Runco VX-2i manual Aspect Ratio Selection Buttons, ANA Anamorphic 3 For 169 DVDs 4X3 Standard 43

Page 20

Controls and Functions

9.Aspect Ratio Selection Buttons

Use the red buttons to select an aspect ratio directly or to enter numeric characters, as follows:

ANA (Anamorphic) (3) For 16:9 DVDs.

4X3 (Standard 4:3) (6)

The input signal is scaled to fit 4:3 display mode in the center of the screen.

LETBOX (Letterbox) (9)

Image in letterbox format is enlarged to fit 16:9 full screen display and the upper/ lower portions are “blanked off.”

V-WIDE (VirtualWide)

4:3 image is enlarged NON-linearly in horizontal direction to fit 16:9 full screen display.

10.S-VID 1 (4) / S-VID 2 (5) (S-Video)

Press to select an S-Video input or to enter the numeric character “4” or “5.”

11.HD 1 (7) / HD 2 (8)

Press to select a HD (RGBHV or YPbPr component) input or to enter the numeric character “7” or “8.”

12.DVI 1 / DVI 2 (0)

Press to select a Digital Video input. Press DVI2 to enter the numeric character “0.”

10	Runco VX-2i Owner’s Operating Manual

Image 20

Contents VX-2i Page TWO Year Limited Warranty For Projectors, Video Processors and ControllersEffective Warranty Date Runco INTERNATIONAL, INC Safety Precautions Table of Contents Maintenance and Troubleshooting SpecificationsOperation Serial CommunicationsList of Figures List of Figures Introduction About This ManualUsing This Manual If you need Turn toDescription, Features and Benefits Key Features and BenefitsOptional Accessories Controls and Functions VX-2i at a GlanceComponent Video RCA connectors HD1 / HD2 Analog BNC connectorsVolt 800 mA Trigger Outputs Video 1 / S-VIDEOVX-2i Remote Control Power Input 100 to 240 VAC Connect the VX-2i to power hereOn / OFF Cursor KeysVideo Comp ComponentAspect Ratio Selection Buttons ANA Anamorphic 3 For 169 DVDs 4X3 Standard 43Letbox Letterbox Wide VirtualWideInstallation Remote ControlQuick Setup Step Procedure For Details, Refer toInstallation Considerations Installation TypeFlat vs. Curved Screens Throw Distance Ambient LightOther Considerations Throw Ratio Throw Distance Range Lens Option Note Throw Dist Screen Width Minimum MaximumLens Shift Vertical and HorizontalPosition Vertical Lens Shift Adjusting the Projection AngleMounting Folded OpticsConnector Panel Access Connecting the VX-2i toConnections to VX-2iDigital DTV RGB Connections See Figure Digital DTV RGB ConnectionsAnalog Computer RGB Connections See Figure Analog RGB ConnectionsComposite/S-Video/Component Video Connections See Figure 10. Composite, S-Video and Component Video ConnectionsConnecting 12-Volt RS-232 ControllerConnection Trigger Outputs toOperation Turning on the PowerAdjusting the Picture Orientation Focus Zoom Shift Lens AdjustmentsUsing the On-Screen Menus ISF Presets ServiceInput Source Aspect RatioMain Menu Input SourceAspect Ratio Input Source Composite Video Component SDAspect Ratio Settings Remote Aspect Ratio Control Description KeyPicture Picture Brightness Contrast Color Tint SharpnessTypical Gray Bar Pattern for Adjusting Contrast Gray Yellow Cyan Green Magenta Red Blue Input Position Input Position Left/Right Up/Down Width Height OverscanISF Presets InformationCalibration Should be used by ISF-certified technicians onlyOperation Service Tip Operation Symptom Possible Causes Solution Maintenance and TroubleshootingLamp Replacement Troubleshooting Tips Maintenance and Troubleshooting RS-232 Connection and Port Configuration Serial Command SyntaxCommand Parameter Value Description Min/max Stored? Serial CommunicationsSerial Communications Night YES SHARPNESS? Specifications VX-2i SpecificationsHome Theater Calibration Specifications Industry-Standard SpecificationsPower Requirements DimensionsLimited Warranty Specifications are subject to change without noticeVX-2i Dimensions VX-2i DimensionsPage Runco CL-810 Owner’s Operating Manual