Onkyo TX-DS696 appendix Troubleshooting guide

Page 62

Troubleshooting guide

If a problem occurs while you are using the remote controller, first try to operate the controls on the front panel of the TX-DS696 to make sure that it is not due to a malfunction (or worn out batteries) in the remote controller.

POWER

Power shuts off immediately after power on.

•Amplifier protection circuitry has been activated.

➞Remove the power cord from outlet immediately. Contact your Onkyo service center.

No power.

•Power cord is disconnected.

➞Connect power cord.

•External noise in the affecting the internal microcomputer.

➞Turn the power button off and then on again or remove the power cord from the outlet and then plug it in again.

•Internal fuse is blown.

➞Contact your Onkyo Service Center.

Power turns on but no sound.

•“Muting” is displayed.

➞Press the MUTING button on the remote controller to turn it off.

•Bad connections or wiring.

➞Check connections, speaker cables, etc.

•Amplifier protection circuitry has been activated.

➞Contact your Onkyo Service Center.

The sound of the playback source is not heard.

•Input selector is not set properly.

➞Set to correct input source.

•Headphones are connected.

➞Lower volume and then disconnect headphones.

SPEAKERS

No sound from the center speaker, or at very low volume.

•Speaker cable is not connected.

➞Check the connection between the amplifier and the speaker.

•Listening mode is set to Stereo or Direct.

➞Set the Listening mode to any mode other than Stereo or Direct. The output to the center speaker may differ depending on the listening mode.

•Center speaker level is set to minimum.

➞Set the Center speaker level to the appropriate volume (page 22, 23, 27).

•The Center setting of the Speaker Config submenu is set to “None.”

➞Set the Center setting at the Speaker Config submenu to “Large” or “Small” (see pages 22, 23, 27).

No sound or very low volume from subwoofer.

•Subwoofer is set to “No.”

➞Check the speaker setting (pages 22, 23, 27).

•Subwoofer speakers output level setting is improper.

➞Check the output level of the Subwoofer using the test tone.

Low frequency humming is heard.

•Not properly grounded.

➞ Check outer conductor of input plugs.

•Turntable motor is not properly grounded.

➞Check for proper ground connection.

•Audio connection cables on the rear panel are connected incorrectly.

➞Adjust the placement of the cable to reduce hum.

Howling is heard when the volume is turned up.

•Turntable and speakers are located too close together. ➞ Move them farther apart.

Rough or scratchy sound is heard. High range is not clear.

•The needles of turntable is dirty or worn, or a problem exists with a connected component.

➞Refer to the instruction of the connected components and check for problem.

•Treble control is too high.

➞Turn treble down.

FM/AM TUNER

AM stations cannot be received.

•AM loop antenna is not connected.

➞Connect the included AM loop antenna to the AM antenna terminals.

Buzzing noise on AM stations (particularly noticeable at night or with weak stations).

•Noise from electrical apparatus such as fluorescent lamp.

➞Move the AM loop antenna to different position.

➞Set up an outdoor AM antenna.

Noise is heard at high-pitched sounds on AM stations.

•Noise from TV set.

➞Place the AM loop antenna as far as possible from the TV.

➞Move unit away from TV set.

Crackling noise on both AM and FM stations.

•Noise caused by fluorescent lamp being turned on and off.

➞Move antenna as far as possible from the fluorescent lamp.

•Noise from automobile ignition.

➞Install an FM outdoor antenna as far as possible from the road.

➞Change the position or direction of the outdoor antenna.

The indicators light for stereo reception, but sound is distorted and stereo separation is bad.

•Station is too strong.

➞Change to FM indoor antenna.

•Multiple reflection of the radio waves because of tall buildings or mountains.

➞Use antenna that has better directivity and select a point where distortion is least.

Indicators for stereo reception flicker and hiss is heard on FM stations.

•Station is too weak.

➞Install an outdoor FM antenna.

•Stereo FM broadcasts cover only about half the distance of an ordinary broadcast.

➞Change the position or direction of the outdoor antenna.

No preset station is recalled.

•Power cord has been unplugged or the POWER switch has been turned off for a long time.

➞ The memory contents are lost. Store all stations again.

