Onkyo TX-DS696 appendix

Page 55

Programming the commands of remote controllers for other devices into the remote controller

4.Press and hold down the button (that corresponds to the command you are programming) on the remote controller of the other device until the SEND/LEARN lamp on the remote controller flashes twice.

After flashing twice, the SEND/LEARN indicator will light again.

5.Repeat Steps 3 and 4 to transfer all the commands you desire from the other remote controller and program them to buttons on the remote controller under the same MODE.

Repeat Steps 2 through 4 to program commands to a different MODE (e.g., when programming from a different remote controller).

6.Press the MODE button that you pressed in step 2 to complete the programming.

7.Operate the newly programmed buttons to make sure the learning function was performed properly.

Notes:

•The remote controller codes for Onkyo compact disc players, cassette tape decks, DVD players, and mini disc recorder have already been programmed into buttons on the remote controller. You may, however, use these buttons to program the codes for other remote controllers. If you wish to restore the Onkyo preset codes after you program new codes, you must first erase the new codes (see page 56).

•The remote controller has 408 memory slots (8 modes ⋅ 51 buttons). Some remote controllers may have more commands that can be remembered by the remote controller. In such cases, it will be necessary for you to determine which commands are more important than others.

•If no button is pressed for more than 30 seconds during the programming, or if you perform an invalid operation during programming, the SEND/LEARN indicator flashes three times quickly, and the remote controller exits the programming mode. Resume from Step 2.

•If a failure occurs during programming, the SEND/LEARN indicator flashes three times quickly, and the remote controller exits the programming mode. Resume from Step 3.

•If a failure occurs five times in row during programming, the remote controller exits the programming mode. Resume from Step 3.

•If you try to program beyond the learning capacity of the remote controller, the SEND/LEARN indicator flashes six times quickly, and the remote controller exits the programming mode. Try programming under a different MODE button.

•When you want to program a command to a button to which you have already programmed a command, simply follow the same procedure given and programming for that button will be overwritten.

•The remote controller uses infrared rays to send its commands, as do most other remote controllers. Though most remote controller codes can be memorized by the remote controller, be aware that some remote controllers use a system that is quite different from the remote controller and therefore may not be able to be programmed.

•Some remote controllers have a single button that performs multiple functions (for example, the function may change each time the button is pressed). If this is the case, each function must be programmed to a separate button on the remote controller.

•Once you have transferred the commands from the other remote controller, refer to the instruction manual that came with that product for instructions on how to operate that product.

•Make sure both the remote controller and the other remote controller have new batteries. If either of them has batteries that are low, you may not be able to program the commands of the other remote controller properly into the remote controller.

See page 56 for how to erase the memorized commands from all buttons.

