Sharp X2 manual Replacing the waste ink bottle con’t, When to replace the waste ink bottle

Page 43

Replacing the waste ink bottle (con’t)

*WASTE BOTTLE FULL /NOT INSTALLED

SEE USER GUIDE [ER: 4621]

Procedures

When to replace the waste ink bottle

The waste ink bottle should be replaced when the waste ink bottle is filled with the waste ink.

For cases where the waste ink bottle is full, the LCD will display the Waste Bottle Full message.

The amount of waste ink in the waste ink bottle is measured by the waste ink bottle’s weight. The waste ink bottle tray acts as a scale and must move freely to properly measure the amount of waste ink in the bottle and prevent waste ink over-flow.

Caution: If the printer continues to run without detecting the change in the waste ink bottle’s weight, the waste ink bottle could overflow and contaminate the printer and floor.

Replacement procedures

The steps to replace waste ink bottle are:

1.Locate the waste ink bottle on the right rear side of the printer.

2.Pick up the waste ink bottle and tilt it to remove the bottle from the waste ink bottle tray.

3.Place the waste ink bottle into the disposable plastic bag.

3. Properly dispose of the used waste ink bottle.

4.Set the new waste ink bottle on the waste ink bottle tray. Ensure that the bottle is properly seated on the tray before continuing.

Supplies

31

Image 43

Contents X2 TECH, X2 Graphic Printer User Guide Page Introduction IntroductionConventions About this guide con’tIntroduction Iii OrganizationSupplies ServiceEME Compliance in Canada FCC Compliance in the USAConformité EEM Canada USAIntroduction Vii Maintenance safetyViii Introduction Maintenance safety con’tIntroduction Introduction Getting to Know Your ColorgrafX Feature overviewGetting to know your ColorgrafX High-speed / high quality printingQuick drying Ink Feature overview con’tMedia types Media widthsMinimum down-time Front view Printer componentsRight-side view Rear view Printer Components con’tPrinter components con’t Media transport Printer components con’t Media transport con’t Operation panel Ready Menuî Printer components con’t Operations panel con’tPrinter components con’t Operations Entering menu modeOperations panel menu Menu options Operations panel menu con’tTake Up Roller Set modeRoll Select Menu options con’t Set mode con’tMedia Type Media Menu options con’tAttribute Magnification Cut ModeWait Carriage Wait CutDate & Time Power SaveMaintenance IntervalOption Description Parameters Correction Rewind DelayAuto Cap FeedLife Counter 1 Replacing BladeStarting a print job Operating the cutter Replacing cutter blade Operating the cutter con’tReplacing cutter blade con’t Setup the take-up assembly Using the take-up rollerStarting the take-up roller Using the take-up roller con’tSetup the take-up assembly con’t Operating the printer from RIP softwareReplacing ink bottles PrecautionsWhen to replace ink bottle SuppliesReplacing ink bottles con’t Replacement proceduresSupplies Replacing the waste ink bottle Replacing the waste ink bottle con’t When to replace the waste ink bottleSupported media Loading and removing mediaLoading media in the printer Loading media in the printer con’t Loading and removing media con’tFeed roller knob Removing media When to replace mediaInk bottle storage Supply storageMedia storage Supply storage con’tMaintaining print quality Overview Head MaintenanceNormal maintenance Manual maintenance processTest Print Head Maintenance con’tMaintaining Print Quality Overview Jam clearance Clearing a media jamJam clearance Clearing a media jam con’tClearing a media jam con’t More tips for clearing media jams Clearing a cutter jam Jam clearance Printer doesnt turn on Trouble isolation proceduresCase of difficulty Overview Quick checksPrinter test Trouble isolation procedures con’tAdjustment auto mode Poor image qualityMAG. Multi Adjustment auto mode con’tBI-DIR Density Control panel menu item Magnification adjustment modeComputer interface test Computer interface test con’t Common operating problemsPoor image quality con’t Common operating problems con’tSymptom Potential Problem Suggested Solution Appendix a In Case of Difficulty Error Message LCD error messagesUser resolvable Manually Appendix B Menu Tree Menu TreeSET menu first level only Options SET menu detailedNone YES SET menu detailed con’tTest Print menu ADJUSTMENT, Auto menu Head Maintenance menuLife Counter menu Replacing Blade menu