Garmin HN294DP/DI manual Reset the HN294d, Safety Mode

Page 84

10.5Reset the HN294d

Troubleshooting

Bluetooth devices, microwave ovens and 2.4 GHz cordless phones might interfere with your wireless LAN.

Furthermore, you may want to consider repositioning the HN294d (e.g. wall mount it).

10.5Reset the HN294d

Failure to access your HN294d may occur if the router is configured incorrectly or if you simply forget your login Username and Password. You may end up in a situation where restoring the original default settings is the only option.

The following procedure will reset ALL configurable values back to their original default, including the login Username and Password.

1.Make sure your HN294d is turned On.

2.By using the tip of a pen, press the Reset button (tiny hole) to the left of the power switch at the back of the HN294d.

3.Keep the button pressed for at least 10 seconds before releasing it.

4.The HN294d will reboot and comes then online with factory default settings.

10.6Safety Mode

The HN294d is equipped with a special Safety Mode that is used only if a software upgrade fails. In case that an upgrade fails, all LEDs will lit and the Web Manager is not accessible.

Follow the steps below to access the router again and to make a new upgrade:

1.Your computer must be set to static IP address (within the range 192.168.0.2 to 192.168.0.253) and subnet mask 255.255.255.0.

2.Start your web browser and type 192.168.0.1 (the private IP address for the HN294d) in the URL field. The following page appears:

