JVC DLA-M4000LU manual Operating the Main Menu

Page 31

Operating the Main Menu

Configuration the Main Menu (AV Input) For computer inputs, see the following page.

You can adjust video quality (PICTURE) and etc. using the menus.

The menus are configured as follows:

Main menu (AV inputs : During EXT. IN input signal)

PIXEL CLOCK

POSITION

PICTURE

TRACKING

: Normally, no adjustment is required. The lateral size and display area of video image are adjusted.

PHASE

: Normally, no adjustment is required. Flickering or dim video image is adjusted.

 

 

V. POS.

: The vertical position of the video image being projected is adjusted.

H. POS.

: The horizontal position of the video image being projected is adjusted.

BRIGHTNESS

: The brightness of the video image being projected is adjusted.

CONTRAST

: The contrast of the video image being projected is adjusted.

SHARPNESS

: The sharpness of the video image being projected is adjusted.

COLOR

: The color density of the video image being projected is adjusted.

TINT

: The tint of the video image being projected is adjusted. (Displayed only for NTSC signal)

ALL RESET

: All the items adjusted are reset.

OPTIONS

MENU AUTO OFF : Sets whether to turn off menu display automatically (YES) or not (NO).

LINE DISPLAY

: Sets whether to make the line display effective (ON) or not (OFF) for about 5 seconds after input

 

switching.

RIGHT LEFT REV. : Video image is reversed right-to-left.

TOP BOTTOM INV. : Video image is inverted top-to-bottom.

CLAMP

: Sets the clamp pulse’s position at the back porch (BP) or on the sink tip (ST). Normally, the clamp

 

pulse is used at BP. If, with some PCs or workstations, the screen becomes unstable such as

 

being too dark or too bright, try to switch to ST.

RESIZE

: Does not work with AV (video) input. (RESIZE is shown in gray.)

BACK COLOR

: Specifies the background color when there is no video signal. Background color can be selected

 

from BLUE, CYAN, BLACK, GREEN, MAGENTA, RED, and YELLOW.

COLOR TEMP.

: Adjusts the color temperature of the image being projected. Make adjustment when the image

 

becomes reddish or bluish.

 

Color temperature can be set to LOW, MIDDLE, or HIGH.

ASPECT CHANGE : Selects the vertical-to-horizontal ratio of the image projected. The factory-set ratio is 4 : 3. When

 

projecting high-vision video image, a ratio of 16 : 9 can be selected.

SLEEP TIME

: Sets the length of sleep time. A set sleep time after input signal is depleted, the projector goes into

 

a stand-by state. Sleep time can be selected from 10 minutes, 20 minutes, 30 minutes, 60 minutes

 

and 0 minutes. (If you select 0 minutes, the sleep time will be cleared.)

LAMP TIME

: Indicates the accumulated used hours of the light-source lamp.

SOURCE

CHANNEL

USER SOURCE SET UP

DISPLAY SIZE

DECODER

:Normally used in AUTO. If use in AUTO is unstable such as color not appearing, the screen being disturbed or the screen being intermitted, set to the dedicated source (forced mode) in accordance with the input signal.

USER allows you to set a source which is uniquely adjusted by the user.

:Sets a line and multiple sources for each channel.

:Sets up an area for the source being input, and registers the user name.

:This does not work for AV [EXT. IN (VIDEO, Y/C, YPBPR)] input signals. (Adjustment items are displayed in gray color).

: Normally, set to AUTO. The color system of an input signal is automatically identified and shown in ( ). When use in AUTO is unstable such as no color being shown, set the dedicated color system in accordance with the input signal. You can select from AUTO, NTSC(480i), NTSC4.43, PAL, and SECAM.

LANGUAGE

:Text on the screen can be changed to a language other than English. Languages that can be displayed are the

following six : (Japanese), ENGLISH, DEUTSCH (German), ESPAÑOL (Spanish), ITALIANO (Italian), and FRANÇAIS (French). However, some text such as “QUICK-ALIGNMENT”, etc. are shown only in English.

