JVC GD-V501PCE manual Sound Adjustment, Mute, Bass, Treble, Balance

Page 22

Sound Adjustment

1 SOUND

Press to display the Sound menu.

INPUT

SURROUND

2 Select to adjust each item.

Press to select the desired adjustment menu.

Select the desired level by listening to the sound.

VOL

NR

PICTURE

SOUND

SET UP

PICTURE

POS /SIZE

Bass

Adjusts low sounds

Treble

Adjusts high sounds

Balance

Adjusts left and right volumes

Surround (see next page) Select On or Off

•To end adjustments

Sound
Normalise	Normal
Sound Mode	Normal
Bass	0
Treble	0
Balance	0
Surround	On

Normal

Auto

Emits the original sound.

Automatically controls proper volume level.

R

Press the R button

Note:

Press the SURROUND button to directly turn the surround effect On and Off. (see next page)

Bass, Treble and Surround settings are memorized separately for each Sound mode (Normal, Auto).

Helpful Hint ( N / Normalise Normalisation)

While the “Sound” menu is displayed, if either the N button on the remote control is pressed at any time or the (ACTION button) is pressed during “Normalise”, then all adjustment values are returned to the factory settings.

Mute

Useful when answering the phone or receiving unexpected visitors.

Press this button to mute the sound.

Press again to reactivate sound. Sound is also reactivated when power is turned off or volume level is changed.

22

Image 22

Contents Plasma Display Monitor GD-V501PCEINSTRUCTIONS Table of Contents Important Safety Notice Trademark CreditsImportant Safety Notice For UK only Important the Moulded PlugSetup Safety PrecautionsWhen using the Plasma Display Safety Precautions Cleaning and maintenanceIf problems occur during use Optional Accessories AccessoriesAccessories Supply Check that you have the accessories and items shownObserve the following precaution Remote Control BatteriesPrecaution on battery use Helpful HintConnections Cable fixing bandsSignal Names for D-sub 15P Connector Installing the ferrite core Small sizeInstalling the ferrite core Large size PC Input Terminals connectionSerial Terminals connection Installing the ferrite coreCommand Communication parametersBasic Controls OFF Timer button Input button AVS Video, Component/RGB and PC Mode SelectionSound mute On/Off see Volume Adjustment Basic ControlsConnecting the plug to the Wall Outlet Power On/Off and input signal selectionPower On/Off AC cord connectionPower On/Off and input signal selection Select the input signalSelecting the On-Screen Menu Language On-Screen Menu Display from Remote Control To Picture adjust menu Press to select each item SeeOn-Screen Menu Display from Remote Control See page 30 Component see To Signal screen for PC seeAspect Controls Just Aspect ControlsZoom AutoAdjusting Picture Pos./Size Adjusting screenHelpful Hint N / Normalise Normalisation Adjusting Picture Pos./SizeSize Clock Phase RGB/PC in Mode PosBass Sound AdjustmentMute TrebleOn Off Surround ControlsSurround Surround Button Dynamic Picture AdjustmentsNormal CinemaAdvanced Settings Picture AdjustmentsSet up Timer Present Time SetTimer Set Setup TimerReversal / Scroll selection Mode selectionScreensaver For preventing after-images To stop the Screensaver under On, press the buttonSide Panel Adjustment Setup of Screensaver TimeScreensaver For preventing after-images Component/RGB-in Select Setup for Input Signals3D Y/C Filter For Ntsc AV images Pulldown Setup for Input SignalsColour system / Aspect Auto If the picture image becomes unstableSetting PC sync signal Setup for input signals SyncSetting RGB sync signal Freq. kHz/V-Freq. HzTroubleshooting Plasma Display panel Symptoms CheckConnection to the Optional Video Input Card. IF-C50P1G AV input signalsComponent /RGB/PC input signals PC RGB inputAV Input Terminals connection Video signal connectionVideo 4 pin socket AV Out RGB signal R, G, B, HD, VD connection Component signals Y, PB, PR connectionComponent/RGB Input connection Specifications Mass Weight SpecificationsDimensions Optional SuppliedGD-V501PCE Plasma Display Monitor