78	EN/LZT 108 6377 R4 - September 2003

Image 84

Contents ADSL Wireless Router HN294dp/diUser Guide Copyright DisclaimerAbstract Trademark ListContents Hardware Description and InstallationInitial Configuration IntroductionAdvanced Configuration ADSL-mode - RFC1483 RouterADSL-mode - RFC1483 MER Router ADSL-mode - PPPoE RouterTroubleshooting Important InformationGlossary 1.2 About the ADSL Wireless Router HN294d 1 Introduction1.1 About this User Guide 1.2.2 Wireless Features 1.2.1 Ease of Use1.2.3 Security 1.2.4 Advanced Possibilities Hardware Description and Installation 2.1.1 Package Contents2.1 Before You Start Figure 1 - HN294d Package Contents2.1.2 Subscription for ADSL Service 2.2.1 Front Panel and LED Indicators2.2 Physical Appearance Symbol2.2.2 Back Panel and Connectors Table 1 - Description of LEDsFigure 2 - Back Panel of the HN294d 2.3 Choose a Place for the Router Figure 3 - Wall mounting of the HN294d2.4.1 Connect Wireless Computers 2.4 Connect the HN294d3. Connect the Power Supply 4. Power ON the HN294d2.4.2 Connect Computers via Cables 1. Connect the ADSL Line2. Connect a client PC to one of the four LAN ports OR to the USB port2.4.2.1 Install USB Drivers 3. Select Install USB Driver and wait until the following window is displayed 7. Click Finish to close the InstallShield wizard 2.5 Configure Client PCs 2.5.1 Use DHCPIn Windows 98/98SE and Me In Windows2.5.2 Use Static IP Addresses In Windows XPIn Windows Initial Configuration 3.1 IntroductionConnection Type Select ADSL-mode3.2 Access the Configuration Wizard 3.3 Access the Internet 4 ADSL-mode - RFC1483 Bridge 4.1 Description4.2 IP Addresses Assigned by PPPoE RFC1483 2684 Bridged Mode single PVC4.3 IP Addresses Assigned by DHCP 4.4 Static IP Addresses5 ADSL-mode - RFC1483 Router 5.1 Description5.2 IP Addresses Assigned by DHCP RFC1483 2684 Routed Mode single PVC5.3 Static IP Addresses 6 ADSL-mode - RFC1483 MER Router 6.1 Description6.2 IP Addresses Assigned by DHCP 7 ADSL-mode - PPPoE Router 7.1 Description7.2 PPPoE Termination and PPPoE Passthrough 7.3 IP Addresses Assigned by DHCP8 ADSL-mode - PPPoA Router 8.1 Description8.2 IP Addresses Assigned by DHCP Advanced Configuration 9.2 Access the Web Manager9.1 Introduction 9.2.1 Outline of the Web Manager 9.3 Overview 9.3.1 Connect/Disconnect to ISPDisconnect 9.4.2 Administration 9.4 System9.4.1 Device Information 9.4.2.1 Account9.4.2.2 Remote Management 9.4.3 Backup Configuration 9.4.2.3 Web Port9.4.3.1 Backup 9.4.3.2 Restore9.4.4 Save Configuration 9.4.5 Upgrade Firmware9.4.6 Reset Router 9.4.6.1 Reset to Factory Default 9.5 Status 9.5.1 DSL ConnectionParameter 9.5.2 WAN Connection 9.5.3 Traffic Counter 9.5.6 Wireless Client 9.5.4 Routing Table9.5.5 DHCP Table Advanced Configuration 9.6 Configuration 9.6.1 DSL Configuration9.6.2 LAN Configuration Enter your IP settings and click the Apply button 9.6.2.1 IP AddressThe table below describes the parameters 192.168.0.1 and 255.255.255.0 respectively. ThisEnable and configure the DHCP server 9.6.2.2 DHCP ServerInterface Start IP Address End IP Address DHCP lease time Enable and configure the DHCP Relay Agent Domain Name Servers9.6.3 WLAN Configuration 9.6.3.1 Basic SetupWireless SSID Set the Wired Equivalent Privacy Mechanism to ON 9.6.3.2 Association Control Add / Remove client 9.6.4 WAN Configuration Create a new ATM PVC Interfaceselected IP Configuration PPP Configuration9.6.5 IP Route 9.6.5.1 Static Route9.6.5.2 Dynamic Routing Destination Address and Netmask9.6.6 DNS 9.6.6.1 DNS RelayTo enable DNS Relay or modify the current settings proceed as follows 9.6.6.2 DNS Server 9.6.7 Security 9.6.7.1 FirewallAdvanced Configuration Modify or delete existing rules 3. Click the Modify link next to the rule you want to modify Description of parameters when creating a new filtering rule On the Configuration Security Intrusion Detection you can enable/disable the intrusion detection function and also see and modify the existing rules 9.6.7.2 Intrusion Detection9.6.8 Virtual Server Create a new virtual server Create a DMZ zone External PacketInternal Host 9.6.9 IGMP Proxy 9.6.10 UPnP 10 Troubleshooting 10.1 Basic FunctionsLAN Connection Indication/Symptom10.2.1 How to use WINIPCFG 10.2.2 How to use IPCONFIG10.3 WAN Connection 10.4 WLAN ConnectionStart Run… type command and click OK . In the 10.5 Reset the HN294d 10.6 Safety Mode4. Click the Upgrade button 11.1 Product Care and Maintenance 11 Important Information11.2.3 Limited Warranty 11.2 License Agreement11.2.1 License 11.2.2 Term11.2.4 Intended Use 11.2.5 Limitation of Liability11.2.6 Governing Law 11.3.2 Safety Approvals 11.3 Regulatory Information11.3.1 EU Directives 11.3.1.1 Declaration of Conformity11.3.3 EMC Approvals 11.3.2.1 UL 1950 Statement11.3.4 Telecom Approval 11.3.3.1 FCC Part 15 Statement11.3.3.2 FCC RF Radiation Exposure Statement 11.3.4.1 FCC Part 68 Statement 11.3.5 Access Point Frequency Band 11.3.7 Power Supply11.3.6 Caution 11.3.8 Environmental InformationGlossary Access PointADSL AsynchronousDevice DHCPDomain name DOS attackDownstream DSLAMEncapsulation EthernetFirewall FirmwareG.lite HostHTTP IEEEIntranet IP addressMAC address Peer-to-peer PingPort POTSRouter SMTPSSID Stateful Inspection T1.413TCP/IP TelnetUPnP UpstreamVirtual Server VPI and VCI WLAN