Garmin HN294DP/DI manual ADSL-mode - RFC1483 Router, Description, IP Addresses Assigned by DHCP

Page 28

5 ADSL-mode – RFC1483 Router

ADSL-mode – RFC1483 Router

5 ADSL-mode – RFC1483 Router

5.1Description

RFC1483 (2684) Routed Mode (single PVC)

The RFC1483 Router mode allows a simple routed connection to the Internet. This ADSL-mode can also be used together with NAT to let the end-user connect an almost unlimited number of PCs on the LAN/WLAN with only one IP address from the ISP.

NOTE! The HN294d supports RFC1483 Routed mode with static IP addresses or with DHCP IP addresses assignment to the WAN interface. No standard exists for DHCP over a RFC1483 Routed connection, meaning this is a proprietary solution.

The built-in DHCP client will provide the built-in DHCP server with information so that no configuration is needed of the built-in DHCP server (DNS information etc is filled in automatically). PCs on the LAN/WLAN will be assigned private IP addresses from the built-in DHCP server and the NAT service will route the traffic to/from the WAN. All traffic from the LAN/WLAN uses the same PVC (as in the normal ISP scenario).

5.2IP Addresses Assigned by DHCP

The PCs on the LAN/WLAN normally use the DHCP protocol. The IP addresses are dynamically assigned to the PCs from the DHCP server in the HN294d. If DHCP Relay is enabled, the IP addresses can be assigned from a DHCP server at the ISP. Verify that your TCP/IP settings are set to

