Vidikron VP-60, VP-42HD, VP-50 » Aspect Ratio Operation with Computer Signals, Within 3 seconds

Page 28

» Aspect Ratio Operation with Computer Signals

Switch to the wide screen mode to expand the 4:3 image to fill the entire screen.

1.Press the ASPECT button on the remote control.

2.Within 3 seconds...

Press the ASPECT button again. The screen size switches as follows:

STD (4:3) ANAMPHC LTR BOX

STD 4:3 mode (4:3 or SXGA 5:4)

Active

Image

Area

The picture has the same size as the normal computer image.

ANAMPHC mode

Active Image Area

The image is expanded in the horizontal direction.

Aspect Ratio Controls

LTR BOX mode

Active Image Area

When wide signals are input.

Information

■Supported resolution

See page 106 for details on the display output of the various VESA signal standards supported by the monitor.

■When 853 (848) dot x 480 line wide VGA *signals with a vertical frequency of 60 Hz and horizontal frequency of 31.7 (31.0) kHz are input.

Select an appropriate setting for RGB SELECT mode referring to the “Table of Signals Supported” on page 106.

* “IBM PC/AT” and “VGA” are registered trademarks of IBM, Inc. of the United States.

NOTE:

Do not leave the displayed in 4:3 mode for an extended period. This can cause a phosphor burn-in.

