There is no need to register the display memory when the input board is not attached. In this case, the display memory menu is not displayed.
1.8.1.INPUT MEMORY
Used to designate an input image signal to be displayed. [Procedure]
1.Select INPUT MEMORY in the display memory menu.
2.Select an input memory number to be displayed. Current displaying memory is called at first. If the input memory has not been saved, it displays “BLANK MEMORY” and the display memory cannot be saved. In this case, save the input memory in advance (chapter 1.7.6, on page 65).
1.8.2.H.DISPLAY POS, V.DISPLAY POS
Used to adjust an image position and expansion ratio according to a configuration. [Procedure]
1.Select H.DISPLAY POS. or V. DISPLAY POS in the display memory menu.
2.Set the values of H.DISPLAY POS. and V. DISPLAY POS. The “n” of n/m indicates the panel position in the vertical and horizontal directions. The “m” indicates the total number of screens in the directions. To display an un-scaled image on each cube, set the both menus 1/1.
•For the detail setting for daisy-chained display walls, see “1.9 Setting as daisy chain connection” on page 69.
•DISPLAY menu (chapter 1.8.4, on page 67) can tweak an unmatched image linkage between screens.
1.8.3.CROP
This adjustment is normally unnecessary. The optimum value is automatically renewed when H./V. DISPLAY POS. are changed.
Used to clip a partial area from an effective image area by manual. The adjustment is required only in a specific case.
•H.POSITION: The horizontal starting position of the partial area.
•V.POSITION: The vertical starting position of the partial area.
•H.SIZE: The horizontal size of the partial area.
•V.SIZE: The vertical size of the partial area.
[Procedure]
1.Select CROP in the display memory menu.
2.Adjust each item.
Note: It will be automatically renewed when H./V. DISPLAY POS. are changed.
PH50, XL50, XL21 series Set-up and Installation Manual
66
Set-up and Installation Manual
Table of Contents
REV
118
Set-up and installation Overview
Flowchart
Product lineup
Cube installation
Safety precaution
Preparation
Input board installation optional
Unlocking for XL21
Color wheel unlocking
Lamp cushion removing for Changer
Cube stacking for Rear Assembling the base stands and cubes
PH50
Screen gap adjustment
Fixing to the wall and floor
Cube stacking for Front
Tape peeling off for
Screen detaching
Ventilation
For 67 , 50 Changer
For 50 Single
External AC fan attaching occasional
Assembling base stands and cubes
As needed, you can adjust the screen gaps
Adjustment
Screen open/close for Front
Screen opening
Screen closing
Image signal connection
Connecting
Control signal connection
Case of daisy chain
For other than daisy chain
Internal cabling for Front
Initial set up
Menu operation Control button list
Operation mode
Basic menu operation
Remote ID
Dipswitch setting
Picture outline adjustment
Displaying internal test pattern
Axis adjustment
Attaching
Front Close the screen .2.7.2, on
Adjustment
Detaching
Position Keystone Tilt Zoom
Correct the horizontal keystone distortion
Mirror adjustment
50 XL21
XL50 Rear and PH50
Lamp Mode for XL21 This adjustment is normally unnecessary
System memory setting
System set up Lamp Power
Terminate This adjustment is normally unnecessary
Start Memory
Overlap for the input board
Image Flip This adjustment is normally unnecessary
Baud Rate
System Sync
Indication This adjustment is normally unnecessary
Auto Power on
Extended ID
Resolution for PH50 This adjustment is normally unnecessary
Direction This adjustment is normally unnecessary
Cable Length for PH50 and XL50
Lamp Change for
Changer
Color balance adjustment
Black Level This adjustment is not necessary
REV
White Balance
Gradation
Target Color
Sensor
Image set up
Color Matrixuser
Gamma This adjustment is normally unnecessary
ADV.COL This adjustment is normally unnecessary
ADV.DARK This adjustment is normally unnecessary
Dither This adjustment is normally unnecessary
White Boost This adjustment is normally unnecessary
Input memory setting for the main input
Automatic input signal scanning
Input port selecting
Fine for Analog input
Signal adjustment
3.1. H.POSITION, V.POSITION
AMP Gain for Analog input
Signal Select for XL21
Signal Select
Clamp START=0, Clamp WIDTH=0. Procedure
Color Matrix
Contrast
Brightness
Aperture
Input memory saving
Input memory calling/deleting
Input memory setting for the input board
Expansion setting
4.1. H.POSITION, V.POSITION
Fine for S.ANALOG input
AMP. Gain for S.ANALOG input
Value is automatically set in automatic input signal
Scanning
Clamp START=0, Clamp WIDTH=0. Procedure
With VC-B20KA
Brightness
Color for Composite or Y/C input
VCR Mode for Composite or Y/C input with VC-B20KV
ASPECT-RATIO
Tint for Composite or Y/C input
Input memory saving
Display memory setting for the input board
Input Memory
2. H.DISPLAY POS, V.DISPLAY POS
Screen Mode
Digital OUT
Display memory saving
Display memory calling/deleting
Setting as daisy chain connection for the input board
Display POS /1
Regular maintenance 2.1. Lamp replacement
Safety precautions
Procedure
For Single
Tighten the two lamp fixing screws
For Changer
Open the lamp cover
Close the lamp cover
Partition door
Auto-lamp changing function for Changer
Action in lamp failure burnout or explosion
Action in brightness deterioration
Manual lamp swap
Lamp position auto calibration
Lamp will Exchange Soon
Condenser lens adjustment for Single
Focus adjustment
Screen front surface
Cleaning
Cleaning procedure
Cabinet
Filter Reset
Filter Time
Color wheel locking for XL21
Axis adjuster fixing
For delivery
Lamp cushion inserting for
Front
Screen-holding arm locking for 67 Front
Input memory
Function Memories
Menu trees
Common items
Additional items When Analog or S.ANALOG is selected
Additional items When S.DIGITAL is selected
Display memory
System memory
Items within parentheses are initial values
Memory list display
Test pattern list
Control panel
LED display
LED display list
Terminal functions
RS-232C terminal
Control terminal
Available input signal list RGB signal
Ycbcr Ypbpr component video signal
Applicable product
Motorized adjustment tool, S-AXL50E specification
Accessory
Outline drawing
Terminal for firmware upgrading/slide switch
Terminals Outline
Rotary dial
Trouble shooting
Reset button
Recovery procedure from error
LED
Adjustment software, Wallaby 4.1. General
Installation
Initial set-up
Manual panel ID setting
System configuration setting
Automatic panel ID setting
Serial port setting
Turning on
Adjustment
Serial port opening
Picture mute off
Service tab for system memory
Maintenance
Auto CSC function
Optimize gain function
Installation
Misc Function
Input tab for input memory
107
Additional items When Composite or Y/C is selected
Display tab for display memory
Memory tab
Information tab
Memory copy
Memory backup
Cube data saving
Data sending to cubes
Panel selection area
Power and Mute
Main window
Serial Port
Menu bar
Copy Parameter
Edit menu Read Parameter
Send Parameter
Paste Parameter
Cube ID Setting
System Config menu By n 1x1, 2x2, 3x3 or
Other Wall Config…
Auto ID
Serial Port menu Log…
Port Setting
Special menu Protect Setting
Open
About trademarks
Revision history
Description Revision date