31

Page 30 Page 32
Image 31
Page 30 Page 32
Contents Serial No For customer UseAbout burning-in of the D-ILA device Safety PrecautionsDo not allow any unqualified person to install the unit Safety PrecautionsContents Video board AccessoriesInformation on separately sold items Projection lensFront Side / Top Surface / Right Side Controls and FeaturesControl panel Left-hand side / Back SideExhaust vents Vents for cooling fans through which warm air comes outControl Panel RGB button When a menu is shownSetting button AV buttonConnector Panel Remote Control Unit AV Hide button Lens Lock Ô Unlock switchPreset button AV button Quick ALIGN. Quick Alignment buttonOpen the back cover Installing BatteriesInstall the batteries Menu / Enter Menu Operation ButtonAllowable minimum space required Installing the ProjectorPrecautions for Installation When installing the projector, observe the followingsReflected light Relationship relative to Glass SurfaceOr more Center line of the lens Lens Shift FunctionChange of projection screen according to aspect ratio ScreenMaximum amount of shift Relational table for maximum shift amounts aspect ratio 4Projection Distances and Screen Sizes Adjustable range of the lensRelationship of screen size vs. projection distance Computer signals Connecting to Various DevicesSignals that Can Be Input to the Projector Video signalsAlso, read the manuals which came with the equipment Examples of System ConfigurationRGB switcher Projector Computer Example of a basic systemDesktop type Connecting to Computer DevicesRGB output devices Remote control cable Connecting to Devices which Control the ProjectorRemote control when remote control cable is used To remote controlRemove the lens cap Connecting the Power Cord SuppliedRemove the power input terminal cover To use the projectorWhen Turning On the Devices Connected to the Projector Stopped running Turning on the PowerTurning off the Power Basic OperationsFor setting the source, see Adjust the screen sizeWhen you press Video When you press Computer¶ For Operating Other Functions Adjust focusAdjust focus with the remote control’s Focus +/- buttons When using the projector To clear the main menu To display the Setting menu Projector’s button To display the Main menuTo temporarily erase video image To use the remote control’s Preset buttonPress AV Hide on the remote control To display Channel on the screenPress the Setting button to select the desired item Operating the Setting MenuMaking Basic Settings Press the Setting button of the projectorOperating the Main Menu Configuration of the Main Menu Computer-related input Press the MENU/ENTER button Remote control unitSet adjust the item Operating the Main Menu Basic Operation of the Main MenuPress the MENU/ENTER button Changing the Color SystemAbout language display Changing the Language DisplayPress the MENU/ENTER button Language displayAdjustment item Button Adjustment content Adjusting the Pixel ClockMain menu appears on the screen Adjusting the Screen PositionWhen AV signals are input Adjusting Picture QualityWhen computer-related signals are input For computer system input To adjust multiple items, repeat steps 4Submenu items For video system inputButton Adjustment content Submenu item Options Setting and Adjusting Other Functions OptionsFollowing optional functions can be set adjusted Submenu items of the Options menu are displayedOptions menu Display, the video image resolution becomes coarseAspect Selected item text display is shown in magenta color Changing Setting the SourceInput mode Factory setting Selected item displayed in text is shown in magenta colorPress MENU/ENTER to set fix When a source setting Dedica TED Source isSource setup menu SubmenuSelect a user area When a source setting User is selectedUser Source setup menu is displayed Press MENU/ENTER toward the 5 or ∞ mark toPress the MENU/ENTER button to set Setting Up ChannelsPress MENU/ENTER to set Line selection menu Setting Up Channels Line setupWhen Line is selected Line selection menu screen appearsWhen Source is selected Setting Up Channels Source setupSource registration screen appears Press the MENU/ENTER button Press the page Back button to set Setting Up Channels SWNo. setupSwitcher number setup menu is displayed Switcher No. setting menuDisplayed To switch channels using aDIRECT ChannelChanging Channels CH Change Press page Back while no menu isChannel are selected Want to switch toLine input, source and switcher number registered to Mark to select the channel CH youSubmenu item User Source SET UP Setting Up or Changing User SourcesConnection Screen User Source setup menuSubmenu item, User Source Setup menu , appears on Press MENU/ENTER toward the 3mark to select the User NameTo delete a user name, overwrite the user name with spaces Repeat steps 1 and 2 to enter the user nameTo adjust other items, repeat steps 4 Setting Up or Changing the Display SizePress MENU/ENTER toward the 2or 3 mark to adjust the item Display Size adjustment menuAdjustment item Contents of adjustment There are two filters used Cleaning and Replacing the FilterRemove the filter cover screws Remove the filtersReinstall the filters Clean the filtersAbout Light-Source Lamp Replacement Troubleshooting Troubleshooting Does not work When the emergency indicator starts blinkingRemote control unit Is not possibleEXT. in AV in input SpecificationsRGB in RGB input 7Vp-p, 75Ω Horizontal sync/composite sync signal H/CsVertical sync signal Line, D-sub 3-row 15-pin ⋅Front Outside dimensionsDTV-format signals TopComputer IN-1 PC / Computer OUT Terminal Pin assignment Specifications for terminalsTerminal RS-232C terminalV-Ni LCT0634-001D
Related manuals
Manual 44 pages 4.94 Kb
Top Page Image Contents