Onkyo PR-SC5508 Connecting Onkyo uComponents, How to record the video, Auto Power On

Page 21

Note

*1

Connect a turntable (MM) that has built-in a phono preamp to TV/CD IN or connect it to PHONO IN with the phono preamp turned

 

off. If your turntable (MM) doesn’t have a phono preamp, connect to PHONO IN. If your turntable has a moving coil (MC) type car-

 

tridge, you’ll need a commercially available MC head amp or MC transformer to connect to PHONO IN. See your turntable’s man-

 

ual for details.

 

If your turntable has a ground wire, connect it to the AV controller’s GND screw. With some turntables, connecting the ground wire

 

may produce an audible hum. If this happens, disconnect it.

*2

When you connect your personal computer to PC IN and select PC input selector, video of the personal computer is output from

 

HDMI output. However, because the AV controller selects the video input in the order of HDMI > component > analog RGB, if you

 

have assigned HDMI IN to the PC input selector, the AV controller will output signals from HDMI IN in priority to PC IN.

*3

Before using the multichannel input, you must assign it to an input selector. See “Analog Audio Input” (47). To select the multi-

 

channel input, see “Audio Selector” (64). To adjust the subwoofer sensitivity for the multichannel input, see “Subwoofer Input

 

Sensitivity” (47).

The AV controller can output audio and video signals from the AUX INPUT jacks to the VCR/DVR OUT jacks.

With connection D, you can listen and record audio from the external components while you are in Zone 2/3. You can listen and record audio from the external components in the main room; you can listen to the audio in Zone 2/3 as well.

With connection C, you can enjoy Dolby Digital and DTS. (To record or listen in Zone 2/3 as well, use C and D.)

How to record the video

With the connections described above, you cannot record the video through the AV controller. To make a connection for video recording (35).

Connecting Onkyo uComponents

Step 1:

Make sure that each Onkyo component is connected with an analog audio cable (connection D in the hookup examples) (20).

Step 2:

Make the uconnection (see illustration below).

Step 3:

If you’re using an RI Dock, or cassette tape deck, change the Input Display (28).

With u(Remote Interactive), you can use the following special functions:

Auto Power On

When you start playback on a component connected via uwhile the AV controller is on Standby, the AV con- troller will automatically turn on and select that compo- nent as the input source.

Direct Change

When playback is started on a component connected via u, the AV controller automatically selects that compo- nent as the input source.

Remote Control

You can use the AV controller’s remote controller to control your other u-capable Onkyo components, pointing the remote controller at the AV controller’s remote control sensor instead of the component. You must enter the appropriate remote control code first (88).

Note

Use only ucables for uconnections. ucables are supplied with Onkyo players (DVD, CD, etc.).

Some components have two ujacks. You can connect either one to the AV controller. The other jack is for connecting addi- tional u-capable components.

Connect only Onkyo components to ujacks. Connecting other manufacturer’s components may cause a malfunction.

Some components may not support all ufunctions. Refer to the manuals supplied with your other Onkyo components.

While Zone 2 or Zone 3 is on, the Auto Power On and Direct Change ufunctions do not work.

Do not use uconnections if you use HDMI Control (RIHD) (61).

IN

L

R

TV/CD

REMOTE CONTROL

IN

L

R

BD/DVD

 

R

L

e.g., CD player

ANALOG

AUDIO OUT

 

