JVC MP-XP3210GB, MP-XP7210GB warranty Setting procedure does not complete

Page 79

EN 79

¡If you forget the BIOS password

The following passwords can be set on the BIOS.

User password

When this password is set, the user is requested to enter the password to start Windows or change a BIOS setting.

HDD password

The password required for accessing the hard disk.

Important

You cannot delete the BIOS password even if you forget it. To delete it forcibly, you have to return your PC to us for chargeable service. (It may require hard disk drive replacement.)

To bring up the BIOS menu, turn on the PC and press the [Alt] and [F2] keys while the Victor logo screen is shown.

Do not change the BIOS setting unless you have adequate knowledge of computers. A wrong setting can make your PC unable to start up again or, worse, damage it.

Q.

A.

Setting procedure does not complete.

If Internet, e-mail, or any other setting does not complete through the procedure described in this manual, check the following.

If the [Control Panel] display is in Classical mode, change it to the Category mode. All the setting procedures in this manual assume the Category display mode.

Image 79
Contents MP-XP7210GB/MP-XP3210GB It is recommended that you Dear CustomerSome DO’S and DON’TS on the Safe USE of Equipment Important Safety Instructions About Batteries EN5Checking Inventory Transfer of the Software JVC Software License AgreementCopyright Ownership Grant of License RestrictionTermination Limited WarrantyLimitation of Liability TermCopyright Ownership END-USER License AgreementRestricted Rights Legend 10 ENTable of contents Parts and Component Names 12 ENSetting UP 14 EN Unplug the jumper pin before recharging the battery packMounting/Dismounting the Lithium Ion Battery Pack ¡ Mounting Battery Pack ¡ Dismounting Battery PackOpen the display panel Standard recharging time Make sure that the battery pack is fully charged¡ Make sure that the battery pack is fully recharged 16 ENTurning On/Off Key On ¡ Status indicatorsPress the On/Off key Click Next Initial Setup of Microsoft Windows18 EN Rename your computer and click NextClick Finish Enter the user name and click NextClick Turn Off computer 20 ENTurn-Off Click startJVC Original Software and System Applications 22 EN Setup of JVC Original SoftwareRead the License Agreement when displayed Setup softwareIf The hardware JVC DV Camera Storage message appears DVC’s USB DriversIf The hardware JVC Web Camera message appears 24 ENExplanation of menu options ¡ Enable¡ Disable CC Converter26 EN ¡ Pixela ImageMixer ¡ Acrobat Reader ¡ Norton AntiVirus¡ Real Player 8 Basic To Uninstall a Standard Application To Set Up the Standard Applications Again28 EN Navigate in the Internet World ¡ Contract with the provider Contracting with the Internet Service Provider¡When you have contracted with a provider 30 ENConnection of Telephone Line and Modem Setup Seting up the modem 32 ENInternet Connection Setup Click Connect to the Internet option, and click Next Click Set up my connection manually option, and click NextClick Connect using a dial-up modem option, and click Next 34 ENEnter the phone number, and click Next Click Finish. The setup for connection wizard is complete36 EN Internet Protocol TCP/IP Properties screen will appear 38 EN Connecting to the InternetClick Connect Disconnection from the Internet 40 EN Accessing a WebClick start and click E-mail on the Menu Setting up E-Mail Software42 EN Enter the Account name and Password, and click Next Create 44 ENSending and Receiving E-mails TransmissionCreate a message To check the received messages, click Inbox on the screen 46 ENHardware 48 EN Using the Pointing DeviceDrag Double-clickScroll buttons Using the Numeric Keypad Using Hot keys50 EN Increasing the Optional Memory Capacity Adding or Removing a Memory Board 52 ENRemoving the memory board Mounting a memory boardChecking the Additional Memory Board 54 ENTotal amount of memory appears on the screen Remove the dummy card Using the SD Memory Card SlotInsert an SD memory card Connecting an external monitor Using an External Display Unit56 EN Setting for network connection Connecting to a network¡Setting the IP address manually 58 EN ¡Setting a computer name or work group¡Checking the MAC address 60 EN Click the Power Meter tab Checking the battery level62 EN Power-saving modeSystem in halt status System in standby statusUnknown partition on hard disk 64 ENPC Recovery Repeated PC Setup Before starting Repeated PC Setup Setting Up Your PC Again66 EN If you respond with C System Recovery ProcedureSelect the recovery method disk partitioning If you respond with a68 EN Computer Wiederherstellung RecoveryTroubleshooting If the Q&A does not help you PowerPower does not turn on 70 ENScreen has hung Startup and Operation of WindowsTerminating an application forcibly 72 EN TroubleshootingPC is turned on but nothing appears on the screen ¡ When the Stand By lamp is flashing¡ When the Stand By lamp is not lit DisplayCannot dial up Using the Internet¡ When a divider is used 74 ENPC dials but connection is not established ¡ The internal modem dials but negotiation is not made Check the following ¡ Check the user name and password76 EN PC cannot send or receive e-mail messagesBattery is not charged BatteryBattery discharge faster than expected PC is hot Forgot the password78 EN MiscellaneousSetting procedure does not complete 80 EN Appendix List of Support Centres 82 ENTrademark notice 84 EN SpecificationMP-VGX1E Options separately available86 EN Page 88 EN Page Victor Company of JAPAN, Limited