IBM Partner Pavilion 6400 manual Accessing the card-cage, Hardware installation

Page 95

hardware installation

Accessing the card-cage

danger

Disconnect the printer from any and all power before proceeding with any installation.

To access the Card–Cage:

1 Open the Printer Cover. Unload any paper.

2 Loosen the hold-down screws.

3 Lift slightly the right end and slide the Paper Guide Assembly to the left. Lift the paper guide assembly off the card cage. (See Figure 6 )

Figure 6	Paper guide
Put the paper guide assembly to the side	removal
Put the paper guide assembly to the side
for later re-installation.

Multi–Platform Interface Feature Operation Guide

81

Image 95

Contents Coax/Twinax Multi-Platform Interface Feature Operation Guide Page Table of Contents Appendix B Describing Custom Set List of Tables in this Manual Federal Communications Commission FCC Statement Electronics Emission NoticesNew Zealand Compliance Statement Canadian Department of Communications Compliance StatementSCS Trademarks and Service MarksTag stikket ud af kontakten inden De gør printeren ren Safety NoticesSikkerhedsinstrukioner Irrota vaihtovirtajohto ennen kirjoittimen puhdistusta Huomautuksia TurvallisuudestaNormas de Segurança Koppla los nätkabeln innan du rengör skrivaren SäkerhetsföreskrifterSikkerhetsinformasjon Page Switching between Serial Ascii and Parallel Ascii About this setup guidePublication Title Document Number Related PublicationsConfiguration Pre-Configuration Checklist Preparing for ConfigurationQuick Path Configuring MPI Location of Configuration Switches Configuring MPISample Configuration Printout Twinax Sample Configuration Printout Coax Configuring MPI Configuring the Printer Shuttle Timeout Configuring the printerConfiguring MPI for Either IGP or Code V Graphic Feature Configuring for port switching Using Coax with the MPI Attachment Coax ConnectionLED Indicators Display Screen Size, Print Buffer Size Coax Buffer SizeEntering Code Dump mode Coax Code Dump ModeCoax code dump mode Exiting Code Dump ModeCoax Command Interpreter Commands Coax command interpreter¬ONN¬FLS058¬OFF Translating Host Code Page to Ascii Code Pages Coax Code MapsCoax code maps Internal 3270 DSE/DSC to Ascii Character MapMSB Ebcdic SCS to Ascii Character Map Following control codes are supported Coax code maps Using Twinax with the MPI Active jobs/devices Twinax ConnectionTwinax connection Smart T attachment Twinax connection Power offTwinax connection Attach twinax cables Address switchLED Indicators Twinax connection Power On PrinterPrinter verification test Twinax code maps Twinax Code MapsEbcdic SCS to Ascii Character MAP Following control codes are supported Twinax code dump mode Code Dump ModeExiting Code Dump Mode An example of a Structured Field Dump Code Dump HeaderTwinax Command Interpreter Twinax command interpreter CommandsExample Using PC Parallel with MPI Introduction PC parallel cable attachment ConnectionOS/2 Setting time outs on the Parallel HostTroubleshooting Diagnostic Header DiagnosticsCoax Operation DiagnosticsTwinax Operation Code Dump Mode if selected after testChecklist Troubleshooting your Host Printer Operation Multi-Platform Interface Feature Operation Guide Coax PA Keys Compatibility IssuesCancel Key Compatibility issues Error MessagesSwitching between Serial Ascii and Parallel Ascii Appendix a Defining a Printer in S/370-S/390 Environments Overview Vtam Definition 6400-LU1-SCS-Local SNA 3174 Control UnitJES2 Definition SYS1.PARMLIB NCP Definition 6400-LU1-SCS-Remote SNA 3174 Control UnitJES2 Definition 6400-LU3-DSE-Local SNA 3174 Control Unit Printer Settings LOCADDR=# 6400-LU3-DSE-Remote SNA 3174 Control UnitPrinter ID 6400-LU0-DSC-Local Non-SNA 3174 Control Unit JES2 Definition SYS1.PARMLIB Appendix B Describing Custom Set Printer configuration Printer ConfigurationCustom Set 8 partial Proprinter III XL Emulation Print Language 335.3 MM Appendix C Illustrated Parts List Hardware assemblies Cable assemblies Cable assemblies Description Appendix D Installing the MPI on the Printer Introduction Hardware installation Accessing the card-cageDisconnect the data cable coming Slot Preparing the printer for MPI InstallationNext step is to install the MPI card as described below Installing the MPI Card in the PrinterAttaching the MPI Label Checking the MPI Installation Appendix E Host Character Sets Twinax character sets Twinax Character SetsMultinational Ebcdic Character Set USA Ebcdic Character Set Austria/Germany Ebcdic Character Set French Canadian Ebcdic Character Set Coax character sets Coax Character SetsUSA Ebcdic Character Set UK Internal 3270 Character Set UK Ebcdic Character Set Coax character sets Coax character sets