JVC DT-V17G1 Dear Customer, Information for Users on Disposal of Old Equipment, EMC Supplement

Page 3
Attention: This symbol is only valid in the European Union.

U.S.A. only

European Union only

FCC NOTICE

CAUTION: Changes or modifications not approved by JVC could void the user’s authority to operate the equipment.

NOTE: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.

IMPORTANT RECYCLING INFORMATION

This product has a fluorescent lamp that contains mercury. Disposal of these materials may be regulated in your community due to environmental considerations. For disposal or recycling information, please contact your local authorities or for USA, the Electronic Industries Alliance: http://www.eiae.org

WARNING: TO PREVENT FIRE OR SHOCK HAZARDS, DO NOT EXPOSE THIS APPARATUS TO RAIN OR MOISTURE.

WARNING: THIS APPARATUS MUST BE CONNECTED TO A MAINS SOCKET OUTLET WITH A PROTECTIVE EARTHING CONNECTION.

CAUTION: DANGER OF EXPLOSION IF BATTERY IS INCORRECTLY REPLACED.

REPLACE ONLY WITH THE SAME OR EQUIVALENT TYPE.

IMPORTANT SAFETY INSTRUCTIONS

1)

Read these instructions.

2)

Keep these instructions.

3)

Heed all warnings.

4)

Follow all instructions.

5)

Do not use this apparatus near water.

6)

Clean only with dry cloth.

7)

Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.

8)

Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including

 

amplifiers) that produce heat.

9)

Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades

 

with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide

 

blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult

 

an electrician for replacement of the obsolete outlet.

10)

Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and

 

the point where they exit from the apparatus.

11)

Only use attachments/accessories specified by the manufacturer.

12)

Use only with the cart, stand, tripod, bracket, or table specified by the

 

manufacturer, or sold with the apparatus. When a cart is used, use caution when

 

moving the cart/apparatus combination to avoid injury from tip-over.

13)

Unplug this apparatus during lightning storms or when unused for long periods of

 

time.

14)

Refer all servicing to qualified service personnel. Servicing is required when the

 

apparatus has been damaged in any way, such as power-supply cord or plug is

 

damaged, liquid has been spilled or objects have fallen into the apparatus, the

 

apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

15)

Apparatus shall not be exposed to dripping or splashing and no objects filled with liquids, such as vases, shall

 

be placed on the apparatus.

16)

Batteries shall not be exposed to excessive heat such as sunshine, fire or the like.

17)

When discarding batteries, environmental problems must be considered and the local rules or laws governing

 

the disposal of these batteries must be followed strictly.

Dear Customer,

This apparatus is in conformance with the valid European directives and standards regarding electromagnetic compatibility and electrical safety.

European representative of Victor Company of Japan, Limited is:

JVC Technical Services Europe GmbH Postfach 10 05 04

61145 Friedberg Germany

Information for Users on Disposal of Old Equipment

[European Union]

This symbol indicates that the electrical and electronic equipment should not be disposed as general household waste at its end-of- life. Instead, the product should be handed over to the applicable collection point for the recycling of electrical and electronic equipment for proper treatment, recovery and recycling in accordance with your national legislation.

By disposing of this product correctly, you will help to conserve natural resources and will help prevent potential negative effects on the environment and human health which could otherwise

be caused by inappropriate waste handling of this product. For more information about collection point and recycling of this product, please contact your local municipal office, your household waste disposal service or the shop where you purchased the product.

Penalties may be applicable for incorrect disposal of this waste, in accordance with national legislation.

(Business users)

If you wish to dispose of this product, please visit our web page http://www.jvc.eu/ to obtain information about the take-back of the product.

[Other Countries outside the European Union]

If you wish to dispose of this product, please do so in accordance with applicable national legislation or other rules in your country for the treatment of old electrical and electronic equipment.

EMC Supplement

This equipment is in conformity with the provisions and protection requirements of the corresponding European Directives. This equipment is designed for professional video appliances and can be used in the following environments:

•Controlled EMC environment (for example purpose built broadcasting or recording studio), and rural outdoors environment (far away from railways, transmitters, overhead power lines, etc.)

