JVC GD-V501PCE Setup for Input Signals, Component/RGB-in Select, 3D Y/C Filter For Ntsc AV images

Page 30

Setup for Input Signals

Component/RGB-in Select

Select the input signals to be connected by installing the Optional Video Input Card. (Refer to the service manual for the optional Video Input Card.)

Select to match the signals from the source connected to the Component/RGB input terminals.

Y, PB, PR signals “Component”

R, G, B, HD, VD signals “RGB”

		INPUT
	SURROUND
		VOL
N		R
PICTURE	SOUND	SET UP
PICTURE
POS. /SIZE		ASPECT

1

2

SET UP

Press to display the Setup menu screen.

Press to select the “Component/RGB-in Select”.

Press to select the desired mode.

Setup
Component/RGB-in select	RGB
	RGB
Signal
Screensaver	English (UK)
OSD Language	English (UK)
Set up TIMER
Component	RGB

R

Press to exit from adjust mode.

3D Y/C Filter – For NTSC AV images

Select “Signal” from the “Setup” menu during AV(S Video) input signal mode. (“Signal [AV]” menu is displayed.)

Press to select the “3D Y/C Filter (NTSC)”

Press to set On/Off.

R

Press to exit from adjust mode.

Setup
Component/RGB-in select	RGB
	RGB
Signal
Screensaver	English (UK)
OSD Language	English (UK)
Set up TIMER

Press (ACTION) button

Signal	[ AV ]
3D Y/C Filter (NTSC)	On
Colour system	Auto
3:2 Pulldown	Off
Aspect Auto (4:3)	4 : 3

Note:

When On, this setting only affects NTSC input signals.

30

Image 30

Contents Plasma Display Monitor GD-V501PCEINSTRUCTIONS Table of Contents Important Safety Notice Trademark CreditsImportant Safety Notice For UK only Important the Moulded PlugSafety Precautions SetupWhen using the Plasma Display Cleaning and maintenance Safety PrecautionsIf problems occur during use Optional Accessories AccessoriesAccessories Supply Check that you have the accessories and items shownObserve the following precaution Remote Control BatteriesPrecaution on battery use Helpful HintConnections Cable fixing bandsSignal Names for D-sub 15P Connector Installing the ferrite core Small sizeInstalling the ferrite core Large size PC Input Terminals connectionSerial Terminals connection Installing the ferrite coreCommand Communication parametersBasic Controls OFF Timer button Input button AVS Video, Component/RGB and PC Mode SelectionSound mute On/Off see Volume Adjustment Basic ControlsConnecting the plug to the Wall Outlet Power On/Off and input signal selectionPower On/Off AC cord connectionSelect the input signal Power On/Off and input signal selectionSelecting the On-Screen Menu Language On-Screen Menu Display from Remote Control To Picture adjust menu Press to select each item SeeOn-Screen Menu Display from Remote Control See page 30 Component see To Signal screen for PC seeAspect Controls Just Aspect ControlsZoom AutoAdjusting Picture Pos./Size Adjusting screenHelpful Hint N / Normalise Normalisation Adjusting Picture Pos./SizeSize Clock Phase RGB/PC in Mode PosBass Sound AdjustmentMute TrebleSurround Controls On OffSurround Surround Button Dynamic Picture AdjustmentsNormal CinemaAdvanced Settings Picture AdjustmentsSet up Timer Present Time SetTimer Set Setup TimerReversal / Scroll selection Mode selectionScreensaver For preventing after-images To stop the Screensaver under On, press the buttonSetup of Screensaver Time Side Panel AdjustmentScreensaver For preventing after-images Setup for Input Signals Component/RGB-in Select3D Y/C Filter For Ntsc AV images Pulldown Setup for Input SignalsColour system / Aspect Auto If the picture image becomes unstableSetting PC sync signal Setup for input signals SyncSetting RGB sync signal Freq. kHz/V-Freq. HzTroubleshooting Plasma Display panel Symptoms CheckConnection to the Optional Video Input Card. IF-C50P1G AV input signalsComponent /RGB/PC input signals PC RGB inputVideo signal connection AV Input Terminals connectionVideo 4 pin socket AV Out Component signals Y, PB, PR connection RGB signal R, G, B, HD, VD connectionComponent/RGB Input connection Specifications Mass Weight SpecificationsDimensions Optional SuppliedGD-V501PCE Plasma Display Monitor