Vidikron VP-42, VP-60, VP-50 Use the and buttons to select Sidebar LEV, To adjust the Sidebar LEV

Page 59

OSD (On Screen Display) Controls

2.Use the and buttons to select “SIDEBAR LEV.”.

3.To adjust the “SIDEBAR LEV.” ...

Use the and buttons to adjust the SIDEBAR LEV..

		SETTING 2				2 / 3
		PREVIOUS PG.
	AUTO OFF			:	OFF
	CINEMA MODE			:	ON
	PIXL PROTECT			:	OFF

	SIDEBAR LEV.			:	5
	S1 / S2			:	OFF
	DVI TYPE
		NEXT PAGE
	SEL.	ADJ.			EXIT EXIT

Information

■SIDEBAR LEV. settings

This adjusts the brightness of the black (the Sidebar Lev.) for the sides of the screen. The standard is 0 (black). The level can be adjusted from 0 to 15. The factory setting is 3 (dark gray).

■Restoring the factory default settings

Select “FACTORY” under the SETTING 1 menu.

Note that this also restores other settings to the factory defaults.

Setting the screen size for S1/S2 video input

If the S-Video signal contains screen size information, the image will be automatically adjusted to fit the screen when this S1/S2 is set to AUTO.

This feature is available only when an S-Video signal is input via the VIDEO3 terminal.

Example: Setting the “S1/S2” to “AUTO” Perform the following operations.

1.On the MAIN MENU, select “SETTING 2”, then press MENU button. The “SETTING 2” screen appears.

2.Use the and buttons to select “S1/S2”.

3.Use the and buttons to select “AUTO”. The mode switches as follows each time the and buttons is pressed:

