Sharp XG-V10XU operation manual Lamp/Maintenance Indicators

Page 70

Lamp/Maintenance Indicators

Maintenance Indicators

TEMP LAMP2 LAMP1 POWER

2

1

TEMPERATURE

LAMP 2

LAMP 1

POWER

WARNING

REPLACEMENT

REPLACEMENT

indicator

indicator

indicator

indicator

 

•The warning lights on the projector indicate problems inside the projector.

•There are three warning lights: a TEMPERATURE WARNING indicator that warns you when the projector is too hot, and two LAMP REPLACEMENT indicators that warn you when to change a lamp.

•If a problem occurs, either the TEMPERATURE WARNING indicator or the LAMP REPLACEMENT indicators will light up red. After turning off the power, follow the procedures given below.

&Troubleshooting

Maintenance

Maintenance Indicator

Condition

Problem

Possible Solution

TEMPERATURE

The internal

• Blocked air intake.

• Relocate the projector to an area with

WARNING indicator

temperature is

 

proper ventilation.

 

abnormally high.

• Clogged air filter.

• Replace the filter.

 

 

 

(See page 73.)

 

 

• Cooling fan breakdown.

• Take the projector to your nearest

 

 

• Internal circuit failure.

Authorized Sharp Industrial LCD Products

 

 

 

Dealer or Service Center for repair.

LAMP REPLACE-

The lamp does not

• Burnt-out lamp.

• Carefully replace the lamp. (See pages 71

MENT indicator

light up.

• Lamp circuit failure.

and 72.)

 

 

 

• Take the projector to your nearest

 

The lamp requires

• Lamp has been used for

Authorized Sharp Industrial LCD Products

 

replacement.

over 900 hours.

Dealer or Service Center for repair.

POWER indicator

The POWER

• The filter cover is open.

• Securely install the filter cover.

 

indicator flashes in

• The lens cover* is not

• Securely install the lens cover.

 

red when the

 

securely installed.

 

 

projector is on.

 

 

 

 

* The lens cover is as shown below.

 

 

 

Lens cover

 

 

•If the TEMPERATURE WARNING indicator lights up, follow the above possible solutions and then wait until the projector has cooled down completely before turning the power back on. (At least 5 minutes.)

•If the power is turned off and then turned on again, as during a brief rest, the LAMP REPLACEMENT indicators may be triggered, preventing the power from going on. Should this occur, take the power cord out of the wall outlet and put it back in again.

