Nokia CC100 manual Features, Glossary

Page 4

CC100 Master Bridge User’s Guide

1

INTRODUCTION

This chapter describes the features of your HomePNA3.1 over Coax MDU Master Bridge -- CC100. Refer to “HomePNA3.1 over Coax” as HCNA from this point.

Features

One HCNA port for driving HomePNA3.1 signal into existing coaxial cable

One TV/Antenna port for TV set connection or for TV signal from VHF/UHF antenna/CATV

Two fast Ethernet ports with Auto-Detect MDIX Function(Auto Crossover) and Auto-Negotiating Half/Full Duplex 10M/100M for expansion or link to FTTx/xDSL Modem

One reset button

Priority queue based QoS support for 802.1p, IP TOS, UDP/TCP protocols

Support for up to 31 end point (Endpoint, as CC101 Slave Unit) concurrent connections

Built-in diagnostic function for individual end point connection

Built-in web server and telnet server to support remote configuration via web browser or telnet protocol

Supports remote HTTP/TFTP upgrade function for system firmware and HCNA driver

Supports HCNA driver upgrade on-line for connected end points

Supports SNMP function

Glossary

HCNA

HomePNA3.1 over coaxial cable

MDU

Multiple Dwelling Unit

Coax

Coaxial cable

SyncMode

HCNA device operates in Synchronous mode

AsyncMode

HCNA device operates in Asynchronous mode

Master

Master HCNA device in one coax network

Slave

Slave HCNA device in one coax network

EP

Endpoint, equivalent to Slave HCNA device, CC101

Smart EP

Smart Endpoint, as CC101. CC100 could configure Smart EP’s Ethernet properties.

QoS

Quality of Service

Mixer

Coax device sums two or more signals into one

Splitter

Coax device divides a signal into two or more smaller and approximately equal signals.

Combiner

Coax device adds several discrete signal inputs to one and has high isolation between inputs

Duplexer

Coax device separates 2 signals within the same band

Diplexer

Coax device separates 2 signals in different bands

Tap

Coax device uses for matching impedance or connecting subscriber drops

dB

Decibel, to express either a gain or loss power ration(log) after the signal has been transmitted

1

Image 4
Contents User Guide Vcci & CE Table of Contents Features GlossaryConnectors LED IndicatorsPacking List Rear PanelConnecting the Cables Detailed cabling of CC100Verification Different Cabling of CC100Installing the CC100 with an amplifier Configuration Methods Use Web BrowserSystem Assets Information System Setup TCP/IP PropertiesEP User Management EP Management Architecture Firmware/Driver FilesMAC Properties Profile Stored the Settings Master HomePNA Properties HpnaCC100 Master Bridge User’s Guide Privacy Mode/Key Summary Profile Status for Master and EP EP HomePNA Properties HpnaMaster/Smart EP Ethernet Properties Ether EP Downstream Igmp v2 Snooping Setup CC100 Master Bridge User’s Guide Delete the Obsolete EP Profile DiagnosisPhysical Connection between Master and EP Administration Administrator Allowed SourceCC100Master Bridge User’s Guide Telnet/Http/SNMP Setup Alert Critical Error Info System LogSystem Time Static MACReboot System Default SettingBackup/Restore Configuration Upload FirmwareNew System Firmware and Hcna Driver Files System FirmwareCC100Master Bridge User’s Guide CC100 Master Bridge User’s Guide CC100Master Bridge User’s Guide Check the New System Firmware in ‘Upload Area’ Activate the New System Firmware Hcna Driver CC100Master Bridge User’s Guide Also shown on ‘EP Management’ window ‘Upload Area’ Master/EP runs the New Hcna Driver System Firmware and Hcna Driver Version after Upgrade Use Telnet Command Sets for Telnet Console DescriptionDconfig DefaultEphpnareboot DiagAllow/deny Hpnareboot IpconfigReboot ServiceCC100 Master Bridge User’s Guide Snmptrapsetup SwconfigSnmptrapserver SntpSwtagvlan TftpTime UpepUse Snmp CC100 Master Bridge User’s Guide QoS Priority in Upstream and Downstream802.1p TCP/UDP Port NumberSpecifications A N M I S S I O N S P E E D a N D R a N G E R M I N a L D E V I C E S E N D P O I N TLegal & Regulatory Information GNU General Public License Product Warranty Technical Support