Mitsubishi Electronics XL30 XL25 SL25 user manual Interface, Control command diagram, Connection

Page 30

LCD Projector

XL30U / XL25U / SL25U

This projector can be controlled by connecting a personal computer with RS-232C terminal.

PC-controllable functions :

Turning the power ON or OFF

Changing input signals

Inputting commands by pressing the buttons on the control panel and remote control

Menu setting

Connection

RS-232C cable

to Com1 Comport

to RS-232C terminal

D-SUB 9P

Mini DIN 8P

Important:

Make sure that your computer and projector are turned off before connection.

Turn on the projector after the computer is started up.

(If you do not follow this instruction, the Comport may not function.)

Adapters may be necessary depending on the PC connected to this projector. Contact your dealer for details.

1) Interface

PROTOCOL

RS-232C

BAUD RATE

9600 [bps]

DATA LENGTH

8 [bits]

PARITY BIT

NONE

STOP BIT

1 [bit]

FLOW CONTROL

NONE

This projector uses RXD, TXD and GND lines for RS-232C control.

For RS-232C cable,the reverse type cable should be used.

2) Control command diagram

The command consists of the address code, function code, data code, and end code. The length of the command varies among the functions.

 

 

Address code

Function code

 

Data code

End code

 

 

 

 

 

 

 

 

 

 

 

HEX

 

30h 30h

Function

 

Data

0Dh

 

 

ASCII

 

'0' '0'

Function

 

Data

 

 

[Address code]

30h 30h (In ASCII code, '0' '0') fixed.

 

 

 

[Function code] A code of each fixed control move.

 

 

 

[Data code]

A code of each fixed control data (number) and not always indicated.

[End code]

0Dh (In ASCII code, ' ') fixed.

 

 

 

1

Image 30
Contents 3 0 X L 2 5 S L 2 When using the projector in Europe Compliance NoticeContents Important safeguards Compliance Notice of Industry Canada Overview Control panel Rear panelBottom side Remote control About the laser beamOperation area for wireless control system Using the remote controlBattery installation Using the wired remote controlInstallation Orientation of the projectorScreen Basic connections Projector + AV deviceProjector + DVD player or Hdtv decoder Projector + Computer For the computer with a Mini D-SUB 15P connectorsFor using the COMPUTER/COMPONENT Video in 2 BNC terminals For MacintoshAdjusting the angle of projection Preparing the projector for operationGetting ready for projection To operate projector power on Lamp PowerHow to use the installed functions Volume from the speakerAnamorphic mode Turning off the projectorMenu operation Basic operationImage may be displayed solid white. Adjust the sensitivity Greatly, select 3.When you select OFF, RIS won’t operateWhen the sensitivity is adjusted in a large amount, Depending on the operating environment and imges to beFeature Adjusting the image Picture adjustmentUser memory for signal setting Color matrixColor temperature Adjustment from personal computerPicture in Picture PinP Advanced features for presentationExpand StillProjector + computer with PS/2 connector Mouse remote controlProjector + computer with USB connector OperationLamp replacement Interval of the lamp replacementHow to reset the operation time meter Cleaning the projector and the ventilation slots MaintenanceCleaning the air-filter Cleaning the lensTroubleshooting Problems Cause Possible SolutionsIndicators Normal conditionAbnormal condition Specifications Replacement part Option / Not included in the box ConnectorsDimensional drawings What’s included in the boxSpecifications 59.94 800 x TV50 PC-controllable functions Control command diagramInterface ConnectionOperation commands How to set the gradeControl sequence Remote commands Reading command diagramWhen sRGB is ON, only the main data are effective How to set the grade