Sharp X2 manual Starting a print job

Page 34

Starting a print job

To successfully start a print job, perform the following:

IMPORTANT!

READY

MENUÎ

 

R: 360 PRES 36

ggg Î

 

F: 720 PRES 54

ggg Î

 

 

 

 

 

 

 

<MENU>

S

 

 

SET Î

 

<MORE>

 

 

 

 

 

 

 

 

<SET>

S

 

MEDIA TYPE, REAR Î

MEDIA TYPE, FRONT Î

<MORE>

1.Visually check that the printer has adequate media available and that the ink bottles have enough ink to complete the print.

You must turn the printer on before the digital front end. This allows the computer to recognize the printer as a SCSI device.

2.When starting the printer, use the printer’s power switch to turn the printer ON. The printer will go through an internal self-check and media initialization to verify that it is ready to print. You will hear the printer’s motors operate as each printer component is verified and the media is initialized.

3.Check the printer’s operation panel LCD to verify that it is online and that there are no error messages displayed.

4.Verify at the operations panel that the appropriate media types are set. Refer to the default display. This information MUST match the installed media. If this is not the case, set the media type for both the front and rear rollers. The procedures are as follows:

a.To set the media type for the rear roller, press the MENU button, the SET button, and then use the arrow button to scroll to MEDIA TYPE, REAR.

b.Press the button associated with either the + or – until the media type installed on the rear roller is displayed and then press the ENTER button. This will return you to the SET menu.

c.To set the media type for the front roller, use the arrow button to scroll to MEDIA TYPE, FRONT.

d.Press the button associated with either the + or – until the media type installed on the front roller is displayed and then press the ENTER button.

5.Verify that the printer software in the host computer is operating, and verify that the interface between the host computer and the printer is working (no error messages on the host computer).

6.Using a print file in a format that your printer software can process, make any needed modifications to the print. After verifying that there is a roll of media on the printer of the type and width you need, send the print to the printer.

Note: Do not open any of the printer’s covers while the printer is operating. If a cover is opened, the printer immediately stops printing. The job in progress will be terminated when the cover is closed again.

22

Operations

Page 33 Page 35
Image 34
Page 33 Page 35
Contents X2 TECH, X2 Graphic Printer User Guide Page Introduction IntroductionAbout this guide con’t ConventionsOrganization Introduction IiiService SuppliesEME Compliance in Canada FCC Compliance in the USAConformité EEM USA CanadaMaintenance safety Introduction ViiMaintenance safety con’t Viii IntroductionIntroduction Introduction High-speed / high quality printing Feature overviewGetting to know your ColorgrafX Getting to Know Your ColorgrafXFeature overview con’t Quick drying InkMedia widths Media typesMinimum down-time Front view Printer componentsRight-side view Printer Components con’t Rear viewPrinter components con’t Media transport Printer components con’t Media transport con’t Operation panel Printer components con’t Operations panel con’t Ready MenuîPrinter components con’t Operations Entering menu modeOperations panel menu Operations panel menu con’t Menu optionsSet mode Take Up RollerRoll Select Menu options con’t Set mode con’tMedia Type Media Menu options con’tAttribute Wait Cut Cut ModeWait Carriage MagnificationInterval Power SaveMaintenance Date & TimeOption Description Parameters Feed Rewind DelayAuto Cap CorrectionReplacing Blade Life Counter 1Starting a print job Operating the cutter Operating the cutter con’t Replacing cutter bladeReplacing cutter blade con’t Using the take-up roller Setup the take-up assemblyOperating the printer from RIP software Using the take-up roller con’tSetup the take-up assembly con’t Starting the take-up rollerSupplies PrecautionsWhen to replace ink bottle Replacing ink bottlesReplacing ink bottles con’t Replacement proceduresSupplies Replacing the waste ink bottle When to replace the waste ink bottle Replacing the waste ink bottle con’tSupported media Loading and removing mediaLoading media in the printer Loading and removing media con’t Loading media in the printer con’tFeed roller knob When to replace media Removing mediaSupply storage Ink bottle storageSupply storage con’t Media storageManual maintenance process Head MaintenanceNormal maintenance Maintaining print quality OverviewTest Print Head Maintenance con’tMaintaining Print Quality Jam clearance Clearing a media jam OverviewClearing a media jam con’t Jam clearanceClearing a media jam con’t More tips for clearing media jams Clearing a cutter jam Jam clearance Quick checks Trouble isolation proceduresCase of difficulty Overview Printer doesnt turn onPoor image quality Trouble isolation procedures con’tAdjustment auto mode Printer testAdjustment auto mode con’t MAG. MultiBI-DIR Density Control panel menu item Magnification adjustment modeComputer interface test Common operating problems Computer interface test con’tCommon operating problems con’t Poor image quality con’tSymptom Potential Problem Suggested Solution Appendix a In Case of Difficulty Error Message LCD error messagesUser resolvable Manually Menu Tree Appendix B Menu TreeSET menu first level only SET menu detailed OptionsSET menu detailed con’t None YESTest Print menu Head Maintenance menu ADJUSTMENT, Auto menuReplacing Blade menu Life Counter menu
Top Page Image Contents