OFF AUTO

		SETTING 2				2 / 3
	PREVIOUS PG.
	PWR. MGT.			:	OFF
	CINEMA MODE			:	ON
	PIXL PROTECT			:	OFF
	SIDE BARS			:	5

	S1 / S2			:	AUTO
	AUTO SIZE			:	ON
	DVI TYPE
	NEXT PAGE
	SEL.	ADJ.			EXIT EXIT

58

Image 59

Contents Page Table of Contents Introduction Options » The features you’ll enjoy includeContents of the package Important Information » PrecautionsImportant Information » Warnings and Safety Precautions» To avoid damage and prolong operating life » Plasma monitor cleaning procedure What is Covered Under the Terms of this Limited Warranty Limited WarrantyRIGHTS, Limits and Exclusions Effective Warranty DateLimited Warranty Important Warranty RegistrationVidikron Additional InformationVentilation Requirements for enclosure mounting HOW to Attach Options to the Plasma Monitor» Front View Part Names and FunctionsExternal Control » Rear View / Terminal BoardAUDIO1, AUDIO2, AUDIO3 Y Cb/Pb Rear View / Terminal Board» Remote Control Light Remote ControlDisplays the source settings on the screen Display» Battery Installation and Replacement » Operating Range » Handling the remote controlVideo Installation» Connecting Your PC or Macintosh Computer Installation» Connecting Your DVD Player » Connecting Your VCR or Laser Disc PlayerRGB » Pin Assignment and Signal Levels for 15 pin RGB analog» Mute » Power» Volume Basic OperationsBasic Operations » Timer OFFTo set the timer off To cancel the off timer» Aspect Ratio Operations Manual Aspect Ratio ControlsAspect Ratio Controls Intelliwide modeWithin 3 seconds » Aspect Ratio Operation with Computer SignalsMemory. The change is stored until you change it again Change the adjustments or the settings that are storedButton on the remote control to return to the main menu OSD On Screen Display Controls » Menu OperationsOSD On Screen Display Controls AdjustImage HD Type Language Use the and buttons to adjust the contrast » Picture Adjust MenuAdjusting the picture Types of picture modes LW BLK1 Example Setting the Factory modeOnce the adjustment is completed To set to FactoryTypes of noise reduction Once the setting is completedReducing noise in the picture Adjusting the color to the desired level Setting the White BalanceSee below to set White Balance Adjust Changing the Gamma Curve Adjust the white balance using the and buttonsAdjusting the white balance Gamma Curve settings Making the Dither adjustmentsDiffuse Adjusting the colorsDither settings Audio setup menu » Audio Setup MenuTo continue adjusting the audio Color Chart settingsTo set the Audio INPUT1 to VIDEO2 Setting the allocation of the audio connectorsExample Setting Audio INPUT1 to Video To continue making other computer image adjustments » Image Options Settings MenuTo select a mode To adjust the vertical positionOFF Adjusting the ComputerAdjusting the position of the image Restoring the factory defaults settingsTo set the Display OSD to OFF » Setting 1 Settings MenuSetting the on-screen menu BNC Input settings Setting the BNC connectorsTo set the BNC Input mode to Comp OSD Orbiter settingsRGB Type modes It is set to RGB and can not be adjustedExample Setting the RGB Type mode to Auto To set the RGB select mode to AutoTo set the HD Type mode to 1080B Example Setting the 1080B mode toHD Type modes Setting the Input SkipTo set the Input Skip mode to OFF Input Skip settingsUse the and buttons to select ON, then press the Menu button Resetting to the default valuesTo turn the Auto Off function on » Setting 2 MenuSetting the Auto Off for computer images Setting the picture to suit the movie Power / Standby indicatorPerform Steps 1-2 of Pixl PROTECT, then Orbiter Orbiter settingsInverse Adjust the Orbiter function manuallyOrbiter Function settings Perform Steps 1-3 of ORBITER, thenPress the Exit button to return to the Pixl Protect screen Setting the time for INVERSE/WHITESetting the time Perform Steps 1-3 of INVERSE, thenPerform Steps 1-3 of Image SWEEP, then Example Setting Image Sweep to onImage Sweep Soften Setting the Sidebar Lev. for the sides of the screenSoften settings Press the Exit button to return to the Image Sweep screenSidebar LEV. settings To adjust the Sidebar LEVUse the and buttons to adjust the Sidebar LEV Setting the screen size for S1/S2 video inputPerform the following operations S1/S2 SettingsPLUG/PLAY Settings Black Level settingsPerform Steps 1-2 of TIMER, then » Setting 3 MenuUsing the timer Preset TimeHour Preset Time settingsDaylight Saving Time DAYON/OFF Hour Program TimerUse the and buttons to select Program Use the and buttons to select VIDEO2 Setting the Default InputTo set the Default Input to VIDEO2 Enabling/disabling the front panel controls Input Select settings→ RGB3 ↔ RGB2 ↔ RGB1 ↔ HD1 ← → RGB3 ↔ RGB1 ↔ HD2 ↔ HD1 ←To set the Control Lock to on Example Setting OFF Perform the following operationsTo set the IR Enable to OFF Control Lock settingsTo set the Loop OUT to on Loop Out SettingIR Enable settings Loop OUT settingsWhen the ID Number has been set ID Number SettingTo reset back to ALL Press the Clear button ID Number settingsUse this feature to configure a 2×2 or 3×3 video wall Video Wall SettingPerform Steps 1-2 of Video WALL, then Set the 2x2 or 3x3 video wall Example SettingSet the position of each display Example Setting DividerAuto ID DISP. ModeVideo Wall Position settings Press the Exit button to return to the Video Wall screenUse Auto ID settingsOn Delay Power on delay Video Wall On Delay settingsUse the and buttons to select Reptr Time Repeat Timer ReptrLUM SET Link settings Divider Source Reptr Time settingsTo select Deutsch » Language Settings MenuSetting the language for the menus Language settings English German French Spanish ItalianTo select 3.58NTSC Setting the video signal format» Video Standard Menu Video standard formats » Signal Info. MenuOnce you have checked the frequency Communication Parameters External ControlsApplication ConnectionsUnit ID 1 and Unit ID CommandCommunication Format External ControlsCMD1 CMD2 LEN Command Reference ListInput Switch Change Power onPower OFF Contrast Gain Data Volume Gain DataAudio Mute on Audio Mute OFFSharpness Gain Data Bright Gain DataTint Gain Data Color Gain DataWhite BAL. Select Image MEM. SelectGreen Gain Data RED Gain DataBlue Gain Data VID NR Mode SETTreble Gain Data Bass Gain DataAspect Ratio Select Balance Gain DataShift Gain Data Size Gain Data Clock Gain Data Phase Gain DataOSD ADJ. Gain Data OSD SelectSidebar LEV. SET Cinema Mode SETAuto OFF Select Pixl Protect SET 33 RGB3 ADJ. SelectImage Sweep SET Inverse SETAudio Select SET FactoryRGB Select BNC Select100 HD SelectLanguage Select 101 Video Standard SelectFrequency Request 102 Input Mode Request103 Video ADJ Request104 Auto Select Request105 Failure Mode RequestModel Name Request 106 Table of Signals SupportedComputer input signals supported by this system 107 Table of Signals SupportedPAL625P 109 Troubleshooting110 Troubleshooting111 Specifications112 Specifications113 Dimensions114 Dimensions115 VP-60RUMA-010550