27

Image 28

Contents Page Table of Contents Introduction Contents of the package » The features you’ll enjoy includeOptions » Precautions Important Information» Warnings and Safety Precautions Important Information» To avoid damage and prolong operating life » Plasma monitor cleaning procedure Limited Warranty What is Covered Under the Terms of this Limited WarrantyEffective Warranty Date Limited WarrantyImportant Warranty Registration RIGHTS, Limits and ExclusionsAdditional Information VidikronHOW to Attach Options to the Plasma Monitor Ventilation Requirements for enclosure mountingPart Names and Functions » Front ViewAUDIO1, AUDIO2, AUDIO3 » Rear View / Terminal BoardExternal Control Rear View / Terminal Board Y Cb/Pb» Remote Control Remote Control Displays the source settings on the screenDisplay Light» Battery Installation and Replacement » Handling the remote control » Operating RangeInstallation VideoInstallation » Connecting Your PC or Macintosh Computer» Connecting Your VCR or Laser Disc Player » Connecting Your DVD Player» Pin Assignment and Signal Levels for 15 pin RGB analog RGB» Power » VolumeBasic Operations » Mute» Timer OFF To set the timer offTo cancel the off timer Basic OperationsAspect Ratio Controls » Aspect Ratio Operations ManualIntelliwide mode Aspect Ratio Controls» Aspect Ratio Operation with Computer Signals Within 3 secondsChange the adjustments or the settings that are stored Button on the remote control to return to the main menuOSD On Screen Display Controls » Menu Operations Memory. The change is stored until you change it againAdjust OSD On Screen Display ControlsImage HD Type Language Adjusting the picture » Picture Adjust MenuUse the and buttons to adjust the contrast Example Setting the Factory mode Once the adjustment is completedTo set to Factory Types of picture modes LW BLK1Reducing noise in the picture Once the setting is completedTypes of noise reduction See below to set White Balance Adjust Setting the White BalanceAdjusting the color to the desired level Adjusting the white balance Adjust the white balance using the and buttonsChanging the Gamma Curve Making the Dither adjustments Gamma Curve settingsDither settings Adjusting the colorsDiffuse » Audio Setup Menu To continue adjusting the audioColor Chart settings Audio setup menuExample Setting Audio INPUT1 to Video Setting the allocation of the audio connectorsTo set the Audio INPUT1 to VIDEO2 » Image Options Settings Menu To select a modeTo adjust the vertical position To continue making other computer image adjustmentsAdjusting the Computer Adjusting the position of the imageRestoring the factory defaults settings OFFSetting the on-screen menu » Setting 1 Settings MenuTo set the Display OSD to OFF Setting the BNC connectors To set the BNC Input mode to CompOSD Orbiter settings BNC Input settingsIt is set to RGB and can not be adjusted Example Setting the RGB Type mode to AutoTo set the RGB select mode to Auto RGB Type modesExample Setting the 1080B mode to To set the HD Type mode to 1080BSetting the Input Skip To set the Input Skip mode to OFFInput Skip settings HD Type modesResetting to the default values Use the and buttons to select ON, then press the Menu buttonSetting the Auto Off for computer images » Setting 2 MenuTo turn the Auto Off function on Power / Standby indicator Setting the picture to suit the moviePerform Steps 1-2 of Pixl PROTECT, then Orbiter settings OrbiterAdjust the Orbiter function manually Orbiter Function settingsPerform Steps 1-3 of ORBITER, then InverseSetting the time for INVERSE/WHITE Setting the timePerform Steps 1-3 of INVERSE, then Press the Exit button to return to the Pixl Protect screenImage Sweep Example Setting Image Sweep to onPerform Steps 1-3 of Image SWEEP, then Setting the Sidebar Lev. for the sides of the screen Soften settingsPress the Exit button to return to the Image Sweep screen SoftenTo adjust the Sidebar LEV Use the and buttons to adjust the Sidebar LEVSetting the screen size for S1/S2 video input Sidebar LEV. settingsS1/S2 Settings PLUG/PLAY SettingsBlack Level settings Perform the following operations» Setting 3 Menu Using the timerPreset Time Perform Steps 1-2 of TIMER, thenPreset Time settings Daylight Saving TimeDAY HourUse the and buttons to select Program Program TimerON/OFF Hour To set the Default Input to VIDEO2 Setting the Default InputUse the and buttons to select VIDEO2 Input Select settings → RGB3 ↔ RGB2 ↔ RGB1 ↔ HD1 ←→ RGB3 ↔ RGB1 ↔ HD2 ↔ HD1 ← Enabling/disabling the front panel controlsExample Setting OFF Perform the following operations To set the IR Enable to OFFControl Lock settings To set the Control Lock to onLoop Out Setting IR Enable settingsLoop OUT settings To set the Loop OUT to onID Number Setting To reset back to ALL Press the Clear buttonID Number settings When the ID Number has been setVideo Wall Setting Use this feature to configure a 2×2 or 3×3 video wallSet the 2x2 or 3x3 video wall Example Setting Set the position of each display Example SettingDivider Perform Steps 1-2 of Video WALL, thenDISP. Mode Video Wall Position settingsPress the Exit button to return to the Video Wall screen Auto IDAuto ID settings UseOn Delay Power on delay On Delay settings Video WallLUM SET Link settings Repeat Timer ReptrUse the and buttons to select Reptr Time Reptr Time settings Divider Source» Language Settings Menu Setting the language for the menusLanguage settings English German French Spanish Italian To select Deutsch» Video Standard Menu Setting the video signal formatTo select 3.58NTSC Once you have checked the frequency » Signal Info. MenuVideo standard formats External Controls ApplicationConnections Communication ParametersCommand Communication FormatExternal Controls Unit ID 1 and Unit IDCommand Reference List CMD1 CMD2 LENPower OFF Power onInput Switch Change Volume Gain Data Audio Mute onAudio Mute OFF Contrast Gain DataBright Gain Data Sharpness Gain DataColor Gain Data Tint Gain DataImage MEM. Select White BAL. SelectRED Gain Data Green Gain DataVID NR Mode SET Blue Gain DataBass Gain Data Treble Gain DataBalance Gain Data Aspect Ratio SelectShift Gain Data Size Gain Data Phase Gain Data Clock Gain DataOSD Select OSD ADJ. Gain DataAuto OFF Select Cinema Mode SETSidebar LEV. SET 33 RGB3 ADJ. Select Pixl Protect SETInverse SET Image Sweep SETFactory Audio Select SETBNC Select RGB SelectLanguage Select HD Select100 Frequency Request Video Standard Select101 Input Mode Request 102Video ADJ Request 103Auto Select Request 104Model Name Request Failure Mode Request105 Computer input signals supported by this system Table of Signals Supported106 Table of Signals Supported 107PAL625P Troubleshooting 109Troubleshooting 110Specifications 111Specifications 112Dimensions 113Dimensions 114VP-60 115RUMA-010550