Mitsubishi Electronics XL30 XL25 SL25 user manual How to set the grade

Page 34

How to set the grade

Use the ASCII codes to set the grade for setting data. Please refer to the table below for the HEX code.

ASCII

'+'

'–'

'0'

'1'

'2'

'3'

'4'

'5'

'6'

'7'

'8'

'9'

HEX

2Bh

2Dh

30h

31h

32h

33h

34h

35h

36h

37h

38h

39h

[Example 1] When setting the AUTO POWER ON to ON. (Figures and symbols enclosed in quotation marks are ASCII codes.):

Sending commands

Status code from

Description

from the PC, etc.

the projector

 

30 30 41 50 4F 4E 31 0D

 

Command for setting the

'0' '0' 'A' 'P' 'O' 'N' '1' ' '

 

AUTO POWER ON to ON

 

 

 

 

30 30 41 50 4F 4E 31 0D

Command receipt confirmation

 

'0' '0' 'A' 'P' 'O' 'N' '1' ' '

(Command echo back)

 

 

 

The data code of CONTRAST and BRIGHTNESS consists of the difference data between R and G, the main data, and the difference data between B and G.

[Example 2] When setting the difference data between R and G to +10, the main data to 0, and the difference data between B and G to -5. (Figures and symbols enclosed in quotation marks are ASCII codes.):

Sending commands

 

Status code from

Description

from the PC, etc.

 

the projector

 

30 30 50 2B 31 30 2B 30 30 2D 30 35 0D

 

Command for setting the

'0' '0' 'P' '+' '1' '0' '+' '0' '0' '-' '0' '5' '

'

 

picture control

 

 

 

 

 

 

30 30 50 2B 31 30 2B 30 30 2D 30 35 0D

Command receipt confirmation

 

 

'0' '0' 'P' '+' '1' '0' '+' '0' '0' '-' '0' '5' ' '

(Command echo back)

 

 

 

 

[Example 3] When checking the TINT setting (when the TINT is set to +10). (Figures and symbols enclosed in quotation marks are ASCII codes.)::

Sending commands

Status code from

Description

from the PC, etc.

the projector

 

30 30 53 0D

 

Command for checking

'0' '0' 'S' ' '

 

the TINT setting

 

 

 

 

30 30 53 2B 31 30 0D

Check result (+10)

 

'0' '0' 'S' '+' '1' '0' ' '

 

 

 

 

5

Image 34
Contents 3 0 X L 2 5 S L 2 When using the projector in Europe Compliance NoticeContents Important safeguards Compliance Notice of Industry Canada Overview Control panel Rear panelBottom side Remote control About the laser beamOperation area for wireless control system Using the remote controlBattery installation Using the wired remote controlOrientation of the projector InstallationScreen Projector + AV device Basic connectionsProjector + DVD player or Hdtv decoder Projector + Computer For the computer with a Mini D-SUB 15P connectorsFor using the COMPUTER/COMPONENT Video in 2 BNC terminals For MacintoshPreparing the projector for operation Adjusting the angle of projectionGetting ready for projection To operate projector power on Lamp PowerHow to use the installed functions Volume from the speakerAnamorphic mode Turning off the projectorMenu operation Basic operationImage may be displayed solid white. Adjust the sensitivity Greatly, select 3.When you select OFF, RIS won’t operateWhen the sensitivity is adjusted in a large amount, Depending on the operating environment and imges to beFeature Adjusting the image Picture adjustmentUser memory for signal setting Color matrixColor temperature Adjustment from personal computerPicture in Picture PinP Advanced features for presentationExpand StillProjector + computer with PS/2 connector Mouse remote controlProjector + computer with USB connector OperationInterval of the lamp replacement Lamp replacementHow to reset the operation time meter Cleaning the projector and the ventilation slots MaintenanceCleaning the air-filter Cleaning the lensTroubleshooting Problems Cause Possible SolutionsNormal condition IndicatorsAbnormal condition Specifications Replacement part Option / Not included in the box ConnectorsDimensional drawings What’s included in the boxSpecifications 59.94 800 x TV50 PC-controllable functions Control command diagramInterface ConnectionHow to set the grade Operation commandsControl sequence Remote commands Reading command diagramWhen sRGB is ON, only the main data are effective How to set the grade