Onkyo TX-DS696 Using a Macro function, What is a Macro function?, Programming a Macro function

Page 57

Using a Macro function

What is a Macro function?

A Macro function enables you to program a series of button operations (up to 16) on the remote controller into a single button. For example, to play a compact disc player connected to the TX- DS696 normally, you must perform the following steps:

1.Press the RCVR MODE button.

2.Press the ON button.

3.Press the CD (INPUT SELECTOR) button.

4.Press the CD MODE button.

5.Press the playback () button.

By using the macro function, you can perform the above five operations by only pressing two buttons.

ON

MODE MACRO

RCVR MODE CD MODE

(CD playback)

CD

(INPUT

SELECTOR)

HOME THEATER CONTROLLER

RC-440M

Tips:

•If you erase or change the command of a button programmed in a macro, that operation of that button will no longer work in the macro. In this case, it will be necessary for you to reprogram the macro in order to avoid incorrect operation.

•The codes programmed into a macro will be transmitted at an interval of 0.5 seconds. However, some devices may not be able to complete one operation in 0.5 seconds and may miss the next code. In this case, after pressing one operation button, you can press the same MODE button again before pressing the next operation button to add another 0.5 seconds between the two operations.

Programming a Macro function

You can program a different macro into the MODE MACRO button for each of the eight MODE buttons. The macro is then executed by pressing the appropriate MODE button and then pressing the MODE MACRO button. For example, to program the macro described above into the CD MODE button, perform the steps given below.

1.Press and hold down the desired MODE button (in this case, the CD MODE button), press the MODE MACRO button, and then release both buttons.

When you press the CD MODE button, the SEND/LEARN indicator lights and the CD MODE button lights green. When you press the MODE MACRO button, the indicator turns off. When you release the buttons, the indicator flashes and lights again.

2.Press the operation buttons you wish to program in order (in this case, press RCVR MODE → ON → CD (INPUT SELECTOR) → CD MODE → playback () button).

When you press each button, the SEND/LEARN indicator turns off. When you release the button, the indicator lights.

3.Press the MODE MACRO button to complete the programming.

The SEND/LEARN indicator flashes twice slowly.

4.Run the macro to check to see if the macro has been properly programmed.

Notes:

•You may program up to 16 button operations into each macro function. If you try to program a 17th operation, it will be ignored, and programming is stopped.

•If no button is pressed for more than 30 seconds during the programming, the SEND/LEARN indicator flashes three times quickly, and the remote controller exits the programming mode. Resume from Step 1.

•If you perform an invalid operation during programming, the SEND/LEARN indicator flashes three times quickly, and the remote controller exits the programming mode. Resume from Step 1.

Running a Macro function

Perform the procedure below to run a macro function that you have programmed into the remote controller. After programming a macro, you should always run it at least once to make sure that it has been programmed properly.

1.Point the remote controller at the TX-DS696 and press the CD MODE button.

2.Press the MODE MACRO, and verify that the devices operate properly.

It may take a while for the macro to finish transmitting, so be sure to continue pointing the remote controller at the device until the SEND/LEARN indicator turns off.

