Onkyo TX-DS696 Level Calibration submenu, About the other settings, Press the jog dial again

Page 24

Speaker setup

Level Calibration submenu

This submenu allows you to set the volume levels of each speaker individually so that they all sound at the same level when heard from the listening position. If you are continuing from setting the speaker distances and are still in the setting mode, skip directly to step 2.

1. Press the SETUP button.

SETUP

If a menu other than “1. Speaker Setup” appears, turn the jog dial until “1. Speaker Setup” does appear.

2.Press the jog dial and then turn it to display the “Level Cal?”

DSP/MODE ADJ

DSP/MODE ADJ

PUSH TO ENTER

PUSH TO ENTER

3. Press the jog dial.

DSP/MODE ADJ

 

A test sound (pink noise) will be heard from

 

the left front speaker. At this point, it is not

 

necessary to adjust the volume of the test

PUSH TO ENTER

sound.

 

 

db

4. Press the jog dial again.

DSP/MODE ADJ

 

The test sound will now be heard from a

 

different speaker.

PUSH TO ENTER

 

5. Turn the jog dial to adjust the

DSP/MODE ADJ

 

volume of the test sound from this

 

speaker to the same level that you

 

heard from the previous speaker.

PUSH TO ENTER

 

6.Repeat the procedure in step 4 and 5 until the volume of the test sound from all speakers is the same level.

Each time you press the jog dial, the test sound will be heard

from a different speaker. The speaker order for calibration is front left → center → front right → surround right → surround left → subwoofer.

7.Press the RETURN button.

You return to the “Level Cal?” display.

Notes:

•If you press the RETURN button again, you go back up one more level.

•To exit the setting mode immediately, press the SETUP button.

About the other settings

The factory settings for your TX-DS696 are given in the table on page 12. If you connect your system in accordance with these factory settings, there is no need to change them. However, if you do not, you will need to change the settings that do not match. If you do not, signals may not be properly received resulting in poor sound or image quality, no digital output, or no output at all.

Changing a digital input setting:

1.Press the input selector button for the source that you want to change.

2.Press the SETUP button.

3.Turn the jog dial to display “2. Input Setup.”

4.Press the jog dial.

“Audio Setup?” appears.

5.Press the jog dial again.

“D.Input: xxx” appears.

6.Turn the jog dial and select the connector to which the digital source is connected.

7.Press RETURN repeatedly or press SETUP to exit the setting mode.

Changing the multichannel setting:

1.Press the input selector button for the source that you want to change.

2.Press the SETUP button.

3.Turn the jog dial to display “2. Input Setup.”

4.Press the jog dial.

“Audio Setup?” appears.

5.Press the jog dial twice.

“Multich: xxx” appears.

6.Turn the jog dial to select “Yes” or “No.”

7.Press RETURN repeatedly or press SETUP to exit the setting mode.

Changing the Component Video Input setting:

1.Press the input selector button for the source that you want to change.

2.Press the SETUP button.

3.Turn the jog dial to display “2. Input Setup.”

4.Press the jog dial.

“Audio Setup?” appears.

5.Turn the jog dial to display “Video Setup?”

6.Press the jog dial.

“Cmponent: xxx” appears.

7.Turn the jog dial to select the connectors to which the source is connected (“Input 1” or “Input 2”).

8.Press RETURN repeatedly or press SETUP to exit the setting mode.