In order to keep the best performance and ensure electromagnetic compatibility, we recommend to use cables not exceeding the following length:

Cable

Length

Power cord

2.0 m

(attached cable (H05VV-F 3 x 0.75 mm2))

 

Video signal cable (coaxial cable)

2.0 m

Audio signal cable (shielded cable)

1.5 m

DVI cable (shielded cable)

2.0 m

RS-232C cable (shielded cable)

2.0 m

(A straight cable with a D-sub 9-pin connector)

RS-485 cable (twist pair cable)

2.0 m

(A straight LAN cable)

 

REMOTE cable (twist pair cable)

2.0 m

(A straight LAN cable)

 

The inrush current of this apparatus is 14.80 ampere.

CAUTION

In case where the strong electromagnetic waves or magnetism are near the audio cable or the signal cable, the sound or the picture will contain noise. In such cases, please keep the cable away from the sources of the disturbance.

ENGLISH3

Page 2 Page 4
Image 3
Page 2 Page 4
Contents DT-V17G1 These openings must not be blocked or covered Safety PrecautionsPower Connection How to replace the fuseFCC Notice Dear CustomerInformation for Users on Disposal of Old Equipment EMC SupplementScrew holes for stand attachment Stand body Monitor InstallationTo install the stand To detach the standFixing the monitor To adjust the stand heightTo prevent an accidental fall Lower positionDaily Operations / Connections Front panelDual Link SDI Press Menu button Press or button when a menu is not displayedDisplay the menu Press buttons to select an item, then press buttonRear panel Attaching the power cord holder When no video signal comes Video signalsOn the signal format When a DVI-D signal protected with Hdcp is inputGND Status indication of Dual LINK/3G SDI signal informationStatus indication of 3G SDI signal information Status indication of Dual LinkPicture Function Menu Configuration-MAIN MenuMARKER*1*2 Setting of Area MARKER, Safety MARKER, R-AREA MarkerAudio Setting Settings of E.AUDIO GroupSync Function Scope SETTING*1Example of the vector scope Example of the wave form monitorSettings of sub menu Posi Function SettingPicture SUB ADJ White Balance SET SIZE/POSI. ADJInformation Setting of Character SETENGLISH19 All resetUsing the MAKE/TRIGGER system External ControlAbout the external control Component Tally SELSDI DVIUsing the serial communication Basic command list Functions DataENGLISH23 Troubleshooting Self-check program MaintenanceInput/output terminals SpecificationsGeneral LCD panelENGLISH27 Front viewSide view Rear view

DT-V17G1 specifications

The JVC DT-V17G1 is a high-performance 17-inch LCD monitor specifically designed for broadcast and production environments. With its advanced features and cutting-edge technologies, it offers an exceptional viewing experience, making it an excellent choice for professionals in the filmmaking and broadcasting industry.

One of the standout features of the DT-V17G1 is its Full HD resolution of 1920 x 1080 pixels, ensuring that images are rendered with stunning clarity and detail. This level of resolution makes it ideal for critical monitoring tasks, allowing professionals to see every nuance in their footage. The monitor also boasts a high brightness level of 300 cd/m², which combined with a contrast ratio of 1000:1, provides excellent visibility even in brightly lit environments.

The DT-V17G1 employs advanced color processing technologies, including 10-bit color depth, which results in a wider color gamut and smoother gradations. This is particularly important for color-critical applications where accurate color representation is essential. The monitor supports various color spaces, including BT.709, making it versatile for different production standards.

In terms of connectivity, the JVC DT-V17G1 is equipped with multiple input options, including HDMI, SDI, and Composite inputs. This versatility ensures it can easily integrate into a wide range of production setups, whether for live broadcasts, video editing, or post-production environments. The monitor also features loop-through capabilities for SDI, allowing for easy signal distribution to other devices.

Another remarkable characteristic of the DT-V17G1 is its comprehensive set of built-in tools designed to assist in video production. These include waveform and vector scope displays, which provide valuable information about the signal's quality and help maintain broadcast standards. Furthermore, the monitor comes with peaking, false color, and zebra patterns, which enhance focus and exposure control.

The JVC DT-V17G1 is housed in a robust and lightweight chassis, making it suitable for both studio and field use. Its ergonomic design includes VESA mount compatibility, offering flexible mounting options to suit different production environments. This combination of advanced features, professional-grade technology, and user-friendly design makes the JVC DT-V17G1 a reliable and indispensable tool for any broadcast or production professional. With its high-quality display and range of monitoring capabilities, it is poised to meet the demands of today’s media industry.
Top Page Image Contents