Mitsubishi Electronics XL30 XL25 SL25 user manual Compliance Notice of Industry Canada

Page 5

WARNING:

Unplug immediately if there is something wrong with your projector.

Do not operate if smoke, strange noise or odor comes out of your projector. It might cause fire or electric shock. In this case, unplug immediately and contact your dealer.

Never remove the cabinet.

This projector contains high voltage circuitry. An inadvertent contact may result in an electric shock. Except as specifically explained in the Owner's Guide, do not attempt to service this product yourself. Please contact your dealer when you want to fix, adjust or inspect the projector.

Do not modify this equipment.

It can lead to fire or electric shock.

If you break or drop the cabinet.

Do not keep using this equipment if you break or drop it. Unplug the projector and contact your dealer for inspection. It may lead to fire if you keep using the equipment.

Do not face the projector lens to the sun.

It can lead to fire.

Use correct voltage.

If you use incorrect voltage, it can lead to fire.

Do not place the projector on uneven surface.

Place the projection on a leveled and stable surface only. Please do not place equipment on unstable surfaces.

Do not look into the lens when it is operating.

It may hurt your eyes.Never let children look into the lens when it is on.

Do not turn off the main power abruptly or unplug the projector during operation.

It can lead to lamp breakage, fire, electric shock or other trouble. It is best to wait for the fan to turn off before turning main power off.

Do not touch Air outlet grille and Bottom plate which becomes hot.

Do not touch them or put other equipment in front of Air outlet grille. The heated Air outlet grille and Bot- tom plate may cause injury or damage to other equip- ment. Also, do not set the projector on the desk which is easily affected by heat.

Clean the air-filter once a month.

Clean the air-filter frequently. If the filter or ventila- tion slots become clogged with dirt or dust, the tem- perature inside of the projector may rise and cause some troubles, such as damage of inside parts, and shortening the life of panel.

Do not look into the air outlet grille when projector is operating.

Heat, dust etc. may blow out of it and hurt your eyes.

Place of installation

For safety’s sake, refrain from setting the projector at any place subjected to high temperature and high humidity. Please maintain an operating temperature, humidity, and altitude as specified below.

Operating temperature: between +41° F (+5° C) and +95° F (+35° C)

Operating humidity: between 30 and 90%

Never put any heat-producing device under the pro- jector so that the projector does not overheat.

Do not attach the projector to a place that is un- stable or subject to vibration.

Do not install the projector near any equipment that produces a strong magnetic field. Also refrain from installing near the projector any cable carrying a large current.

Place the projector on a solid, vibration free sur- face: otherwise it may fall, causing serious injury to a child or adult, and serious damage to the prod- uct.

Do not stand the projector: it may fall, causing se- rious injury and damage to the projector.

Slanting the projector more than ± 15˚(right and left or front and rear) may cause trouble or explosion of the lamp.

Do not place the projector near air-conditioning unit or heater to avoid hot air to the exhaust and venti- lation hole of the projector.

ENGLISH

COMPLIANCE NOTICE OF FCC

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver.

Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

Consult the dealer or an experienced radio / TV technician for help.

Changes or modifications not expressly approved by Mitsubishi could void the user's authority to operate this equipment.

COMPLIANCE NOTICE OF INDUSTRY CANADA

This Class B digital apparatus complies with Canadian ICES-003.

EN – 5

Image 5
Contents 3 0 X L 2 5 S L 2 Compliance Notice When using the projector in EuropeContents Important safeguards Compliance Notice of Industry Canada Control panel Rear panel OverviewAbout the laser beam Bottom side Remote controlBattery installation Using the remote controlOperation area for wireless control system Using the wired remote controlScreen InstallationOrientation of the projector Projector + DVD player or Hdtv decoder Basic connectionsProjector + AV device For using the COMPUTER/COMPONENT Video in 2 BNC terminals For the computer with a Mini D-SUB 15P connectorsProjector + Computer For MacintoshGetting ready for projection Adjusting the angle of projectionPreparing the projector for operation Lamp Power To operate projector power onAnamorphic mode Volume from the speakerHow to use the installed functions Turning off the projectorBasic operation Menu operationWhen the sensitivity is adjusted in a large amount, Greatly, select 3.When you select OFF, RIS won’t operateImage may be displayed solid white. Adjust the sensitivity Depending on the operating environment and imges to beFeature User memory for signal setting Picture adjustmentAdjusting the image Color matrixAdjustment from personal computer Color temperatureExpand Advanced features for presentationPicture in Picture PinP StillProjector + computer with USB connector Mouse remote controlProjector + computer with PS/2 connector OperationHow to reset the operation time meter Lamp replacementInterval of the lamp replacement Cleaning the air-filter MaintenanceCleaning the projector and the ventilation slots Cleaning the lensProblems Cause Possible Solutions TroubleshootingAbnormal condition IndicatorsNormal condition Specifications Dimensional drawings ConnectorsReplacement part Option / Not included in the box What’s included in the boxSpecifications 59.94 800 x TV50 Interface Control command diagramPC-controllable functions ConnectionControl sequence Operation commandsHow to set the grade Reading command diagram Remote commandsWhen sRGB is ON, only the main data are effective How to set the grade