IBM Partner Pavilion 6400 manual Configuring the printer, Shuttle Timeout

Page 24

configuring the printer

Table 3 Printer Configuration
PRINTER CONTROL	20 SECONDS
SHUTTLE TIMEOUT	20 SECONDS
PARALLEL INTERFACE	PC PARALLEL
INTERFACE TYPE	PC PARALLEL
PC PARALLEL	ENABLE
DATA BIT 8	ENABLE
DATA POLARITY	STANDARD
STROBE POLARITY	STANDARD
RESPONSE POLARITY	STANDARD
BUSY ON STROBE	ENABLE
LATCH DATA ON	TRAILING EDGE
PRIME SIGNAL	DISABLE
TOF ACTION AT PRIME SIGNAL .	NO ACTION

note

In Table 3 , only the values for Shuttle Timeout, Latch Data On, and Prime Signal need to be changed. For all other configuration items, the default values can be used. If the values shown in bold in Table

3are not set as shown, erratic operation of the printer might occur.

10	Multi–Platform Interface Feature Operation Guide

Image 24

Contents Coax/Twinax Multi-Platform Interface Feature Operation Guide Page Table of Contents Appendix B Describing Custom Set List of Tables in this Manual Electronics Emission Notices Federal Communications Commission FCC StatementCanadian Department of Communications Compliance Statement New Zealand Compliance StatementTrademarks and Service Marks SCSSafety Notices SikkerhedsinstrukionerTag stikket ud af kontakten inden De gør printeren ren Huomautuksia Turvallisuudesta Normas de SegurançaIrrota vaihtovirtajohto ennen kirjoittimen puhdistusta Säkerhetsföreskrifter SikkerhetsinformasjonKoppla los nätkabeln innan du rengör skrivaren Page About this setup guide Switching between Serial Ascii and Parallel AsciiRelated Publications Publication Title Document NumberConfiguration Preparing for Configuration Pre-Configuration ChecklistQuick Path Configuring MPI Configuring MPI Location of Configuration SwitchesSample Configuration Printout Twinax Sample Configuration Printout Coax Configuring MPI Configuring the Printer Configuring the printer Shuttle TimeoutConfiguring MPI for Either IGP or Code V Graphic Feature Configuring for port switching Using Coax with the MPI Coax Connection AttachmentLED Indicators Coax Buffer Size Display Screen Size, Print Buffer SizeCoax Code Dump Mode Entering Code Dump modeExiting Code Dump Mode Coax code dump modeCoax Command Interpreter Coax command interpreter Commands¬ONN¬FLS058¬OFF Coax Code Maps Translating Host Code Page to Ascii Code PagesInternal 3270 DSE/DSC to Ascii Character Map Coax code mapsMSB Ebcdic SCS to Ascii Character Map Following control codes are supported Coax code maps Using Twinax with the MPI Twinax Connection Twinax connectionActive jobs/devices Twinax connection Power off Smart T attachmentAddress switch Twinax connection Attach twinax cablesTwinax connection Power On Printer LED IndicatorsPrinter verification test Twinax Code Maps Twinax code mapsEbcdic SCS to Ascii Character MAP Following control codes are supported Code Dump Mode Twinax code dump modeExiting Code Dump Mode Code Dump Header An example of a Structured Field DumpTwinax Command Interpreter Commands Twinax command interpreterExample Using PC Parallel with MPI Introduction Connection PC parallel cable attachmentSetting time outs on the Parallel Host OS/2Troubleshooting Diagnostics Diagnostic HeaderDiagnostics Coax OperationCode Dump Mode if selected after test Twinax OperationChecklist Troubleshooting your Host Printer Operation Multi-Platform Interface Feature Operation Guide Compatibility Issues Cancel KeyCoax PA Keys Error Messages Compatibility issuesSwitching between Serial Ascii and Parallel Ascii Appendix a Defining a Printer in S/370-S/390 Environments Overview 6400-LU1-SCS-Local SNA 3174 Control Unit Vtam DefinitionJES2 Definition SYS1.PARMLIB 6400-LU1-SCS-Remote SNA 3174 Control Unit NCP DefinitionJES2 Definition 6400-LU3-DSE-Local SNA 3174 Control Unit Printer Settings 6400-LU3-DSE-Remote SNA 3174 Control Unit LOCADDR=#Printer ID 6400-LU0-DSC-Local Non-SNA 3174 Control Unit JES2 Definition SYS1.PARMLIB Appendix B Describing Custom Set Printer Configuration Printer configurationCustom Set 8 partial Proprinter III XL Emulation Print Language 335.3 MM Appendix C Illustrated Parts List Hardware assemblies Cable assemblies Cable assemblies Description Appendix D Installing the MPI on the Printer Introduction Accessing the card-cage Hardware installationPreparing the printer for MPI Installation Disconnect the data cable coming SlotInstalling the MPI Card in the Printer Next step is to install the MPI card as described belowAttaching the MPI Label Checking the MPI Installation Appendix E Host Character Sets Twinax Character Sets Multinational Ebcdic Character SetTwinax character sets USA Ebcdic Character Set Austria/Germany Ebcdic Character Set French Canadian Ebcdic Character Set Coax Character Sets Coax character setsUSA Ebcdic Character Set UK Internal 3270 Character Set UK Ebcdic Character Set Coax character sets Coax character sets