Onkyo TX-NR1008 Muting the AV Receiver, Using the Sleep Timer, Selecting Speaker Layout

Page 26

Muting the AV Receiver

You can temporarily mute the output of the AV receiver.

Press RECEIVER followed by MUTING.

The output is muted and the MUTING indicator flashes on the display.

Tip

•To unmute, press MUTING again or adjust the volume.

•The Mute function is cancelled when the AV receiver is set to Standby.

Using the Sleep Timer

With the sleep timer, you can set the AV receiver to turn off automatically after a specified period.

Press RECEIVER followed by SLEEP repeatedly to select the required sleep time.

The sleep time can be set from 90 to 10 minutes in 10 minute steps.

The SLEEP indicator lights on the display when the sleep timer has been set. The specified sleep time appears on the display for about 5 seconds, then the previous display reappears.

Tip

•If you need to cancel the sleep timer, press SLEEP repeatedly until the SLEEP indicator goes off.

•To check the time remaining until the AV receiver sleeps, press SLEEP. Note that if you press SLEEP while the sleep time is being displayed, you’ll shorten the sleep time by 10 minutes.

Selecting Speaker Layout

You can prioritize which speakers you want to use.

Press RECEIVER followed by SP LAYOUT

repeatedly.

■9.1 ch playback

`Speaker Layout:SB/FH:

The sounds from surround back and front high speakers are output by priority.

`Speaker Layout:SB/FW:

The sounds from surround back and front wide speakers are output by priority.

`Speaker Layout:FH/FW:

The sounds from front high and front wide speakers are output by priority.

■7.1 ch playback

`Speaker Layout:SB:

The sound from surround back speakers is out- put by priority.

`Speaker Layout:FH:

The sound from front high speakers is output by priority.

`Speaker Layout:FW:

The sound from front wide speakers is output by priority.

Note

•If the “Speakers Type(Front)” setting is set to “Bi-Amp”

(➔ 47), or Powered Zone 2 or Powered Zone 3 is being used (➔ 75), playback is reduced to 7.1-channels.

•When the listening mode that doesn’t support front high, front wide and surround back speakers is used, the setting cannot be selected.

