JVC GD-V501PCE manual Important Safety Notice, For UK only Important the Moulded Plug

Page 4

Important Safety Notice

FOR UK ONLY

IMPORTANT: THE MOULDED PLUG

FOR YOUR SAFETY, PLEASE READ THE FOLLOWING TEXT CAREFULLY.

This appliance is supplied with a moulded three pin mains plug for your safety and convenience. A 5 amp fuse is fitted in this plug. Shall the fuse need to be replaced, please ensure that the replacement fuse has a rating of 5 amps and that it is approved by ASTA or BSI to BS1362.

Check for the ASTA mark ASA or the BSI mark on the body of the fuse.

If the plug contains a removable fuse cover, you must ensure that it is refitted when the fuse is replaced. If you lose the fuse cover the plug must not be used until a replacement cover is obtained.

A replacement fuse cover can be purchased from your local JVC Dealer.

If the fitted moulded plug is unsuitable for the socket outlet in your home, then the fuse shall be removed and the plug cut off and disposed of safety. There is a danger of severe electrical shock if the cut off plug is inserted into any 13 amp socket.

If a new plug is to be fitted, please observe the wiring code as shown below.

If in any doubt, please consult a qualified electrician.


WARNING:				THIS APPARATUS MUST BE EARTHED.

IMPORTANT:					The wires in this mains lead are coloured in accordance with the following code:

Green-and-Yellow:						Earth
Blue:						Neutral
Brown:						Live

As the colours of the wire in the mains lead of this appliance may not correspond with the coloured markings identifying the terminals in your plug, proceed as follows.

The wire which is coloured GREEN-AND-YELLOW must be connected to the terminal in the plug which is

marked with the letter E or by the Earth symbol or coloured GREEN or GREEN-AND-YELLOW.

The wire which is coloured BLUE must be connected to the terminal in the plug which is marked with the letter N or coloured BLACK.

The wire which is coloured BROWN must be connected to the terminal in the plug which is marked with the letter L or coloured RED.

How to replace the fuse. Open the fuse compartment with a screwdriver and replace the fuse.

4

Image 4

Contents Plasma Display Monitor GD-V501PCEINSTRUCTIONS Table of Contents Important Safety Notice Trademark CreditsImportant Safety Notice For UK only Important the Moulded PlugSetup Safety PrecautionsWhen using the Plasma Display Safety Precautions Cleaning and maintenanceIf problems occur during use Accessories Accessories SupplyOptional Accessories Check that you have the accessories and items shownRemote Control Batteries Precaution on battery useObserve the following precaution Helpful HintConnections Cable fixing bandsInstalling the ferrite core Small size Installing the ferrite core Large sizeSignal Names for D-sub 15P Connector PC Input Terminals connectionInstalling the ferrite core CommandSerial Terminals connection Communication parametersBasic Controls Input button AVS Video, Component/RGB and PC Mode Selection Sound mute On/Off see Volume AdjustmentOFF Timer button Basic ControlsPower On/Off and input signal selection Power On/OffConnecting the plug to the Wall Outlet AC cord connectionPower On/Off and input signal selection Select the input signalSelecting the On-Screen Menu Language On-Screen Menu Display from Remote Control To Picture adjust menu Press to select each item SeeOn-Screen Menu Display from Remote Control See page 30 Component see To Signal screen for PC seeAspect Controls Aspect Controls ZoomJust AutoAdjusting Picture Pos./Size Adjusting screenAdjusting Picture Pos./Size Size Clock Phase RGB/PC in ModeHelpful Hint N / Normalise Normalisation PosSound Adjustment MuteBass TrebleOn Off Surround ControlsSurround Surround Button Picture Adjustments NormalDynamic CinemaAdvanced Settings Picture AdjustmentsSet up Timer Present Time SetTimer Set Setup TimerMode selection Screensaver For preventing after-imagesReversal / Scroll selection To stop the Screensaver under On, press the buttonSide Panel Adjustment Setup of Screensaver TimeScreensaver For preventing after-images Component/RGB-in Select Setup for Input Signals3D Y/C Filter For Ntsc AV images Setup for Input Signals Colour system / Aspect AutoPulldown If the picture image becomes unstableSetup for input signals Sync Setting RGB sync signalSetting PC sync signal Freq. kHz/V-Freq. HzTroubleshooting Plasma Display panel Symptoms CheckAV input signals Component /RGB/PC input signalsConnection to the Optional Video Input Card. IF-C50P1G PC RGB inputAV Input Terminals connection Video signal connectionVideo 4 pin socket AV Out RGB signal R, G, B, HD, VD connection Component signals Y, PB, PR connectionComponent/RGB Input connection Specifications Specifications DimensionsMass Weight Optional SuppliedGD-V501PCE Plasma Display Monitor