JVC MP-XP7210GB, MP-XP3210GB warranty 62 EN, Power-saving mode

Page 62

62 EN

HARDWARE

Power-saving mode

In compliance with the operation regulations of the International Energy Star Program, this unit enters the power-saving mode when no operation is performed for a certain period.

On the [Power Schemes] tab in the “Power Option Properties” screen (page 61), you can specify the time that must expire before the unit enters the power-saving mode. The table below shows the factory settings.

		Operating on	Operating				Status
		AC power	on battery				Status
		AC power	on battery
1	Turn off monitor:	15 minutes	5 minutes	The LCD screen turns off.
				The			(Stand By) lamp is still lit in green.



				The hard disk power is turned off with
2	Turn off hard disks:	30 minutes	5 minutes	the LCD screen kept off. The


				(Stand By) lamp is still lit in green.

3	System standby:	20 minutes	5 minutes	The LCD screen is turned off.
3	System standby:	20 minutes	5 minutes	The			(Stand By) lamp flashes in green.



4	System hibernates:	3 hours	2 hours	The PC stores the current system status
				on the hard disk. The					(Stand By) lamp


				will go out.

Tips

To exit status 1 or 2 , move the stick or press any key on the keyboard. To exit status 3 , press the Power key or any key on the keyboard.

To exit status 4 , press the Power key.

Important

•In statuses 1 through 3, Windows is still running. Note that the current condition is lost if the PC is turned off by pressing the Power key for more than 4 seconds.

Image 62

Contents MP-XP7210GB/MP-XP3210GB Dear Customer It is recommended that youSome DO’S and DON’TS on the Safe USE of Equipment Important Safety Instructions EN5 About BatteriesChecking Inventory Restriction JVC Software License AgreementCopyright Ownership Grant of License Transfer of the SoftwareTerm Limited WarrantyLimitation of Liability TerminationEND-USER License Agreement Copyright Ownership10 EN Restricted Rights LegendTable of contents 12 EN Parts and Component NamesSetting UP ¡ Mounting Battery Pack ¡ Dismounting Battery Pack Unplug the jumper pin before recharging the battery packMounting/Dismounting the Lithium Ion Battery Pack 14 ENOpen the display panel 16 EN Make sure that the battery pack is fully charged¡ Make sure that the battery pack is fully recharged Standard recharging timePress the On/Off key ¡ Status indicatorsTurning On/Off Key On Rename your computer and click Next Initial Setup of Microsoft Windows18 EN Click NextEnter the user name and click Next Click FinishClick start 20 ENTurn-Off Click Turn Off computerJVC Original Software and System Applications Setup software Setup of JVC Original SoftwareRead the License Agreement when displayed 22 ENDVC’s USB Drivers If The hardware JVC DV Camera Storage message appears24 EN If The hardware JVC Web Camera message appearsCC Converter ¡ Enable¡ Disable Explanation of menu options26 EN ¡ Real Player 8 Basic ¡ Acrobat Reader ¡ Norton AntiVirus¡ Pixela ImageMixer 28 EN To Set Up the Standard Applications AgainTo Uninstall a Standard Application Navigate in the Internet World 30 EN Contracting with the Internet Service Provider¡When you have contracted with a provider ¡ Contract with the providerConnection of Telephone Line and Modem Setup 32 EN Seting up the modemInternet Connection Setup 34 EN Click Set up my connection manually option, and click NextClick Connect using a dial-up modem option, and click Next Click Connect to the Internet option, and click NextClick Finish. The setup for connection wizard is complete Enter the phone number, and click Next36 EN Internet Protocol TCP/IP Properties screen will appear Click Connect Connecting to the Internet38 EN Disconnection from the Internet Accessing a Web 40 ENSetting up E-Mail Software Click start and click E-mail on the Menu42 EN Enter the Account name and Password, and click Next Transmission 44 ENSending and Receiving E-mails CreateCreate a message 46 EN To check the received messages, click Inbox on the screenHardware Using the Pointing Device 48 ENScroll buttons Double-clickDrag 50 EN Using Hot keysUsing the Numeric Keypad Increasing the Optional Memory Capacity 52 EN Adding or Removing a Memory BoardMounting a memory board Removing the memory boardTotal amount of memory appears on the screen 54 ENChecking the Additional Memory Board Insert an SD memory card Using the SD Memory Card SlotRemove the dummy card 56 EN Using an External Display UnitConnecting an external monitor ¡Setting the IP address manually Connecting to a networkSetting for network connection ¡Setting a computer name or work group 58 EN¡Checking the MAC address 60 EN Checking the battery level Click the Power Meter tabPower-saving mode 62 ENSystem in standby status System in halt status64 EN Unknown partition on hard diskPC Recovery Repeated PC Setup 66 EN Setting Up Your PC AgainBefore starting Repeated PC Setup If you respond with a System Recovery ProcedureSelect the recovery method disk partitioning If you respond with CComputer Wiederherstellung Recovery 68 ENTroubleshooting 70 EN PowerPower does not turn on If the Q&A does not help youTerminating an application forcibly Startup and Operation of WindowsScreen has hung Troubleshooting 72 ENDisplay ¡ When the Stand By lamp is flashing¡ When the Stand By lamp is not lit PC is turned on but nothing appears on the screen74 EN Using the Internet¡ When a divider is used Cannot dial upPC dials but connection is not established PC cannot send or receive e-mail messages Check the following ¡ Check the user name and password76 EN ¡ The internal modem dials but negotiation is not madeBattery discharge faster than expected BatteryBattery is not charged Miscellaneous Forgot the password78 EN PC is hotSetting procedure does not complete 80 EN Appendix 82 EN List of Support CentresTrademark notice Specification 84 ENOptions separately available MP-VGX1E86 EN Page 88 EN Page Victor Company of JAPAN, Limited