Knoll Systems HT200 user manual

Page 15
7) Change the unit setting to suit to the projecting method and selected source as described in step 4.
• Select the type of projection
If the projected image is horizontally reversed or upside down, change the projection type. See page 19.
• If the component video signal output jacks of the video component are connected to the
RGB IN connector (see page 10), set "INPUT MODE" to YCbCr" in the menu. This setting can provide a better picture image. See page 20.
• Adjust the projected image from the source connected to the RGB IN connector. The resolutions most suitable to the incoming signals will automatically be selected. However, if any vertical banding, noise, dot interference, or crosstalk appears on the screen, adjust "PICTURE ADJ," then "FINE PICTURE" using the menus. You can also adjust the horizontal and vertical position of the image. See page 20.
6) Adjust the picture elements and select the picture type.
You can adjust the picture elements (see page 24); select the picture type according to the video contents (see page 25) and wide screen (see page 25).
7) Start using the Projector.
The following functions are available while using the Projector:
• Adjusting the volume of the unit speaker (see pages 19),
• Using the laser pointer (see page 17),
• Turning off the image and muting the sound temporarily (see page 17),
• Freezing a moving picture (see page 17), and
• Enlarging the picture (see page 17).
Note
If "POWER OFF" is set to "ON" (see page 25), the image will be turned off if the unit has been projecting a blank screen for five minutes with an RGB input source.
If the image is suddenly turned off while projecting a computer image, the computer's screen saver or the unit's POWER OFF function may be activated.
Turning the Projector off 1)
Operating with the remote control: Press the POWER OFF button a little bit longer. Operating with the projector keypad 1. Press the POWER button.
"POWER OFF/ENTER" appears on the screen.
2. Press ENTER
When the projector is turned off, the POWER indicator will start blinking then turn to amber in about one minute.
***Never turn off the POWER switch (main power) while the POWER indicator is blinking.***
To cancel turning off the unit when "POWER OFF/ENTER" is appearing on the screen See "Canceling turning off the unit when "POWER OFF/ENTER" is appearing on the screen" on page 25.
Please also read "Activating the on-screen function" on page 25.
2) If the POWER indicator is lit in amber, press the "O" side of the POWER switch (main power) on the projector back.
The POWER indicator goes out.
Disconnect the power cord if it is not to be used for an extended period.
15
Page 14 Page 16
Image 15
Page 14 Page 16
Contents HT200 Lamp Replacement InstallationPower Supply CleaningTable of Contents Basic HT200 Information Congratulations On Your Purchase of the HT200 ProjectorSharp, clear images Remote Control Remote control effective rangeInserting the batteries Terminal Connection Panel Projector Part Identification Installation Carrying The ProjectorProjector Positioning Projection Distance Projection Distance 43 Video ScreenBefore connecting Connecting Video EquipmentBefore connecting Before connecting Connecting a PC or MacintoshModifying the DIP switch for Macintosh setting Macintosh adapter cable DIP switch setting o=ONSome examples of DIP switch settings Before starting Operation Using the ProjectorTurn on the connected source computer, VCR, DVD player, etc When the projected image is offset horizontallyWhen the projected image is offset vertically Using the adjusters to adjust the height balancePage Windows MethodMacintosh Freezing a moving picture Adjusting the volume of the projector speakerUsing the laser pointer Turning off the image and muting the sound temporarilyCursor up or down key Remote control buttons Projector operation buttonsPress the cursor up or down to select Source Menu Source menu appears on the screenAdjusting the volume Selecting a display languageSelecting the background Quick starting the projector Setting Input Mode to YCbCr or Component VideoTiming Chart Signal Resolution Sync Dot Clock KHz MHz Adjusting the clock frequency Adjusting the clock phaseWhen you have connected another computer or video component Resetting the present settings to factory settings Selecting the starting mode for the next projector useInput source Adjusting the picture elementsInput Mode see Selecting the picture typeActivating the power saving function Selecting the wide screen displayActivating the on-screen function Checking hours of lamp use Resetting all to the factory settingsResetting the lamp use hours to zero Turning the projector off with on screen functionsMechanical SpecificationsOptical ElectricalCommon Problems & Solutions TroubleshootingStatus Light Message Replacing the lamp housingLamp housing replacement procedure

HT200 specifications

The Knoll Systems HT200 is a sophisticated home theater receiver widely recognized for its blend of advanced audio technologies and user-friendly features. This model is part of Knoll Systems' commitment to delivering high-quality sound and video experiences in residential settings.

One of the standout features of the HT200 is its powerful amplification capabilities. It utilizes a robust multi-channel amplifier that can deliver high wattage per channel, ensuring clear, dynamic sound even at high volumes. This is particularly advantageous for audiophiles and movie enthusiasts who seek an immersive audio experience. The incorporation of high-quality DACs (Digital-to-Analog Converters) further enhances sound fidelity, providing a richer and more accurate audio reproduction.

The HT200 supports a wide range of audio formats, including traditional stereo as well as surround sound formats like Dolby Atmos and DTS:X. This versatility allows users to enjoy a cinematic experience from the comfort of their homes. The receiver can decode these advanced formats, providing users with the ability to create a multi-dimensional audio environment.

In terms of connectivity, the HT200 is equipped with multiple HDMI inputs, allowing it to integrate seamlessly with various devices like Blu-ray players, gaming consoles, and streaming devices. It also supports 4K and HDR video pass-through, ensuring that users can enjoy high-quality visuals without any compromise. Additional connectivity options include Bluetooth, Wi-Fi, and even USB ports, which cater to diverse multimedia sources.

The user interface of the HT200 is designed with accessibility in mind. It offers an intuitive on-screen menu that simplifies the setup process and provides easy navigation. Furthermore, the receiver supports mobile app control, allowing users to manage settings and playback remotely through their smartphones or tablets.

Another notable characteristic of the HT200 is its customizable sound settings. Users can adjust parameters such as equalization and speaker placement, ensuring an optimized audio experience tailored to their specific room acoustics. This level of personalization makes the HT200 an appealing choice for home theater enthusiasts looking to maximize their audio experience.

In summary, the Knoll Systems HT200 is a feature-rich home theater receiver that combines powerful amplification, advanced audio processing, and extensive connectivity options. With its user-friendly interface and customizable sound settings, it stands out as an excellent choice for anyone looking to elevate their home entertainment experience.
Top Page Image Contents