Onkyo HT-RC270 Speaker Setup, Speaker Settings, Speaker Configuration, Speaker Impedance, Front

Speaker Setup Speaker Configuration

Main menu Speaker Setup

Some of the settings in this section are set automatically by Audyssey MultEQ® Room Correction and Speaker Setup function (➔ 29).

Here you can check the settings made by

Audyssey MultEQ Room Correction and Speaker Setup function, or set them manually, which is useful if you change one of the connected speakers after using Audyssey MultEQ Room Correction and Speaker Setup function.

Note

•These settings are disabled when:

–a pair of headphones is connected, or

–the “Audio TV Out” setting is set to “On” (➔ 54) and an input selector other than HDMI is selected.

Speaker Settings

If you change these settings, you must run Audyssey MultEQ Room Correction and Speaker Setup again (➔ 29).

If the impedance of any speaker is 4 ohms or more but less than 6, set the minimum speaker impedance to 4 ohms. If you bi-amp the front speakers, you must change the “Speakers Type(Front)” setting (➔ 44).

For hookup information, see “Bi-amping the Front Speak- ers” (➔ 16).

Note

•When bi-amping is used, the AV receiver is able to drive up to 5.1 speakers in the main room.

•Before you change these settings, turn down the volume.

■Speaker Impedance

`4ohms:

Select if the impedance of any speaker is 4 ohms or more but less than 6.

`6ohms:

Select if the impedances of all speakers are between 6 and 16 ohms.

■Speakers Type(Front)

`Normal:

Select this if you’ve connected your front speakers normally.

`Bi-Amp:

Select this if you’ve bi-amped your front speakers.

Note

•Powered Zone 2 cannot be used if “Speakers Type(Front)” is set to “Bi-Amp” (➔ 69).

■Powered Zone2

See “Setting the Powered Zone 2” (➔ 69).

This setting is set automatically by Audyssey MultEQ Room Correction and Speaker Setup function (➔ 29).

With these settings, you can specify which speakers are connected and a crossover frequency for each speaker. Specify “Full Band” for speakers that can output low fre- quency bass sounds adequately, for example, speakers with a good sized woofer. For smaller speakers, specify a crossover frequency. Sounds below the crossover fre- quency will be output by the subwoofer instead of the speaker. Refer to your speaker’s manuals to determine the optimum crossover frequencies. If you set up your speak- ers using Audyssey MultEQ Room Correction and Speaker Setup, please make sure manually that any THX speakers are set to “80Hz(THX)” crossover.

■Subwoofer

`Yes:

Select if a subwoofer is connected.

`No:

Select if no subwoofer is connected.

■Front

`Full Band

`40Hz to 80Hz(THX) to 100Hz, 120Hz, 150Hz,

200Hz

Note

•If the “Subwoofer” setting is set to “No”, the “Front” setting is fixed at “Full Band”.

■Center*1, Surround*1, Surr Back*2*3*4*5

`Full Band

`40Hz to 80Hz(THX) to 100Hz, 120Hz, 150Hz,

200Hz

`None:

Select if no speaker is connected.

■Front Wide*1*2*4*6, Front High*1*2*4*5

`Full Band

`40Hz to 80Hz(THX) to 100Hz, 120Hz, 150Hz,

200Hz

`None:

Select if no speaker is connected.

Note

*1	“Full Band” can be selected only when “Full Band” is
	selected in the “Front” setting.
*2	If the “Surround” setting is set to “None”, this setting cannot
	be selected.
*3	If the “Surround” setting is set to anything other than “Full
	Band”, “Full Band” cannot be selected here.
*4	If the “Speakers Type(Front)” setting is set to “Bi-Amp”
	(➔ 44), this setting cannot be selected.
*5	If the Powered Zone 2 is being used (➔ 69), this setting can-
	not be selected.
*6	If the “Powered Zone 2” setting is set to “Act” (➔ 69), this
	setting cannot be selected.

En

44