24

Page 23 Page 25
Image 24
Page 23 Page 25
Contents TX-DS696 Important Safeguards AvisPrecautions Contents Contents Features Supplied accessoriesBefore using this unit Setting the Voltage selector Worldwide models onlyUsing the remote controller Installing the remote controller batteriesFront panel facilities Front panelFront panel display Front panel facilities Remote controller Remote controller Connecting power amplifiers Voltage selector ConnectionsImproper connection Inserted completely Optical digital input terminalConnecting your audio components Connecting a turntable PhonoConnecting a compact disc player CD ConnectionsConnecting your video components Flow of the video signals is as followsConnecting a DVD player DVD Audio connection cable Left White Video connection cableConnecting a video cassette recorder Video Connecting a satellite tuner or television VideoConnecting a television monitor or projector Connecting settop box or video camera, etc. VideoConnecting power amplifiers Power on/ready functionPower off function Connect to devices with z terminalsConnecting speakers Positioning speakers Connecting speakersStandard speaker placement Check the impedance of the speakers you are connectingConnecting speakers Connecting the speaker cable Connecting a subwooferConnecting the remote zone speakers 345Connecting the power Connecting antennas Connecting the AM antenna cableConnecting the included antennas Assembling the AM loop antennaConnecting antennas Connecting an FM outdoor antennaConnecting an AM outdoor antenna Directional linkageSpeaker setup Speaker Configuration submenuPress the Setup button Buttons to be usedSpeaker setup Speaker Distance submenuAbout the other settings Turn the jog dial to adjustLevel Calibration submenu Press the jog dial againTuning into a radio station Listening to a stereo radio station FM modeListening to Radio Broadcasts Presetting a radio station Selecting a preset radio stationErasing a preset radio station Listening to Radio BroadcastsWhat is RDS? Listening to RDS broadcasts European models onlyListening to RDS broadcasts PTY program types in EuropeListening to RDS broadcasts Displaying Radio Text RTPerforming a TP scan Performing a PTY scanAdjusting the bass and treble Listening with headphonesEnjoying music or videos with the TX-DS696 Temporarily turning off the soundSwitching the display Adjusting the brightness of the front displayUsing the sleep time remote controller only Enjoying music or videos with the TX-DS696Changing the audio mode Using the tone controlAdjust the tone using the Bass and Treble dials Enjoying the multichannel outputUsing listening mode Listening modesUsing listening mode Changing the listening modeUsing Cinema Re-Equalization Listening Mode Buttons Re-EQSetup menus Main menuMenu Sub menuSetup menus Navigating through the Setup menuSetting procedures and button operations Speaker Setup menu TipSpeaker Config sub-menu Speaker Distance sub-menuLevel Calibration sub-menu Calibrating the speaker levelsInput Setup menu InputSource Audio Setup sub-menu Video Setup sub-menuDigital Input MultichannelListening Mode Preset sub-menu IntelliVolume sub-menu Input source signalsIntelliVolume Analog/PCM SourceListening Mode Setup menu Description listening mode parametersRelationship between listening mode and parameter Front EffectVolume Setup sub-menu Headphones Level sub-menuLate Night Setup sub-menu AM Freq Step Setup sub-menu Worldwide model onlyOSD Setup menu OSD Setup sub-menuOSD Config sub-menu OSD Position sub-menuRecording Recording the input source REC OUT selectorRecording both the audio and video Recording a source different from that you are listening toEnjoying music in the remote zone Using remote controller Calling up a preset radio stationOverview Controlling an Onkyo cassette tape deckUsing remote controller Press the CD Mode buttonDisc Stdby CD Mode Controlling an Onkyo CD playerPress the DVD Mode button Return DVD ModeControlling an Onkyo DVD player Disc VOL TOP Menu Audio Muting Angle Subtitle DVDSAT, CABLE, VCR, and TV Mode buttons Press the MD Mode buttonControlling an Onkyo MD recorder To 9, 0, --/--- Numeric keysSEND/LEARN indicator Buttons that Learning a pre-programming codeLearning a pre-programming code Within 30 seconds, enter the 3-digit code numberLearning a pre-programming code Pre-programmong codesOperating your programmed remote controller DVD Mode DVD Player ModeSAT Mode Satellite Tuner Mode Cable Mode Cable Tuner ModeOperating your programmed remote controller VCR Mode VCR ModeTV Mode TV Mode Press the VCR Mode buttonProgramming procedure Mode Direct Mode MacroSEND/LEARN LightPage Erasing the programmed command from one button Erasing all the commands programmed under a Mode buttonPress and release the same Mode button again SEND/LEARN indicator Mode buttonsUsing a Macro function What is a Macro function?Press the Mode Macro button to complete the programming Programming a Macro functionUsing a Macro function Programming the Direct Macro functionRunning a Direct Macro function Erasing a macro from the Mode Macro button Press the Mode Macro button againDirect Macro Mode buttons Erasing a direct macro from the Direct Macro buttonErasing all commands and macros that have been programmed Macro mode programming memoPress the Enter button OperationSpecifications Amplifier SectionTroubleshooting guide Troubleshooting guide Video and AudioIf one of the messages shown below appears Onkyo U.S.A. Corporation Onkyo Europe Electronics GmbHOnkyo China Limited

TX-DS696 specifications

The Onkyo TX-DS696 is a powerful and versatile home theater receiver that has left a significant mark in the world of audio and video entertainment. Launched to cater to audiophiles and home cinema enthusiasts, this receiver is known for its robust performance, extensive connectivity options, and user-friendly features, making it a popular choice among consumers.

At the heart of the TX-DS696 is its impressive multichannel processing capabilities. Supporting Dolby Digital and DTS surround sound formats, it delivers immersive audio experiences that enhance the enjoyment of movies, music, and games. The 5.1 channel configuration allows for exceptional sound staging, giving users a truly cinematic experience right in their living rooms.

One of the standout features of the TX-DS696 is its advanced room calibration technology. The receiver analyzes the acoustic characteristics of the room and adjusts the speaker settings accordingly, optimizing sound quality for any space. This ensures that listeners can enjoy a balanced audio performance regardless of their room’s layout or size.

Connection options are plentiful, with multiple audio and video inputs that facilitate direct connections to various devices. The receiver includes several composite and S-Video inputs, along with digital optical and coaxial inputs, allowing users to connect DVD players, gaming consoles, and other multimedia devices easily. The support for component video ensures high-quality image transfer, making it an excellent choice for those who want to enjoy high-definition video.

In terms of power, the TX-DS696 boasts a robust amplifier section capable of delivering rich and dynamic sound across all channels. The built-in high-current amplification technology ensures that even demanding speakers are driven effortlessly, resulting in clean and distortion-free audio at all volume levels.

The user interface is intuitive, with an easy-to-read LCD display and a well-laid-out remote control that provides convenient access to all the receiver’s functions. Additionally, the Onkyo TX-DS696 is compatible with various external devices, allowing for custom configurations that cater to personal preferences.

Overall, the Onkyo TX-DS696 stands out as an exemplary home theater receiver that combines advanced technology, user-friendly features, and powerful performance. Whether you’re a dedicated home theater enthusiast or a casual listener, this receiver offers a rich audio experience that is hard to match. Its blend of performance, versatility, and value makes it a lasting favorite in the realm of home audio systems.
Top Page Image Contents