Mitsubishi Electronics XL30 XL25 SL25 user manual Indicators, Normal condition, Abnormal condition

Page 25

Indicators

The projector has three indicators each of which shows the working condition of the projector.

The following offers solutions to possible problems. If a problem persists, turn the projector off and consult your dealer.

TEMP indicator

LAMP indicator

POWER indicator

ENGLISH

Normal condition

POWER LAMP

TEMP CONDITION

Notes

Steady

Off

Stand-by

 

Off

 

red

 

 

 

 

 

Lamp stand-by (about for 1 minute)

The power button cannot be used to switch

Steady

Blinking

Off

OFF.

green

green

 

 

 

The POWER is ON. (Normal condition)

 

Steady

Steady

Off

 

green

green

 

 

Abnormal condition

POWER LAMP

TEMP

Steady

Steady

Blinking

green

green

red

Steady

Off

Blinking

red

 

red

CONDITION

POSSIBLE SOLUTIONS

Unusual temperature

• Remove the object from the ventilation

• The ventilation slits or air filter is clogged with

dust or debris.

slits.

• The room temperature is too high.

• Relocate the projector to a cooler place.

• The filter is dirty.

• Clean the filter.

 

 

 

 

 

 

 

The protection circuit is working or the lamp is in an

 

 

 

 

 

 

 

Steady

Blinking

Off

abnormal condition.

(The indicators operate as shown on the left at the time of power-off, too.

red

green

 

 

 

 

 

 

 

 

In this case, they are’nt indicating an abnormal condition.)

Wait until the LAMP indicator is turned off, then press the POWER button.

If the above operation is not effective, replace the lamp.

Lamp duration warning. (Lightning duration total

Steady Blinking Off about 1, 000 hours*.When the POWER is ON.)

green green/red

 

 

 

 

Off

Lamp duration warning. (Lightning duration total

Steady

Blinking

about 1, 000 hours*.When the POWER is OFF.)

red

red

 

Replace the lamp.

Exchange with a new lamp if the same problem recurs.

Steady

Steady

Off

Lamp duration warning. (Lightning duration total

 

about 1,500 hours*.)

 

red

red

 

 

 

 

 

The lamp or filter cover is not closed.

Close the cover correctly.

Blinking

Off

Off

 

 

green/red

 

 

 

 

 

Steady

Steady

Abnormal.

Contact your dealer.

 

 

 

Blinking

or

or

 

 

 

 

 

 

green/red

 

 

 

 

 

Blinking

Blinking

 

 

*) When LAMP MODE of the INSTALLATION menu is set to STANDARD.When it is set to LOW, the duration will be extended.

EN – 25

Image 25
Contents 3 0 X L 2 5 S L 2 Compliance Notice When using the projector in EuropeContents Important safeguards Compliance Notice of Industry Canada Control panel Rear panel OverviewAbout the laser beam Bottom side Remote controlBattery installation Using the remote controlOperation area for wireless control system Using the wired remote controlOrientation of the projector InstallationScreen Projector + AV device Basic connectionsProjector + DVD player or Hdtv decoder For using the COMPUTER/COMPONENT Video in 2 BNC terminals For the computer with a Mini D-SUB 15P connectorsProjector + Computer For MacintoshPreparing the projector for operation Adjusting the angle of projectionGetting ready for projection Lamp Power To operate projector power onAnamorphic mode Volume from the speakerHow to use the installed functions Turning off the projectorBasic operation Menu operationWhen the sensitivity is adjusted in a large amount, Greatly, select 3.When you select OFF, RIS won’t operateImage may be displayed solid white. Adjust the sensitivity Depending on the operating environment and imges to beFeature User memory for signal setting Picture adjustmentAdjusting the image Color matrixAdjustment from personal computer Color temperatureExpand Advanced features for presentationPicture in Picture PinP StillProjector + computer with USB connector Mouse remote controlProjector + computer with PS/2 connector OperationInterval of the lamp replacement Lamp replacementHow to reset the operation time meter Cleaning the air-filter MaintenanceCleaning the projector and the ventilation slots Cleaning the lensProblems Cause Possible Solutions TroubleshootingNormal condition IndicatorsAbnormal condition Specifications Dimensional drawings ConnectorsReplacement part Option / Not included in the box What’s included in the boxSpecifications 59.94 800 x TV50 Interface Control command diagramPC-controllable functions ConnectionHow to set the grade Operation commandsControl sequence Reading command diagram Remote commandsWhen sRGB is ON, only the main data are effective How to set the grade