R

L

e.g., DVD player

ANALOG

AUDIO OUT

En

21

Image 21
Contents Advanced Operations Controlling iPod & Other Components Introduction Connections10 cm 4 at the rear. The rear edge of the shelf or Always consider the environmental issues and followBoard above the apparatus shall be set 10 cm Away from the rear panel or wall, creating a flue-likePrecautions Using the Remote Controller Supplied AccessoriesInstalling the Batteries Aiming the Remote ControllerContents Processing FeaturesMiscellaneous Analog RGB Video Input D-sub 15 for PCTHX Ultra2 Plus V.Color is a trademark of Sony CorporationMusic Optimizer is a trademark of Onkyo Corporation Front & Rear Panels Pure Audio button Hdmi Thru indicatorFront Panel ON/STANDBY buttonDisplay Return button Setup MIC jackPhones jack Zone 2, Zone 3 and OFF buttons AUX Input jacks HDMI, VIDEO, Audio L/R and Digital 19Rear Panel Input jacks Balance L/R 12V Trigger OUT A/B/C jacksFront L/R, CENTER, Surr L/R Controlling the AV Controller Remote ControllerEnjoying Home Theater About Home TheaterConnecting Your Speakers Connecting the AV ControllerSpeaker Configuration Connecting a Power Amplifier with RCA InputsAV controller Multichannel Connecting a Power Amplifier with XLR InputsUsing Dipole Speakers Connecting the Powered SubwoofersBalanced XLR cable Speaker Impedance Bi-amping the Front SpeakersStereo audio source with Balanced XLR output Connecting a Balanced Audio SourceConnected image with AV components About AV ConnectionsAV Cables and Jacks Hdmi cableJack Signal Components Connecting Your Components with HdmiAssignment can be changed 45 to Audio return channel ARC functionConnecting Your Components Jack Signal Components AssignableFront Rear How to record the video Connecting Onkyo uComponentsAuto Power On Remote ControlConnecting the Power Cord Connecting AntennaNorth American European and Asian Models AC InletMonitor Out setting set to Both, BothMain or BothSub Monitor Out setting set to Hdmi Main or Hdmi SubWhich Connections Should I Use? Video Connection FormatsFor details, refer to Video Resolution Chart Monitor Out setting set to AnalogDepends on the Audio TV Out setting Audio Connection FormatsTurning On/Off the AV Controller Standby indicatorTurning On Turning OffSetting the Display Brightness Displaying Source InformationTOR Using the Sleep Timer Using the Home MenuMuting the AV Controller Using Activities to Start Easy Macros Using HeadphonesStarting Components Using Activities Changing the Input DisplayRestoring Default Audyssey MultEQ XT32 Room Correction and Speaker SetupUsing Audyssey MultEQ XT32 Turning Off the ComponentsEnter Error Messages Changing the Speaker Settings ManuallyUsing a Powered Subwoofer Tuning into Radio Stations Using the TunerListening to the Radio Listening to the RadioUsing RDS excluding North American models Presetting FM/AM StationsFinding Stations by Type PTY Listening to Traffic News TPRDS program types PTY Recording Connecting a Recording ComponentRecording Separate AV Sources AV RecordingUsing the Listening Modes Listening Mode ButtonsSelecting Listening Modes Explanatory Notes About Listening ModesInput Source Speaker LayoutListening Modes Description Input Speaker Source Layout DTS-HD High Resolution AudioDTS-HD Master AudioListening Mode Description Input Speaker Source Layout Neural Digital Modes can be usedMusic *5 Sources such as MP3s and Internet streamsOnkyo-Original DSP Listening Modes On-screen Setup Menus Advanced SetupCommon Procedures in Setup Menu MenuInput/Output Assign Monitor OutOUT Main Resolution Hdmi InputBD/DVD, VCR/DVR, CBL/SAT, GAME, PC, Tape TV/CD, PHONO, Port ` in 1, in 2, Component Video InputAnalog Audio Input Digital Audio InputSpeaker Settings Speaker SetupLevel Calibration Speaker DistanceEqualizer Settings THX Audio SetupBGC Audio Adjust Multiplex/MonoDolby Volume Leveler Dolby VolumeHalf Mode PLIIz Height GainSource Setup Reference Level Dynamic VolumeIntelliVolume SyncName Edit Picture Adjust Mosquito NR*2*3*4*6 Resolution*2*4Random NR*2*3*4*6 Block NR*2*3*4*6DTS/DTS-ES/DTS-HD Listening Mode PresetOSD Setup Volume Setup12V Trigger A/B/C Setup MiscellaneousSirius