22	EN/LZT 108 6377 R4 - September 2003

Image 28

Contents HN294dp/di ADSL Wireless RouterUser Guide Copyright DisclaimerAbstract Trademark ListContents Hardware Description and InstallationInitial Configuration IntroductionAdvanced Configuration ADSL-mode - RFC1483 RouterADSL-mode - RFC1483 MER Router ADSL-mode - PPPoE RouterTroubleshooting Important InformationGlossary 1 Introduction 1.2 About the ADSL Wireless Router HN294d1.1 About this User Guide 1.2.2 Wireless Features 1.2.1 Ease of Use1.2.3 Security 1.2.4 Advanced Possibilities Hardware Description and Installation 2.1.1 Package Contents2.1 Before You Start Figure 1 - HN294d Package Contents2.1.2 Subscription for ADSL Service 2.2.1 Front Panel and LED Indicators2.2 Physical Appearance SymbolTable 1 - Description of LEDs 2.2.2 Back Panel and ConnectorsFigure 2 - Back Panel of the HN294d 2.3 Choose a Place for the Router Figure 3 - Wall mounting of the HN294d2.4.1 Connect Wireless Computers 2.4 Connect the HN294d3. Connect the Power Supply 4. Power ON the HN294d2.4.2 Connect Computers via Cables 1. Connect the ADSL Line2. Connect a client PC to one of the four LAN ports OR to the USB port2.4.2.1 Install USB Drivers 3. Select Install USB Driver and wait until the following window is displayed 7. Click Finish to close the InstallShield wizard 2.5 Configure Client PCs 2.5.1 Use DHCPIn Windows 98/98SE and Me In Windows2.5.2 Use Static IP Addresses In Windows XPIn Windows Initial Configuration 3.1 IntroductionConnection Type Select ADSL-mode3.2 Access the Configuration Wizard 3.3 Access the Internet 4 ADSL-mode - RFC1483 Bridge 4.1 Description4.2 IP Addresses Assigned by PPPoE RFC1483 2684 Bridged Mode single PVC4.3 IP Addresses Assigned by DHCP 4.4 Static IP Addresses5 ADSL-mode - RFC1483 Router 5.1 Description5.2 IP Addresses Assigned by DHCP RFC1483 2684 Routed Mode single PVC5.3 Static IP Addresses 6 ADSL-mode - RFC1483 MER Router 6.1 Description6.2 IP Addresses Assigned by DHCP 7 ADSL-mode - PPPoE Router 7.1 Description7.2 PPPoE Termination and PPPoE Passthrough 7.3 IP Addresses Assigned by DHCP8 ADSL-mode - PPPoA Router 8.1 Description8.2 IP Addresses Assigned by DHCP 9.2 Access the Web Manager Advanced Configuration9.1 Introduction 9.2.1 Outline of the Web Manager 9.3 Overview 9.3.1 Connect/Disconnect to ISPDisconnect 9.4.2 Administration 9.4 System9.4.1 Device Information 9.4.2.1 Account9.4.2.2 Remote Management 9.4.3 Backup Configuration 9.4.2.3 Web Port9.4.3.1 Backup 9.4.3.2 Restore9.4.4 Save Configuration 9.4.5 Upgrade Firmware9.4.6 Reset Router 9.4.6.1 Reset to Factory Default 9.5.1 DSL Connection 9.5 StatusParameter 9.5.2 WAN Connection 9.5.3 Traffic Counter 9.5.4 Routing Table 9.5.6 Wireless Client9.5.5 DHCP Table Advanced Configuration 9.6.1 DSL Configuration 9.6 Configuration9.6.2 LAN Configuration Enter your IP settings and click the Apply button 9.6.2.1 IP AddressThe table below describes the parameters 192.168.0.1 and 255.255.255.0 respectively. ThisEnable and configure the DHCP server 9.6.2.2 DHCP ServerInterface Start IP Address End IP Address DHCP lease time Enable and configure the DHCP Relay Agent Domain Name Servers9.6.3 WLAN Configuration 9.6.3.1 Basic SetupWireless SSID Set the Wired Equivalent Privacy Mechanism to ON 9.6.3.2 Association Control Add / Remove client 9.6.4 WAN Configuration Create a new ATM PVC Interfaceselected IP Configuration PPP Configuration9.6.5 IP Route 9.6.5.1 Static Route9.6.5.2 Dynamic Routing Destination Address and Netmask9.6.6 DNS 9.6.6.1 DNS RelayTo enable DNS Relay or modify the current settings proceed as follows 9.6.6.2 DNS Server 9.6.7 Security 9.6.7.1 FirewallAdvanced Configuration Modify or delete existing rules 3. Click the Modify link next to the rule you want to modify Description of parameters when creating a new filtering rule On the Configuration Security Intrusion Detection you can enable/disable the intrusion detection function and also see and modify the existing rules 9.6.7.2 Intrusion Detection9.6.8 Virtual Server Create a new virtual server External Packet Create a DMZ zoneInternal Host 9.6.9 IGMP Proxy 9.6.10 UPnP 10 Troubleshooting 10.1 Basic FunctionsLAN Connection Indication/Symptom10.2.1 How to use WINIPCFG 10.2.2 How to use IPCONFIG10.4 WLAN Connection 10.3 WAN ConnectionStart Run… type command and click OK . In the 10.5 Reset the HN294d 10.6 Safety Mode4. Click the Upgrade button 11.1 Product Care and Maintenance 11 Important Information11.2.3 Limited Warranty 11.2 License Agreement11.2.1 License 11.2.2 Term11.2.5 Limitation of Liability 11.2.4 Intended Use11.2.6 Governing Law 11.3.2 Safety Approvals 11.3 Regulatory Information11.3.1 EU Directives 11.3.1.1 Declaration of Conformity11.3.3 EMC Approvals 11.3.2.1 UL 1950 Statement11.3.3.1 FCC Part 15 Statement 11.3.4 Telecom Approval11.3.3.2 FCC RF Radiation Exposure Statement 11.3.4.1 FCC Part 68 Statement 11.3.5 Access Point Frequency Band 11.3.7 Power Supply11.3.6 Caution 11.3.8 Environmental InformationGlossary Access PointADSL AsynchronousDevice DHCPDomain name DOS attackDownstream DSLAMEncapsulation EthernetFirewall FirmwareG.lite HostHTTP IEEEIP address IntranetMAC address Peer-to-peer PingPort POTSSMTP RouterSSID Stateful Inspection T1.413TCP/IP TelnetUpstream UPnPVirtual Server VPI and VCI WLAN