57

Page 56 Page 58
Image 57
Page 56 Page 58
Contents TX-DS696 Avis Important SafeguardsPrecautions Contents Contents Supplied accessories FeaturesSetting the Voltage selector Worldwide models only Before using this unitUsing the remote controller Installing the remote controller batteriesFront panel facilities Front panelFront panel display Front panel facilities Remote controller Remote controller Connections Connecting power amplifiers Voltage selectorImproper connection Inserted completely Optical digital input terminalConnecting a turntable Phono Connecting your audio componentsConnecting a compact disc player CD ConnectionsFlow of the video signals is as follows Connecting your video componentsConnecting a DVD player DVD Audio connection cable Left White Video connection cableConnecting a satellite tuner or television Video Connecting a video cassette recorder VideoConnecting a television monitor or projector Connecting settop box or video camera, etc. VideoPower on/ready function Connecting power amplifiersPower off function Connect to devices with z terminalsPositioning speakers Connecting speakers Connecting speakersStandard speaker placement Check the impedance of the speakers you are connectingConnecting the speaker cable Connecting a subwoofer Connecting speakersConnecting the remote zone speakers 345Connecting the power Connecting the AM antenna cable Connecting antennasConnecting the included antennas Assembling the AM loop antennaConnecting an FM outdoor antenna Connecting antennasConnecting an AM outdoor antenna Directional linkageSpeaker Configuration submenu Speaker setupPress the Setup button Buttons to be usedSpeaker Distance submenu Speaker setupTurn the jog dial to adjust About the other settingsLevel Calibration submenu Press the jog dial againTuning into a radio station Listening to a stereo radio station FM modeListening to Radio Broadcasts Selecting a preset radio station Presetting a radio stationErasing a preset radio station Listening to Radio BroadcastsListening to RDS broadcasts European models only What is RDS?Listening to RDS broadcasts PTY program types in EuropeDisplaying Radio Text RT Listening to RDS broadcastsPerforming a TP scan Performing a PTY scanListening with headphones Adjusting the bass and trebleEnjoying music or videos with the TX-DS696 Temporarily turning off the soundAdjusting the brightness of the front display Switching the displayUsing the sleep time remote controller only Enjoying music or videos with the TX-DS696Using the tone control Changing the audio modeAdjust the tone using the Bass and Treble dials Enjoying the multichannel outputListening modes Using listening modeChanging the listening mode Using listening modeUsing Cinema Re-Equalization Listening Mode Buttons Re-EQMain menu Setup menusMenu Sub menuSetup menus Navigating through the Setup menuSetting procedures and button operations Tip Speaker Setup menuSpeaker Distance sub-menu Speaker Config sub-menuLevel Calibration sub-menu Calibrating the speaker levelsInput Setup menu InputSource Video Setup sub-menu Audio Setup sub-menuDigital Input MultichannelInput source signals Listening Mode Preset sub-menu IntelliVolume sub-menuIntelliVolume Analog/PCM SourceDescription listening mode parameters Listening Mode Setup menuRelationship between listening mode and parameter Front EffectHeadphones Level sub-menu Volume Setup sub-menuLate Night Setup sub-menu AM Freq Step Setup sub-menu Worldwide model onlyOSD Setup sub-menu OSD Setup menuOSD Config sub-menu OSD Position sub-menuRecording the input source REC OUT selector RecordingRecording both the audio and video Recording a source different from that you are listening toEnjoying music in the remote zone Calling up a preset radio station Using remote controllerOverview Controlling an Onkyo cassette tape deckPress the CD Mode button Using remote controllerDisc Stdby CD Mode Controlling an Onkyo CD playerReturn DVD Mode Press the DVD Mode buttonControlling an Onkyo DVD player Disc VOL TOP Menu Audio Muting Angle Subtitle DVDPress the MD Mode button SAT, CABLE, VCR, and TV Mode buttonsControlling an Onkyo MD recorder To 9, 0, --/--- Numeric keysLearning a pre-programming code SEND/LEARN indicator Buttons thatLearning a pre-programming code Within 30 seconds, enter the 3-digit code numberPre-programmong codes Learning a pre-programming codeDVD Mode DVD Player Mode Operating your programmed remote controllerSAT Mode Satellite Tuner Mode Cable Mode Cable Tuner ModeVCR Mode VCR Mode Operating your programmed remote controllerTV Mode TV Mode Press the VCR Mode buttonMode Direct Mode Macro Programming procedureSEND/LEARN LightPage Erasing all the commands programmed under a Mode button Erasing the programmed command from one buttonPress and release the same Mode button again SEND/LEARN indicator Mode buttonsWhat is a Macro function? Using a Macro functionPress the Mode Macro button to complete the programming Programming a Macro functionUsing a Macro function Programming the Direct Macro functionRunning a Direct Macro function Press the Mode Macro button again Erasing a macro from the Mode Macro buttonDirect Macro Mode buttons Erasing a direct macro from the Direct Macro buttonMacro mode programming memo Erasing all commands and macros that have been programmedPress the Enter button OperationAmplifier Section SpecificationsTroubleshooting guide Troubleshooting guide Video and AudioIf one of the messages shown below appears Onkyo U.S.A. Corporation Onkyo Europe Electronics GmbHOnkyo China Limited

TX-DS696 specifications

The Onkyo TX-DS696 is a powerful and versatile home theater receiver that has left a significant mark in the world of audio and video entertainment. Launched to cater to audiophiles and home cinema enthusiasts, this receiver is known for its robust performance, extensive connectivity options, and user-friendly features, making it a popular choice among consumers.

At the heart of the TX-DS696 is its impressive multichannel processing capabilities. Supporting Dolby Digital and DTS surround sound formats, it delivers immersive audio experiences that enhance the enjoyment of movies, music, and games. The 5.1 channel configuration allows for exceptional sound staging, giving users a truly cinematic experience right in their living rooms.

One of the standout features of the TX-DS696 is its advanced room calibration technology. The receiver analyzes the acoustic characteristics of the room and adjusts the speaker settings accordingly, optimizing sound quality for any space. This ensures that listeners can enjoy a balanced audio performance regardless of their room’s layout or size.

Connection options are plentiful, with multiple audio and video inputs that facilitate direct connections to various devices. The receiver includes several composite and S-Video inputs, along with digital optical and coaxial inputs, allowing users to connect DVD players, gaming consoles, and other multimedia devices easily. The support for component video ensures high-quality image transfer, making it an excellent choice for those who want to enjoy high-definition video.

In terms of power, the TX-DS696 boasts a robust amplifier section capable of delivering rich and dynamic sound across all channels. The built-in high-current amplification technology ensures that even demanding speakers are driven effortlessly, resulting in clean and distortion-free audio at all volume levels.

The user interface is intuitive, with an easy-to-read LCD display and a well-laid-out remote control that provides convenient access to all the receiver’s functions. Additionally, the Onkyo TX-DS696 is compatible with various external devices, allowing for custom configurations that cater to personal preferences.

Overall, the Onkyo TX-DS696 stands out as an exemplary home theater receiver that combines advanced technology, user-friendly features, and powerful performance. Whether you’re a dedicated home theater enthusiast or a casual listener, this receiver offers a rich audio experience that is hard to match. Its blend of performance, versatility, and value makes it a lasting favorite in the realm of home audio systems.
Top Page Image Contents