Runco VX-2i manual Operation

Page 48

Operation

HD Format: If for some reason the VX-2i does not properly detect the incoming signal format (color space) on the HD1 or HD2 inputs, specify it here (RGB or YUV). Otherwise, leave it set to Auto.

Triggers: Select Triggers from the Service menu to configure the 12-volt trigger outputs. You can assign one or more trigger outputs to each aspect ratio. Those triggers are then activated by selecting that aspect ratio.

If your projector is equipped with the Runco CineWide with AutoScope system, assign at least one trigger output (the same one to which the lens motor is connected) to the Cinema and Virtualwide 2.35 aspect ratios.

Miscellaneous: Select Miscellaneous from the Service menu to set the following options:

•Menu Mode: This is the manner in which the OSD menus appear and disappear when you press MENU. Choose one of the following:

0 = No transition; menus abruptly appear and disappear.

1 = Menus fade in and out.

2 = “Checkerboard” dissolve; menus appear and disappear in sections.

3 = “Window shade” effect; menus are drawn on a diagonal from top left to bottom right, and retract in the opposite direction.

•Timeout - Short/Long: These settings control how long the OSD menus stay on screen. Select a time-out period of from 2 to 60 seconds.

•Side Bar Color: This controls the color of the inactive image area. The range is from -100 (black) to 100 (white).

The inactive image area is on either side of the active image area when using the Standard 4:3 aspect ratio, and above and below the active image area when using the Letterbox aspect ratio.

System Reset: To reset ALL projector settings (including image settings) back to their

factory defaults, choose System Reset from the Service menu. Select Confirm to continue or Back to cancel. This action is not undoable. Use it with caution!

38	Runco VX-2i Owner’s Operating Manual

Image 48

Contents VX-2i Page TWO Year Limited Warranty For Projectors, Video Processors and ControllersEffective Warranty Date Runco INTERNATIONAL, INC Safety Precautions Table of Contents Maintenance and Troubleshooting SpecificationsOperation Serial CommunicationsList of Figures List of Figures Introduction About This ManualUsing This Manual If you need Turn toDescription, Features and Benefits Key Features and BenefitsOptional Accessories Controls and Functions VX-2i at a GlanceComponent Video RCA connectors HD1 / HD2 Analog BNC connectorsVolt 800 mA Trigger Outputs Video 1 / S-VIDEOVX-2i Remote Control Power Input 100 to 240 VAC Connect the VX-2i to power hereOn / OFF Cursor KeysVideo Comp ComponentAspect Ratio Selection Buttons ANA Anamorphic 3 For 169 DVDs 4X3 Standard 43Letbox Letterbox Wide VirtualWideInstallation Remote ControlQuick Setup Step Procedure For Details, Refer toInstallation Considerations Installation TypeFlat vs. Curved Screens Ambient Light Other ConsiderationsThrow Distance Throw Ratio Throw Distance Range Lens Option Note Throw Dist Screen Width Minimum MaximumVertical and Horizontal PositionLens Shift Vertical Lens Shift Adjusting the Projection AngleMounting Folded OpticsConnector Panel Access Connecting the VX-2i toConnections to VX-2iDigital DTV RGB Connections See Figure Digital DTV RGB ConnectionsAnalog Computer RGB Connections See Figure Analog RGB ConnectionsComposite/S-Video/Component Video Connections See Figure 10. Composite, S-Video and Component Video ConnectionsConnecting 12-Volt RS-232 ControllerConnection Trigger Outputs toTurning on the Power Adjusting the Picture OrientationOperation Lens Adjustments Using the On-Screen MenusFocus Zoom Shift ISF Presets ServiceInput Source Aspect RatioMain Menu Input SourceAspect Ratio Input Source Composite Video Component SDAspect Ratio Settings Remote Aspect Ratio Control Description KeyPicture Picture Brightness Contrast Color Tint SharpnessTypical Gray Bar Pattern for Adjusting Contrast Gray Yellow Cyan Green Magenta Red Blue Input Position Input Position Left/Right Up/Down Width Height OverscanISF Presets InformationCalibration Should be used by ISF-certified technicians onlyOperation Service Tip Operation Maintenance and Troubleshooting Lamp Replacement Troubleshooting TipsSymptom Possible Causes Solution Maintenance and Troubleshooting RS-232 Connection and Port Configuration Serial Command SyntaxCommand Parameter Value Description Min/max Stored? Serial CommunicationsSerial Communications Night YES SHARPNESS? Specifications VX-2i SpecificationsHome Theater Calibration Specifications Industry-Standard SpecificationsPower Requirements DimensionsLimited Warranty Specifications are subject to change without noticeVX-2i Dimensions VX-2i DimensionsPage Runco CL-810 Owner’s Operating Manual