62

Page 61 Page 63
Image 62
Page 61 Page 63
Contents TX-DS696 Important Safeguards AvisPrecautions Contents Contents Features Supplied accessoriesUsing the remote controller Before using this unitSetting the Voltage selector Worldwide models only Installing the remote controller batteriesFront panel display Front panel facilitiesFront panel Front panel facilities Remote controller Remote controller Improper connection Inserted completely Connecting power amplifiers Voltage selectorConnections Optical digital input terminalConnecting a compact disc player CD Connecting your audio componentsConnecting a turntable Phono ConnectionsConnecting a DVD player DVD Connecting your video componentsFlow of the video signals is as follows Audio connection cable Left White Video connection cableConnecting a television monitor or projector Connecting a video cassette recorder VideoConnecting a satellite tuner or television Video Connecting settop box or video camera, etc. VideoPower off function Connecting power amplifiersPower on/ready function Connect to devices with z terminalsStandard speaker placement Connecting speakersPositioning speakers Connecting speakers Check the impedance of the speakers you are connectingConnecting the remote zone speakers Connecting speakersConnecting the speaker cable Connecting a subwoofer 345Connecting the power Connecting the included antennas Connecting antennasConnecting the AM antenna cable Assembling the AM loop antennaConnecting an AM outdoor antenna Connecting antennasConnecting an FM outdoor antenna Directional linkagePress the Setup button Speaker setupSpeaker Configuration submenu Buttons to be usedSpeaker setup Speaker Distance submenuLevel Calibration submenu About the other settingsTurn the jog dial to adjust Press the jog dial againListening to Radio Broadcasts Tuning into a radio stationListening to a stereo radio station FM mode Erasing a preset radio station Presetting a radio stationSelecting a preset radio station Listening to Radio BroadcastsListening to RDS broadcasts What is RDS?Listening to RDS broadcasts European models only PTY program types in EuropePerforming a TP scan Listening to RDS broadcastsDisplaying Radio Text RT Performing a PTY scanEnjoying music or videos with the TX-DS696 Adjusting the bass and trebleListening with headphones Temporarily turning off the soundUsing the sleep time remote controller only Switching the displayAdjusting the brightness of the front display Enjoying music or videos with the TX-DS696Adjust the tone using the Bass and Treble dials Changing the audio modeUsing the tone control Enjoying the multichannel outputUsing listening mode Listening modesUsing Cinema Re-Equalization Using listening modeChanging the listening mode Listening Mode Buttons Re-EQMenu Setup menusMain menu Sub menuSetting procedures and button operations Setup menusNavigating through the Setup menu Speaker Setup menu TipLevel Calibration sub-menu Speaker Config sub-menuSpeaker Distance sub-menu Calibrating the speaker levelsSource Input Setup menuInput Digital Input Audio Setup sub-menuVideo Setup sub-menu MultichannelIntelliVolume Listening Mode Preset sub-menu IntelliVolume sub-menuInput source signals Analog/PCM SourceRelationship between listening mode and parameter Listening Mode Setup menuDescription listening mode parameters Front EffectLate Night Setup sub-menu Volume Setup sub-menuHeadphones Level sub-menu AM Freq Step Setup sub-menu Worldwide model onlyOSD Config sub-menu OSD Setup menuOSD Setup sub-menu OSD Position sub-menuRecording both the audio and video RecordingRecording the input source REC OUT selector Recording a source different from that you are listening toEnjoying music in the remote zone Overview Using remote controllerCalling up a preset radio station Controlling an Onkyo cassette tape deckDisc Stdby CD Mode Using remote controllerPress the CD Mode button Controlling an Onkyo CD playerControlling an Onkyo DVD player Press the DVD Mode buttonReturn DVD Mode Disc VOL TOP Menu Audio Muting Angle Subtitle DVDControlling an Onkyo MD recorder SAT, CABLE, VCR, and TV Mode buttonsPress the MD Mode button To 9, 0, --/--- Numeric keysLearning a pre-programming code SEND/LEARN indicator Buttons thatLearning a pre-programming code Within 30 seconds, enter the 3-digit code numberLearning a pre-programming code Pre-programmong codesSAT Mode Satellite Tuner Mode Operating your programmed remote controllerDVD Mode DVD Player Mode Cable Mode Cable Tuner ModeTV Mode TV Mode Operating your programmed remote controllerVCR Mode VCR Mode Press the VCR Mode buttonSEND/LEARN Programming procedureMode Direct Mode Macro LightPage Press and release the same Mode button again Erasing the programmed command from one buttonErasing all the commands programmed under a Mode button SEND/LEARN indicator Mode buttonsPress the Mode Macro button to complete the programming Using a Macro functionWhat is a Macro function? Programming a Macro functionRunning a Direct Macro function Using a Macro functionProgramming the Direct Macro function Direct Macro Mode buttons Erasing a macro from the Mode Macro buttonPress the Mode Macro button again Erasing a direct macro from the Direct Macro buttonPress the Enter button Erasing all commands and macros that have been programmedMacro mode programming memo OperationSpecifications Amplifier SectionTroubleshooting guide If one of the messages shown below appears Troubleshooting guideVideo and Audio Onkyo China Limited Onkyo U.S.A. CorporationOnkyo Europe Electronics GmbH

TX-DS696 specifications

The Onkyo TX-DS696 is a powerful and versatile home theater receiver that has left a significant mark in the world of audio and video entertainment. Launched to cater to audiophiles and home cinema enthusiasts, this receiver is known for its robust performance, extensive connectivity options, and user-friendly features, making it a popular choice among consumers.

At the heart of the TX-DS696 is its impressive multichannel processing capabilities. Supporting Dolby Digital and DTS surround sound formats, it delivers immersive audio experiences that enhance the enjoyment of movies, music, and games. The 5.1 channel configuration allows for exceptional sound staging, giving users a truly cinematic experience right in their living rooms.

One of the standout features of the TX-DS696 is its advanced room calibration technology. The receiver analyzes the acoustic characteristics of the room and adjusts the speaker settings accordingly, optimizing sound quality for any space. This ensures that listeners can enjoy a balanced audio performance regardless of their room’s layout or size.

Connection options are plentiful, with multiple audio and video inputs that facilitate direct connections to various devices. The receiver includes several composite and S-Video inputs, along with digital optical and coaxial inputs, allowing users to connect DVD players, gaming consoles, and other multimedia devices easily. The support for component video ensures high-quality image transfer, making it an excellent choice for those who want to enjoy high-definition video.

In terms of power, the TX-DS696 boasts a robust amplifier section capable of delivering rich and dynamic sound across all channels. The built-in high-current amplification technology ensures that even demanding speakers are driven effortlessly, resulting in clean and distortion-free audio at all volume levels.

The user interface is intuitive, with an easy-to-read LCD display and a well-laid-out remote control that provides convenient access to all the receiver’s functions. Additionally, the Onkyo TX-DS696 is compatible with various external devices, allowing for custom configurations that cater to personal preferences.

Overall, the Onkyo TX-DS696 stands out as an exemplary home theater receiver that combines advanced technology, user-friendly features, and powerful performance. Whether you’re a dedicated home theater enthusiast or a casual listener, this receiver offers a rich audio experience that is hard to match. Its blend of performance, versatility, and value makes it a lasting favorite in the realm of home audio systems.
Top Page Image Contents