Runco VX-2i manual Home Theater Calibration Specifications, Industry-Standard Specifications, Lamp

Page 56

Specifications

Table 7-1. VX-2i Specifications (continued)

Brightness and Contrast:

Cinema Standards Measurement System (CSMS)

 

Specifications

 

-

Brightness: 52.1 foot-Lamberts (fL)

 

-

Contrast Ratio: 217:1

 

These measurements are taken from the projector in a controlled,

 

home theater environment. All measurements are made to

 

ANSI/NAPM IT7.228-1997 specifications using the Photo Research

 

PR-650 SpectraColorimeter and Minolta LS-100 Luminance Meter,

 

Video Essentials test DVD and a 1.3 gain, 72-inch wide screen. The

 

projector is calibrated to a color temperature of 6,500K and has a

 

minimum of 150 hours of usage.

 

The foot-Lambert (fL) is the unit of measurement used in commercial

 

movie theaters to express image brightness at the screen surface. The

 

Society of Motion Picture and Television Engineers (SMPTE) specifies

 

16 fL as the target image brightness for film-based projectors using an

 

open gate (without film in the projector). More importantly, today

 

SMPTE specifies 12 fL as the target image brightness in Digital

 

Cinema theaters. The foot-Lambert measurement is dependent on

 

screen size, screen gain and projector light output.

 

Home Theater Calibration Specifications

 

-

Light Output: 1227 ANSI Lumens

 

-

Contrast Ratio: 217:1

 

These specifications are obtained by calibrating the projector as

 

described above for CSMS measurements.

 

Industry-Standard Specifications

 

-

Light Output: 2500 ANSI Lumens

 

-

Contrast Ratio: 2800:1

 

These are typical projector brightness and contrast specifications

 

found in most companies’ sales literature. Runco includes these

 

measurements in its literature to allow for direct comparison with other

 

manufacturers’ projectors. These measurements are typically taken at

 

9,000K to 13,000K to get expected performance data when the

 

projector is used in professional, commercial and industrial displays.

 

 

Lamp:

275 Watts

 

 

Estimated Lamp Life:

2000 hours

 

 

Inputs:

(1) Composite; (2) S-Video; (1) Component; (2) HD-R (Pr), G

 

(Y), B (Pb), H, V; (2) DVI w/HDCP

 

 

 

Control Options:

-

Built-in keypad

 

-

Discrete infrared remote

 

-

Serial commands via RS-232

 

 

Trigger Outputs:

3 x 12 VDC, 800 mA

 

 

Bandwidth:

150 Mega Samples/Second (MSPS)

 

 

Power Requirements:

100 to 240 VAC (auto-sensing), 50/60 Hz, 610 Watts

 

 

Operating Environment:

41°F to 95°F (5°C to 35°C), 0% to 90% humidity

 

(non-condensing)

 

 

Dimensions:

See Figure 7-1

 

 

Weight (without lens):

65 lbs. (29.48 kg)

 

 

Regulatory Approvals:

Complies with FCC, CE C-Tick

 

 

 

46

Runco VX-2i Owner’s Operating Manual

Page 55 Page 57
Image 56
Page 55 Page 57
Contents VX-2i Page TWO Year Limited Warranty For Projectors, Video Processors and ControllersEffective Warranty Date Runco INTERNATIONAL, INC Safety Precautions Table of Contents Maintenance and Troubleshooting SpecificationsOperation Serial CommunicationsList of Figures List of Figures Introduction About This ManualUsing This Manual If you need Turn toDescription, Features and Benefits Key Features and BenefitsOptional Accessories Controls and Functions VX-2i at a GlanceComponent Video RCA connectors HD1 / HD2 Analog BNC connectorsVolt 800 mA Trigger Outputs Video 1 / S-VIDEOVX-2i Remote Control Power Input 100 to 240 VAC Connect the VX-2i to power hereOn / OFF Cursor KeysVideo Comp ComponentAspect Ratio Selection Buttons ANA Anamorphic 3 For 169 DVDs 4X3 Standard 43Letbox Letterbox Wide VirtualWideInstallation Remote ControlQuick Setup Step Procedure For Details, Refer toInstallation Considerations Installation TypeFlat vs. Curved Screens Throw Distance Ambient LightOther Considerations Throw Ratio Throw Distance Range Lens Option Note Throw Dist Screen Width Minimum MaximumLens Shift Vertical and HorizontalPosition Vertical Lens Shift Adjusting the Projection AngleMounting Folded OpticsConnector Panel Access Connecting the VX-2i toConnections to VX-2iDigital DTV RGB Connections See Figure Digital DTV RGB ConnectionsAnalog Computer RGB Connections See Figure Analog RGB ConnectionsComposite/S-Video/Component Video Connections See Figure 10. Composite, S-Video and Component Video ConnectionsConnecting 12-Volt RS-232 ControllerConnection Trigger Outputs toOperation Turning on the PowerAdjusting the Picture Orientation Focus Zoom Shift Lens AdjustmentsUsing the On-Screen Menus ISF Presets ServiceInput Source Aspect RatioMain Menu Input SourceAspect Ratio Input Source Composite Video Component SDAspect Ratio Settings Remote Aspect Ratio Control Description KeyPicture Picture Brightness Contrast Color Tint SharpnessTypical Gray Bar Pattern for Adjusting Contrast Gray Yellow Cyan Green Magenta Red Blue Input Position Input Position Left/Right Up/Down Width Height OverscanISF Presets InformationCalibration Should be used by ISF-certified technicians onlyOperation Service Tip Operation Symptom Possible Causes Solution Maintenance and TroubleshootingLamp Replacement Troubleshooting Tips Maintenance and Troubleshooting RS-232 Connection and Port Configuration Serial Command SyntaxCommand Parameter Value Description Min/max Stored? Serial CommunicationsSerial Communications Night YES SHARPNESS? Specifications VX-2i SpecificationsHome Theater Calibration Specifications Industry-Standard SpecificationsPower Requirements DimensionsLimited Warranty Specifications are subject to change without noticeVX-2i Dimensions VX-2i DimensionsPage Runco CL-810 Owner’s Operating Manual
Top Page Image Contents