55

Page 54 Page 56
Image 55
Page 54 Page 56
Contents TX-DS696 Avis Important SafeguardsPrecautions Contents Contents Supplied accessories FeaturesInstalling the remote controller batteries Before using this unitSetting the Voltage selector Worldwide models only Using the remote controllerFront panel Front panel facilitiesFront panel display Front panel facilities Remote controller Remote controller Optical digital input terminal Connecting power amplifiers Voltage selectorConnections Improper connection Inserted completelyConnections Connecting your audio componentsConnecting a turntable Phono Connecting a compact disc player CDAudio connection cable Left White Video connection cable Connecting your video componentsFlow of the video signals is as follows Connecting a DVD player DVDConnecting settop box or video camera, etc. Video Connecting a video cassette recorder VideoConnecting a satellite tuner or television Video Connecting a television monitor or projectorConnect to devices with z terminals Connecting power amplifiersPower on/ready function Power off functionCheck the impedance of the speakers you are connecting Connecting speakersPositioning speakers Connecting speakers Standard speaker placement345 Connecting speakersConnecting the speaker cable Connecting a subwoofer Connecting the remote zone speakersConnecting the power Assembling the AM loop antenna Connecting antennasConnecting the AM antenna cable Connecting the included antennasDirectional linkage Connecting antennasConnecting an FM outdoor antenna Connecting an AM outdoor antennaButtons to be used Speaker setupSpeaker Configuration submenu Press the Setup buttonSpeaker Distance submenu Speaker setupPress the jog dial again About the other settingsTurn the jog dial to adjust Level Calibration submenuListening to a stereo radio station FM mode Tuning into a radio stationListening to Radio Broadcasts Listening to Radio Broadcasts Presetting a radio stationSelecting a preset radio station Erasing a preset radio stationPTY program types in Europe What is RDS?Listening to RDS broadcasts European models only Listening to RDS broadcastsPerforming a PTY scan Listening to RDS broadcastsDisplaying Radio Text RT Performing a TP scanTemporarily turning off the sound Adjusting the bass and trebleListening with headphones Enjoying music or videos with the TX-DS696Enjoying music or videos with the TX-DS696 Switching the displayAdjusting the brightness of the front display Using the sleep time remote controller onlyEnjoying the multichannel output Changing the audio modeUsing the tone control Adjust the tone using the Bass and Treble dialsListening modes Using listening modeListening Mode Buttons Re-EQ Using listening modeChanging the listening mode Using Cinema Re-EqualizationSub menu Setup menusMain menu MenuNavigating through the Setup menu Setup menusSetting procedures and button operations Tip Speaker Setup menuCalibrating the speaker levels Speaker Config sub-menuSpeaker Distance sub-menu Level Calibration sub-menuInput Input Setup menuSource Multichannel Audio Setup sub-menuVideo Setup sub-menu Digital InputAnalog/PCM Source Listening Mode Preset sub-menu IntelliVolume sub-menuInput source signals IntelliVolumeFront Effect Listening Mode Setup menuDescription listening mode parameters Relationship between listening mode and parameterAM Freq Step Setup sub-menu Worldwide model only Volume Setup sub-menuHeadphones Level sub-menu Late Night Setup sub-menuOSD Position sub-menu OSD Setup menuOSD Setup sub-menu OSD Config sub-menuRecording a source different from that you are listening to RecordingRecording the input source REC OUT selector Recording both the audio and videoEnjoying music in the remote zone Controlling an Onkyo cassette tape deck Using remote controllerCalling up a preset radio station OverviewControlling an Onkyo CD player Using remote controllerPress the CD Mode button Disc Stdby CD ModeDisc VOL TOP Menu Audio Muting Angle Subtitle DVD Press the DVD Mode buttonReturn DVD Mode Controlling an Onkyo DVD playerTo 9, 0, --/--- Numeric keys SAT, CABLE, VCR, and TV Mode buttonsPress the MD Mode button Controlling an Onkyo MD recorderWithin 30 seconds, enter the 3-digit code number SEND/LEARN indicator Buttons thatLearning a pre-programming code Learning a pre-programming codePre-programmong codes Learning a pre-programming codeCable Mode Cable Tuner Mode Operating your programmed remote controllerDVD Mode DVD Player Mode SAT Mode Satellite Tuner ModePress the VCR Mode button Operating your programmed remote controllerVCR Mode VCR Mode TV Mode TV ModeLight Programming procedureMode Direct Mode Macro SEND/LEARNPage SEND/LEARN indicator Mode buttons Erasing the programmed command from one buttonErasing all the commands programmed under a Mode button Press and release the same Mode button againProgramming a Macro function Using a Macro functionWhat is a Macro function? Press the Mode Macro button to complete the programmingProgramming the Direct Macro function Using a Macro functionRunning a Direct Macro function Erasing a direct macro from the Direct Macro button Erasing a macro from the Mode Macro buttonPress the Mode Macro button again Direct Macro Mode buttonsOperation Erasing all commands and macros that have been programmedMacro mode programming memo Press the Enter buttonAmplifier Section SpecificationsTroubleshooting guide Video and Audio Troubleshooting guideIf one of the messages shown below appears Onkyo Europe Electronics GmbH Onkyo U.S.A. CorporationOnkyo China Limited

TX-DS696 specifications

The Onkyo TX-DS696 is a powerful and versatile home theater receiver that has left a significant mark in the world of audio and video entertainment. Launched to cater to audiophiles and home cinema enthusiasts, this receiver is known for its robust performance, extensive connectivity options, and user-friendly features, making it a popular choice among consumers.

At the heart of the TX-DS696 is its impressive multichannel processing capabilities. Supporting Dolby Digital and DTS surround sound formats, it delivers immersive audio experiences that enhance the enjoyment of movies, music, and games. The 5.1 channel configuration allows for exceptional sound staging, giving users a truly cinematic experience right in their living rooms.

One of the standout features of the TX-DS696 is its advanced room calibration technology. The receiver analyzes the acoustic characteristics of the room and adjusts the speaker settings accordingly, optimizing sound quality for any space. This ensures that listeners can enjoy a balanced audio performance regardless of their room’s layout or size.

Connection options are plentiful, with multiple audio and video inputs that facilitate direct connections to various devices. The receiver includes several composite and S-Video inputs, along with digital optical and coaxial inputs, allowing users to connect DVD players, gaming consoles, and other multimedia devices easily. The support for component video ensures high-quality image transfer, making it an excellent choice for those who want to enjoy high-definition video.

In terms of power, the TX-DS696 boasts a robust amplifier section capable of delivering rich and dynamic sound across all channels. The built-in high-current amplification technology ensures that even demanding speakers are driven effortlessly, resulting in clean and distortion-free audio at all volume levels.

The user interface is intuitive, with an easy-to-read LCD display and a well-laid-out remote control that provides convenient access to all the receiver’s functions. Additionally, the Onkyo TX-DS696 is compatible with various external devices, allowing for custom configurations that cater to personal preferences.

Overall, the Onkyo TX-DS696 stands out as an exemplary home theater receiver that combines advanced technology, user-friendly features, and powerful performance. Whether you’re a dedicated home theater enthusiast or a casual listener, this receiver offers a rich audio experience that is hard to match. Its blend of performance, versatility, and value makes it a lasting favorite in the realm of home audio systems.
Top Page Image Contents