Settings North American models Hardware SetupRemote ID Multi ZoneHdmi ControlRIHD Power ControlAudio Return Channel TV ControlUsing the Audio Settings Lock SetupDolby Volume Audyssey SettingsSpeaker Levels Music OptimizerSetting the Incoming Digital Signal Fixed Mode Re-EQAudio Selector Connecting the AV Controller About NETNetwork Requirements Listening to Internet Radio Listening to vTuner Internet RadioListening to Other Internet Radio Station and Song Presets Registering Presets*1Playing Music Files on a Server Items on the Internet Radio Top MenuWindows Media Player 11 Setup WMA Supported Audio File FormatsWAV AACRemote Playback from Media Server/ Personal Computer Windows Media Player 12 SetupServer Requirements About DlnaUsing Remote Playback Network SettingsDhcp About USB List of the device’s contents appearsUSB Mass Storage Device Requirements Playing Music Files on a USB DeviceFolder1 02SongTrack2 Artist Album 011234 Connecting Your Zone 2 Speakers Connecting ZoneMulti Zone Zone 2 Video OutputConnecting Your Zone 3 Speakers Setting the Multi ZoneZone 2 Maximum Volume, Zone 3 Maximum Volume Zone 2 Out, Zone 3 OutZone 2 Power On Volume, Zone 3 Power On Volume Using Zone 2/3Controlling Zone 2/3 from the AV controller Zone 2 Component OutAdjusting the Volume for Zones Controlling Zone 2/3 with the Remote ControllerAdjusting the Tone and Balance of Zones Muting ZonesTrigger OUT B and C Using the 12V TriggersUsing a Multiroom Kit with Zone 2/3 Using a Multiroom Kit with a CabinetUsing a Multiroom Kit with Other Components Extended Mode control Standard Mode controlPlaying Music Files on the iPod/iPhone Top screen listConnecting an Onkyo Dock Models sold are different depending on the regionOnkyo Dock Cable UP-A1 Dock Using the Onkyo DockRI Dock Controlling Your iPodWithout the RI Control With the RI ControlOnkyo Dock Buttons UP-A1 Dock Available buttonsUDock E/rENTER PLAYLISTe/rPreprogrammed Remote Control Codes Looking up for Remote Control CodeControlling Other Components Via network, and then press Enter Use q/wto select Search by model numberOr if you are not sure about the exact model Select Skip, and then press EnterRemote Control Codes for Onkyo Components Connected via u Entering Remote Control CodesRemote Mode BD/DVD TapeResetting the Remote Controller Resetting Remote Mode ButtonsYou can reset the remote controller to its default settings Controlling Other ComponentsCassettetape deck Components ButtonsTV VOL q/w CH + Disc +Activities Setup To learn more commands, repeat steps 2 Learning CommandsFollowing buttons cannot learn new commands Remote MODE, ALL OFF, MY MOVIE, MY TV, MY Music and ModeDeleting Learning Commands Using Normal MacrosMaking Macros Running MacrosStandby indicator flashes red TroubleshootingCan’t turn on the AV controller There’s no sound, or it’s very quietCan’t select the Pure Audio listening mode There’s no sound with a certain signal formatAbout DTS signals Only the center speaker produces soundThere’s no picture Remote controller doesn’t workThere’s no picture from a source connected to an Hdmi On-screen menus don’t appearCan’t access the server or Internet radio Can’t learn commands from another remote controllerCan’t access the music files on a USB device Stand-by power consumptionSpeaker distance cannot be set as required Sound changes when I connect my headphonesDisplay doesn’t work How do I change the language of a multiplex sourceNent Video Monitor OUT Important Note Regarding Video PlaybackAmplifier Section SpecificationsVideo Section Tuner SectionAbout Hdmi Supported Audio FormatsAbout Copyright Protection Using an RIHD-compatible TV, Player, or Recorder About p-compatible componentsOperations that can be performed with p connection Confirm the connecting and setting How to connect and setupConfirm the settings Operate with the remote controllerUpdate procedure Firmware UpdateUpdating the Firmware via Network Before you startTroubleshooting Errors during update via networkUpdating the Firmware via USB Errors during update via USB Output Video Resolution ChartOnkyo Europe Electronics GmbH UK Branch Onkyo Europe Electronics GmbH