En

26

Image 26

Contents Introduction Connections Advanced Operations Controlling iPod & Other ComponentsBoard above the apparatus shall be set 10 cm Always consider the environmental issues and follow10 cm 4 at the rear. The rear edge of the shelf or Away from the rear panel or wall, creating a flue-likePrecautions Installing the Batteries Supplied AccessoriesUsing the Remote Controller Aiming the Remote ControllerContents Amplifier Features40 FM/AM Presets excluding North American mod- els ProcessingTHX Select2 Plus Amplifier is prohibitedCBL/SAT , Game , PC , AUX , Tuner , TV/CD Front & Rear PanelsFront Panel Phones jack Zone 2, Zone 3 and OFF buttons Return button Setup MIC jackDisplay AUX Input jacks HDMI, VIDEO, Audio L/R and Digital 18Digital in Coaxial and Optical jacks UREMOTE Control jack Universal Port jack Ethernet portRear Panel Front L/R, CENTER, Surr L/RRemote Controller Controlling the AV ReceiverAbout Home Theater Enjoying Home TheaterSpeaker Configuration Connecting the AV ReceiverConnecting Your Speakers Speaker Connection PrecautionsConnecting the Speaker Cables Screw-type speaker terminals Strip 1/2 to 5/8 12 to 15 mmBi-amping the Front Speakers Using Dipole SpeakersConnecting Powered Subwoofers Connecting a Power Amplifier B c e Power amplifier I gAV Cables and Jacks About AV ConnectionsConnected image with AV components Hdmi cableAudio return channel ARC function Connecting Your Components with HdmiJack Signal Components Assignable Connecting Your Components Front RearRemote Control Connecting Onkyo uComponentsHow to record the video StepNorth American European and Asian Taiwan models Models Connecting AntennaConnecting the Power Cord AC InletWhich Connections Should I Use? Video Connection FormatsDepends on the Audio TV Out setting Monitor Out setting set to AnalogPC in Analog RGB input signal is output at 720p resolution Audio Connection FormatsTurning On Standby indicatorTurning On/Off the AV Receiver Turning OffBasic Operations Selecting the Language Used for the Onscreen Setup MenusSetting the Display Brightness Playing the Connected ComponentSelecting Speaker Layout Using the Sleep TimerMuting the AV Receiver Ch playbackUsing the Home Menu Changing the Input DisplayUsing Headphones Using Activities to Start Easy MacrosFirst measurement position Audyssey MultEQ Room Correction and Speaker SetupUsing Audyssey MultEQ EnterError Messages Changing the Speaker Settings Manually Using a Powered SubwooferListening to the Radio Using the TunerTuning into Radio Stations Listening to the RadioPresetting FM/AM Stations Using RDS excluding North American and Taiwan modelsRDS program types PTY Finding Stations by Type PTYListening to Traffic News TP AV Recording Connecting a Recording ComponentRecording Selecting Listening Modes Using the Listening ModesListening Mode Buttons Input Source About Listening ModesExplanatory Notes Speaker LayoutListening Modes DTS-HD Master Resolution AudioDescription Input Speaker Source Layout DTS-HD High AudioListening Mode Description Input Speaker Source Layout Onkyo-Original DSP Listening Modes Common Procedures in Setup Menu Advanced SetupOn-screen Setup Menus MenuOUT Main Input/Output AssignMonitor Out Changing Monitor Out setting manually ResolutionComponent Video Input Here are the default assignmentsHdmi Input BD/DVD, VCR/DVR, CBL/SAT, GAME, PC TV/CD, PHONO, PortBD/DVD, VCR/DVR, CBL/SAT, GAME, PC, AUX TV/CD, PHONO, Port Digital Audio InputAnalog Audio Input ` in 1,Speaker Setup Speaker SettingsSpeaker Distance Level CalibrationBGC Equalizer SettingsTHX Audio Setup Dolby Audio AdjustMultiplex/Mono LFE Level Theater-DimensionalAudyssey DSX Audyssey Source SetupDynamic Volume Dynamic EQName Edit IntelliVolumeSync To correct a character Picture AdjustGame Mode Wide Mode*1*3Film Mode*2*4*5 Resolution*2*4Picture Mode*1 Edge Enhancement*2*4Listening Mode Preset Hardware Setup MiscellaneousSirius Settings North American models TunerNetwork Auto Power DownFirmware Update Tone Control Settings Lock SetupUsing the Audio Settings Speaker LevelsMusic Optimizer Audyssey SettingsLate Night Re-EQAudio Selector Setting the Incoming Digital Signal Fixed ModeAudio Selector Network Requirements Connecting the AV ReceiverAbout NET Listening to vTuner Internet Radio Click on the Preset Internet Radio tabListening to Internet Radio Listening to Other Internet RadioPlaying Music Files on a Server Registering Presets*1Station and Song Presets Items on the Internet Radio Top MenuWindows Media Player 11 Setup WAV Supported Audio File FormatsWMA AACServer Requirements Windows Media Player 12 SetupRemote Playback from Media Server/ Personal Computer About DlnaNetwork Settings Using Remote PlaybackDhcp Playing Music Files on a USB Device About USBUSB Mass Storage Device Requirements Random Playback Connecting Your Zone 2 Speakers to an Amp in Zone Connecting ZoneConnecting Your Zone 2 Speakers Directly to the AV receiver Multi ZoneZone 3 12V Trigger Connecting Your Zone 3 Speakers Directly to the AV receiverConnecting Your Zone 3 Speakers to an Amp in Zone Connect your Zone 3 speakers to the AV receiver’s FrontSetting the Powered Zone 2/3 Setting the Multi ZoneControlling Zone 2/3 from the AV receiver Using Zone 2/3Controlling Zone 2/3 with the Remote Controller TORUsing a Multiroom Kit with Zone 2/3 Adjusting the Volume for ZonesAdjusting the Tone and Balance of Zone Muting ZonesUsing a Multiroom Kit with a Cabinet Using a Multiroom Kit with Other ComponentsExtended Mode control Connecting the iPod Directly to the USB PortStandard Mode control Controlling iPodOnkyo Dock Cable Connecting an Onkyo DockModels sold are different depending on the region Using the Onkyo Dock UP-A1 DockWithout the RI Control Controlling Your iPodRI Dock With the RI ControlUDock Available buttonsOnkyo Dock Buttons UP-A1 Dock E/rENTER PLAYLISTe/rControlling Other Components Preprogrammed Remote Control CodesLooking up for Remote Control Code Or if you are not sure about the exact model Use q/wto select Search by model numberVia network, and then press Enter Select Skip, and then press EnterEnter the appropriate remote control code for Entering Remote Control CodesRemote Control Codes for Onkyo Components Connected via u Remote Mode BD/DVDYou can reset the remote controller to its default settings Resetting Remote Mode ButtonsResetting the Remote Controller Controlling Other ComponentsTV VOL q/w Components ButtonsCassettetape deck CH + Disc +Activities Setup Message for transfer will appear Learning CommandsTo learn more commands, repeat steps 2 Running Macros Using Normal MacrosDeleting Learning Commands Deleting MacrosThere’s no sound, or it’s very quiet TroubleshootingStandby indicator flashes red Can’t turn on the AV receiverAbout DTS signals There’s no sound with a certain signal formatCan’t select the Pure Audio listening mode Only the center speaker produces soundThere’s no picture from a source connected to an Hdmi Remote controller doesn’t workThere’s no picture On-screen menus don’t appearCan’t access the music files on a USB device Can’t learn commands from another remote controllerCan’t access the server or Internet radio Stand-by power consumptionCBL/SAT, GAME, or AUX input How do I change the language of a multiplex sourceUfunctions don’t work Nent Video Monitor OUTGeneral SpecificationsAmplifier Section Tuner Section Video SectionAudio Outputs OthersAbout Copyright Protection About HdmiSupported Audio Formats Operations that can be performed with p connection Using an RIHD-compatible TV, Player, or RecorderAbout p-compatible components Confirm the settings How to connect and setupConfirm the connecting and setting Operate with the remote controllerOutput Video Resolution ChartOutput Memo 103Onkyo Europe Electronics GmbH Onkyo Europe Electronics GmbH UK Branch