Mitsubishi Electronics XL30 XL25 SL25 Troubleshooting, Problems Cause Possible Solutions

Page 24

Troubleshooting

The following offers solutions to some of the common problems you may encounter. We suggest that you consult this chart before contacting your dealer.

PROBLEMS

CAUSE

POSSIBLE SOLUTIONS

 

 

 

The power is off.

• The air inlet slots, outlet slots or air filter is

• Remove the object.

 

clogged with dust or some objects.

 

 

POWER indicator does not light up.

• Plug the power cord into the outlet.

 

• Power cord is unplugged from the outlet.

 

• Power cord is disconnected from the projector.

• Insert the power cord into the projector.

 

• The main switch is turned off.

• Turn the main switch on.

 

• The lamp lid is open.

• Close the lamp lid.

 

POWER indicator blinks red.

• Wait for the lighting sequence.

 

• The projector has been turned on again too soon

 

after having been turned off.

• Turn the power switch on and off several times.

 

• When the power switch was turned off while

 

the fan was running, during or after lamp

 

 

operation.

 

 

• The room temperature is too high.

• Refer to "Indicators" on page 25.

 

(Does the LAMP indicator show an unusual

 

 

condition?)

 

 

• Lamp is no longer working.

• Replace the lamp with a new one.

 

POWER indicator blinks between red and green.

 

 

• The filter cover is not closed.

• Close the cover correctly.

 

• When the LAMP indicator or the TEMP

• Contact your dealer.

 

indicator is either on or blinking, the main unit

 

 

requires repairs.

 

 

 

 

No picture appears

• Lens is covered by lens cap.

• Take the lens cap off.

on the screen.

• When the LAMP indicator or the TEMP

• Replace the lamp with a new one.

 

indicator is either on or blinking, the main unit

 

 

requires repairs.

 

 

• The equipment connected to this projector is not turned on.

• Turn on the connected equipment.

 

• Hookup is not made correctly with other equipment.

• Confirm the hookup.

 

• The input source is not selected correctly.

• Select the correct source according to the equip-

 

 

ment connected to this projector.

 

 

 

The image is

• The air inlet slots, outlet slots or air filter is

• Remove the object and turn off the main power

clogged with dust or some objects.

switch. After about 10 minutes, Turn the pro-

turned off.

(In this case, the TEMP indicator does not light up.)

jector on.

 

 

 

 

The image is

• The projector is not at a right angle to the screen.

• Adjust the angle of the projector to make a right

distorted.

 

angle to the screen. See page 12.

 

 

 

The image is dark.

• Brightness, tint and color are not adjusted correctly.

• Adjust brightness, tint and color correctly.

The image is

• The projecting distance is beyond the focused area.

• Adjust the projecting distance. See page 9.

blurred.

• Lens is dirty.

• Clean lens.

 

• Screen size exceeds screen size specifications.

Reduce screen size to within 40" to 300".

 

• Brightness and contrast are not adjusted correctly.

• Adjust brightness, contrast.

 

• FINE adjustment is not made correctly.

• Make FINE adjustment.

 

• Tracking is not adjusted.

• Adjust tracking.

 

• The projector is not at a right angle to the screen.

• Adjust the angle of the projector to make a

 

 

right angle to the screen. See page 12.

 

 

 

The afterimage

• When a stationary image is projected for a long

time, its afterimage may persist on the screen. This

remains.

is not a failure, and the afterimage will disappear in a few minutes.

Red, blue or green dots are

• It is normal.

 

viewed on the text of image.

 

 

The image is dis-

• The cable for connection with other equipment

• Plug the connecting cable securely into the

torted on the screen

is not plugged securely into the terminal.

terminal. See pages 10-11.

and noise is heard.

• The projector is installed too close to other

• Install the projector far away from other equipment.

 

equipment.

 

No sound is heard.

• Volume is not turned up.

• Turn up the volume.

 

• Connection to other equipment is not made correctly.

• Check connections. See pages 10-11.

Nothing is displayed on

• The PC monitor is not turned on.

• Turn on the monitor.

the PC monitor.

 

Warm air comes out of

• This is typical of the LCD projector.

 

the exhaust vents.

 

 

Adjustments cannot be

• The operation is incorrectly made due to noise or

• Press the reset button on the Terminal board.

interference.

See page 15.

made.

 

 

is displayed.

• This mark is displayed when an invalid operation

is executed (for example, when the COMPUTER or

 

VIDEO button is pressed while the menu is displayed). This is not failure.

 

 

 

EN – 24

Image 24
Contents 3 0 X L 2 5 S L 2 When using the projector in Europe Compliance NoticeContents Important safeguards Compliance Notice of Industry Canada Overview Control panel Rear panelBottom side Remote control About the laser beamUsing the remote control Battery installationOperation area for wireless control system Using the wired remote controlInstallation Orientation of the projectorScreen Basic connections Projector + AV deviceProjector + DVD player or Hdtv decoder For the computer with a Mini D-SUB 15P connectors For using the COMPUTER/COMPONENT Video in 2 BNC terminalsProjector + Computer For MacintoshAdjusting the angle of projection Preparing the projector for operationGetting ready for projection To operate projector power on Lamp PowerVolume from the speaker Anamorphic modeHow to use the installed functions Turning off the projectorMenu operation Basic operationGreatly, select 3.When you select OFF, RIS won’t operate When the sensitivity is adjusted in a large amount,Image may be displayed solid white. Adjust the sensitivity Depending on the operating environment and imges to beFeature Picture adjustment User memory for signal settingAdjusting the image Color matrixColor temperature Adjustment from personal computerAdvanced features for presentation ExpandPicture in Picture PinP StillMouse remote control Projector + computer with USB connectorProjector + computer with PS/2 connector OperationLamp replacement Interval of the lamp replacementHow to reset the operation time meter Maintenance Cleaning the air-filterCleaning the projector and the ventilation slots Cleaning the lensTroubleshooting Problems Cause Possible SolutionsIndicators Normal conditionAbnormal condition Specifications Connectors Dimensional drawingsReplacement part Option / Not included in the box What’s included in the boxSpecifications 59.94 800 x TV50 Control command diagram InterfacePC-controllable functions ConnectionOperation commands How to set the gradeControl sequence Remote commands Reading command diagramWhen sRGB is ON, only the main data are effective How to set the grade