E-69

Page 69 Page 71
Image 70
Page 69 Page 71
Contents XG-V10XU Introduction EnglishPower Sources CleaningAccessories Power-Cord ProtectionImportant Safeguards Using the Terminal Cover Temperature Monitor FunctionUsing the Carrying Handle Lamp Monitor FunctionOutstanding Features High-end LCD Projector with Ultra High BrightnessNetwork Capability Contents Maintenance For Windows For Macintosh To Install Acrobat Reader from the CD-ROMFor other operating systems For other languages Part Names ProjectorPart Names Battery Cover Compartment Remote ControlInserting the batteries Supplied Accessories RRMCG1564CESAConnecting the Projector to a Computer Power SupplyConnecting the Power Cord ConnectionsPlug and Play function when connecting to a 15-pin terminal Projecting Computer ImagesConnecting to a computer using the RS-232CPort ComputerWatching Video Images and Laser Disc Images Laser disc playerFor Better Sound Connecting to an amplifier and other audio componentsWatching DVD and Digital TV Images AmplifierPress Power on Power ON/OFFTurning on the Main Power Press Power OFFUsing the Adjustment Feet Setting Up the ScreenUsing the Adjustment Feet DownThrow Distance Adjusting the Projection DistanceStandard Setup Front Projection Computer and Video InputComputer and Video Adjusting the Projection DistanceThrow distance ratio 1.9 to InputAN-LV18MX Throw distance ratio 0.9AN-LV26EZ Throw distance ratio 1.2 to 1.4AN-LV36EZ Throw distance ratio 1.7 to 2.7AN-LV55EZ Throw distance ratio 2.6 to 3.7AN-LV80EZ Throw distance ratio 3.8 to 5.3Upper and Lower Lens Shift Position Upper and Lower Lens Shift Position Ceiling MountLens Button Digital Image AdjustmentsDigital Shift Rear Projection Projection Using a MirrorImage Projection Ceiling-mount ProjectionAdjusting the Volume Using the Operation ButtonsSelecting the Input Signal Source Projector Remote ControlDisplaying a Still Image Superimposing a Black ScreenProjected Image Magnifying a Specific Portion of an Image On-screen Display Remote ControlWhen Input 1.2.3 or Input 4.5.6 is pressed ProjectorAdjusting the Picture Aspect Ratio ComputerGamma Correction Function Projector On-screen Display Remote ControlGamma Modes Using the Remote Control as a Wireless Mouse Selecting the Remote Control ModeOperating the Remote Control Remote Control/Mouse Receiver PositioningOperating the Remote Control Use as a Wireless MouseMouse mode buttons Connecting to the USB port on a PC or Macintosh Connecting the Mouse ReceiverConnecting the Remote Mouse Receiver Connecting to the PS/2 port on a PCWired Remote Control Using as a Laser PointerUsing as a Wired Remote Control Use as a Laser PointerBasic Operations Using the GUI Graphical User Interface Menu ScreenInput 1, 2 RGB or 3 Digital mode Input 4, 5 Video mode GUI On-screen DisplayMain menu Items on the Input 1, 2 or 3 Mode Menu BarMenu Bars Sub menuItems on the Input 4 or 5 Mode Menu Bar Menu BarsDescription of Adjustment Items Adjusting the PictureGUI On-screen Display RGB input in Input 1 or 2 mode Description of Color Temperature Adjusting the Color TemperatureAdjusting the Picture Projector Remote Control GUI On-screen DisplayGUI On-screen Display Projector Remote Control Selecting the Signal TypeProgressive Mode Adjusting the Computer Images RGB menu only Saving the adjustment setting Saving and Selecting Adjustment SettingsAdjusting the Computer Images RGB menu only Selecting a saved settingSpecial Mode Adjustment Checking the Input SignalAuto Sync Display Function When Auto Sync is set to onOn-screen Display GUI On-screen Display Adjusting the Sound Displaying Dual Pictures RGB menu only Reducing Image Noise Video menu only Turning On/Off the On-screen Display Setting the Video Signal Video menu onlyDescription of OSD Display Description of Background Images Selecting a Background ImageSelecting a Startup Image Description of Startup ImagesDescription of Automatic Power Shutoff Selecting the Economy ModeAutomatic Power Shutoff Function Monitor Out/RS-232C Off FunctionID No. Display Off Function Selecting the Economy ModeReversing/Inverting Projected Images Description of ID No. DisplaySelecting the On-screen Display Language Displaying the Adjustment Settings To exit from the GUI, press MenuDeselecting Inputs Useful FeaturesLocking the Operation Buttons on the Projector Description of Keylock LevelsSelecting the Transmission Speed RS-232C Changing the Password Protecting Important Settings with a PasswordSetting the Password Setting the PasswordLAN Board 10BASE-T Setting Up the Optional BoardsNetwork Function SDI BoardSetting the ID No Setting the Stacking ModeControling Multiple Projectors with ID Numbers Projector Remote Control When selecting Sharp default image Projector Remote Control On-screen Display Menu WindowDisplaying the Break Time Operating the Network Function InternetMultiple and group projector control via computer Operating the Network FunctionStack Projection Videowall Maintenance Indicators Lamp/Maintenance IndicatorsMaintenance Indicator Condition Problem Possible Solution Confirming the Lamp Usage Time Lamp MaintenanceCondition Problem Possible Solution LampMode can be set to double the effective lamp usage Setting the Lamp ModeDescription of Lamp Mode Replacing the LampReplacing the Lamp Removing and installing the lamp unitTurn on the main power Attach the lamp cage coverReplacing the Air Filter Unplug the power cordReplacing the front air filter Problem Check TroubleshootingFor Sharp Assistance U.S.A. only Types of Presentations Guide to Effective PresentationsCreative Presentations Guide to Effective Presentations FontsSet-Up Good BadRehearsing & Delivery Presentation TipsConnecting Pin Assignments DVI Port 29-pinPC control RS-232C Specifications and Command SettingsCommands Communication conditionsRS-232C Specifications and Command Settings Model Name Sharp remote control signal format Wired Remote Control Terminal SpecificationsSpecifications of wired remote control input Function and transmission codesComputer Compatibility Chart VGADimensions Units inches mmSpecifications PAL/PAL 60/PAL-M/PAL-N/SECAM/NTSC 3.58/NTSCGlossary Aspect ratioIndex DOT by DOTSharp Corporation

XG-V10XU specifications

The Sharp XG-V10XU is a high-performance LCD projector designed for professional environments, offering a blend of advanced features and user-friendly technologies that enhance presentations and visual experiences. With a native resolution of XGA (1024x768), the projector provides clear and precise image quality, making it suitable for both business applications and educational purposes.

One of the standout features of the XG-V10XU is its impressive brightness, boasting 2500 ANSI lumens. This allows the projector to perform well in various lighting conditions, ensuring that images and presentations remain visible even in well-lit rooms. Coupled with a high contrast ratio of 400:1, the projector delivers vibrant colors and deep blacks, enhancing overall image depth and clarity.

The XG-V10XU employs advanced image technologies, including a 3LCD system, which works to create rich and accurate color reproduction. This technology minimizes color break-up and ensures that the projector can handle a wide range of media, from detailed graphs to vivid videos, with excellent fidelity. Additionally, the projector features various image modes that allow users to adjust settings to match different content types, such as presentations, video playback, or photo exhibitions.

Versatility is another strong point of the Sharp XG-V10XU. It supports a variety of input sources, including VGA, composite video, S-Video, and HDMI, making it compatible with multiple devices such as laptops, DVD players, and gaming consoles. This flexibility is augmented by its built-in 10-watt speaker, enabling users to present audio alongside visuals without needing external sound equipment.

Portability is also a key characteristic of the XG-V10XU. Weighing in at around 2.8 kg, it is designed for ease of transport, making it an excellent choice for traveling professionals or educators who need to move between locations. The projector’s compact dimensions do not compromise build quality, as Sharp incorporates durable materials to ensure longevity under regular use.

Additionally, the Sharp XG-V10XU includes features such as a digital keystone correction to adjust image distortions, facilitating quick setup in varied environments. With a lengthy lamp life of approximately 4000 hours, maintenance is minimized, allowing users to focus on their presentations rather than equipment downtime. Overall, the Sharp XG-V10XU stands out as a reliable and effective solution for those in need of a quality projector that combines ease of use with exceptional performance.
Top Page Image Contents