Sharp X2 manual Feed roller knob

Page 46

Loading and removing media (con’t)

Loading media in the printer (con’t)

Feed roller knob

11.Rotate the feed roller knob toward you. Continue to forward the media until you hear a beep from the printer. The printer will sense the new media’s leading edge. Ensure that there is even tension and no wrinkles on the media.

12.Close the printer’s top cover. The printer will start initializing, and you should hear activity as it checks and positions the newly loaded media roll.

After completing its self-test, the printer will forward some of the newly loaded media through the print path and then cut it. This assures that the media has a clean-cut leading edge when printing.

13.Examine the cut edge of the media to verify that the cutter is properly set and is cutting the media cleanly. If it is not a clean cut, change the printer’s cutter setting to match the media type. Refer to the Operations chapter as described in Media type.

14.Ensure the printer is online and ready to receive the next print job.

15.Set the media type and attributes at the operations panel. Refer to the Operations Panel Menu section.

This completes installation of a new media roll in the printer.

Feed roller knob

34

Supplies

Image 46
Contents X2 TECH, X2 Graphic Printer User Guide Page Introduction IntroductionAbout this guide con’t ConventionsOrganization Introduction IiiService SuppliesEME Compliance in Canada FCC Compliance in the USAConformité EEM USA CanadaMaintenance safety Introduction ViiMaintenance safety con’t Viii IntroductionIntroduction Introduction High-speed / high quality printing Feature overviewGetting to know your ColorgrafX Getting to Know Your ColorgrafXFeature overview con’t Quick drying InkMedia widths Media typesMinimum down-time Front view Printer componentsRight-side view Printer Components con’t Rear viewPrinter components con’t Media transport Printer components con’t Media transport con’t Operation panel Printer components con’t Operations panel con’t Ready MenuîPrinter components con’t Operations Entering menu modeOperations panel menu Operations panel menu con’t Menu optionsSet mode Take Up RollerRoll Select Menu options con’t Set mode con’tMedia Type Media Menu options con’tAttribute Wait Cut Cut ModeWait Carriage MagnificationInterval Power SaveMaintenance Date & TimeOption Description Parameters Feed Rewind DelayAuto Cap CorrectionReplacing Blade Life Counter 1Starting a print job Operating the cutter Operating the cutter con’t Replacing cutter bladeReplacing cutter blade con’t Using the take-up roller Setup the take-up assemblyOperating the printer from RIP software Using the take-up roller con’tSetup the take-up assembly con’t Starting the take-up rollerSupplies PrecautionsWhen to replace ink bottle Replacing ink bottlesReplacing ink bottles con’t Replacement proceduresSupplies Replacing the waste ink bottle When to replace the waste ink bottle Replacing the waste ink bottle con’tSupported media Loading and removing mediaLoading media in the printer Loading and removing media con’t Loading media in the printer con’tFeed roller knob When to replace media Removing mediaSupply storage Ink bottle storageSupply storage con’t Media storageManual maintenance process Head MaintenanceNormal maintenance Maintaining print quality OverviewTest Print Head Maintenance con’tMaintaining Print Quality Jam clearance Clearing a media jam OverviewClearing a media jam con’t Jam clearanceClearing a media jam con’t More tips for clearing media jams Clearing a cutter jam Jam clearance Quick checks Trouble isolation proceduresCase of difficulty Overview Printer doesnt turn onPoor image quality Trouble isolation procedures con’tAdjustment auto mode Printer testAdjustment auto mode con’t MAG. MultiBI-DIR Density Control panel menu item Magnification adjustment modeComputer interface test Common operating problems Computer interface test con’tCommon operating problems con’t Poor image quality con’tSymptom Potential Problem Suggested Solution Appendix a In Case of Difficulty Error Message LCD error messagesUser resolvable Manually Menu Tree Appendix B Menu TreeSET menu first level only SET menu detailed OptionsSET menu detailed con’t None YESTest Print menu Head Maintenance menu ADJUSTMENT, Auto menuReplacing Blade menu Life Counter menu