Nokia CC100 manual Legal & Regulatory Information

Page 54

CC100 Master Bridge User’s Guide

Legal & Regulatory Information

This manual is copyright. Apart from any fair dealing for the purposes of private study, research, criticism or review, as permitted under the Copyright Act, no part may be reproduced, stored in a retrieval system or transmitted in any form, by any means, be it electronic, mechanical, recording or otherwise, without the prior written permission of NetComm Limited. NetComm Limited accepts no liability or responsibility, for consequences arising from the use of this product.

NetComm Limited reserves the right to change the specifications and operating details of this product without notice.

NetComm is a registered trademark of NetComm Limited.

All other trademarks are acknowledged the property of their respective owners.

Customer Information

ACA (Australian Communications Authority) requires you to be aware of the following information and warnings:

(1)This unit shall be connected to the Telecommunication Network through a line cord which meets the requirements of the ACA TS008 Standard.

(2)This equipment has been tested and found to comply with the Standards for C-Tick and or A-Tick as set by the ACA . These standards are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio noise and, if not installed and used in accordance with the instructions detailed within this manual, may cause interference to radio communications. However, there is no guarantee that interference will not occur with the installation of this product in your home or office. If this equipment does cause some degree of interference to radio or television reception, which can be determined by turning the equipment off and on, we encourage the user to try to correct the interference by one or more of the following measures:

Change the direction or relocate the receiving antenna.

Increase the separation between this equipment and the receiver.

Connect the equipment to an alternate power outlet on a different power circuit from that to which the receiver/TV is connected.

Consult an experienced radio/TV technician for help.

(3)The power supply that is provided with this unit is only intended for use with this product. Do not use this power supply with any other product or do not use any other power supply that is not approved for use with this product by NetComm. Failure to do so may cause damage to this product, fire or result in personal injury.

51

Image 54
Contents User Guide Vcci & CE Table of Contents Features GlossaryPacking List ConnectorsLED Indicators Rear PanelConnecting the Cables Detailed cabling of CC100Verification Different Cabling of CC100Installing the CC100 with an amplifier Configuration Methods Use Web BrowserSystem Setup TCP/IP Properties System Assets InformationEP User Management EP Management Architecture Firmware/Driver FilesMAC Properties Profile Stored the Settings Master HomePNA Properties HpnaCC100 Master Bridge User’s Guide Privacy Mode/Key Summary Profile Status for Master and EP EP HomePNA Properties HpnaMaster/Smart EP Ethernet Properties Ether EP Downstream Igmp v2 Snooping Setup CC100 Master Bridge User’s Guide Delete the Obsolete EP Profile DiagnosisPhysical Connection between Master and EP Administration Administrator Allowed SourceCC100Master Bridge User’s Guide Telnet/Http/SNMP Setup Alert Critical Error Info System LogSystem Time Static MACBackup/Restore Configuration Reboot SystemDefault Setting Upload FirmwareNew System Firmware and Hcna Driver Files System FirmwareCC100Master Bridge User’s Guide CC100 Master Bridge User’s Guide CC100Master Bridge User’s Guide Check the New System Firmware in ‘Upload Area’ Activate the New System Firmware Hcna Driver CC100Master Bridge User’s Guide Also shown on ‘EP Management’ window ‘Upload Area’ Master/EP runs the New Hcna Driver System Firmware and Hcna Driver Version after Upgrade Use Telnet Command Sets for Telnet Console DescriptionEphpnareboot DconfigDefault DiagAllow/deny Reboot HpnarebootIpconfig ServiceCC100 Master Bridge User’s Guide Snmptrapserver SnmptrapsetupSwconfig SntpTime SwtagvlanTftp UpepUse Snmp CC100 Master Bridge User’s Guide 802.1p QoSPriority in Upstream and Downstream TCP/UDP Port NumberSpecifications A N M I S S I O N S P E E D a N D R a N G E R M I N a L D E V I C E S E N D P O I N TLegal & Regulatory Information GNU General Public License Product Warranty Technical Support