Runco VX-2i manual ISF Presets, Information, Calibration

Page 44

Operation

ISF Presets ➤

ISF Presets

7

ISF Night

 

… ISF Day

 

… Custom 1

Save

… Custom 2

Save

Factory Default

 

Information ➤

Information

Serial Number Hardware

Firmware

Date

Overscan: Image Overscan pushes the outside edge of the active picture area of the video signal out beyond the edge of the display area.

Some television programs are produced based on the assumption that older television sets may not display the outer edges of the broadcast picture area. Over scan effectively trims away these inactive, outer edges and enlarges the remaining portion of the image to fill the display area.

Select from 1% to 10% of Overscan, as desired.

For HDTV, DVDs and other video sources, Overscan is generally not necessary or desirable.

For each input, the VX-2i lets you save image quality settings as presets that you can recall at a later time. You can create up to four presets per input and resolution. Use the ISF Presets menu to recall saved image presets, or to save image settings in the “Custom 1” or “Custom 2” memory location. The currently-selected preset is indicated by a “7” to its left; in the example shown here, ISF Night is selected.

You should save changes to any of the following settings to a preset; otherwise they will be lost when a new input source or resolution is selected:

•Aspect ratio

•Picture quality settings (brightness, contrast, color saturation, tint and sharpness)

•Input position (image position, width, height and overscan percentage)

To reset all image presets to their factory defaults, select Factory Default and press

ENTER.

Select Information from the Main Menu to see information that uniquely identifies your projector: its serial number, the installed hardware and firmware versions and the firmware version build date. Should you ever need to contact Runco Technical Support, this information will help them answer your questions or resolve product performance issues.

Calibration ➤

Calibration

ISF Night

Display Color

Input Image

Input Color

ISF Day

Display Color

Input Image

Input Color

Use the Calibration menu to perform advanced picture quality adjustments. This menu

should be used by ISF-certified technicians only.

You must enter a passcode to access the Calibration menu.

Note

The changes you make here take effect immediately; you do not need to save them. To recall the ISF Night or ISF Day settings, select “ISF Night” or “ISF Day” from the ISF Presets menu (see above).

34

Runco VX-2i Owner’s Operating Manual

Page 43 Page 45
Image 44
Page 43 Page 45
Contents VX-2i Page TWO Year Limited Warranty For Projectors, Video Processors and ControllersEffective Warranty Date Runco INTERNATIONAL, INC Safety Precautions Table of Contents Maintenance and Troubleshooting SpecificationsOperation Serial CommunicationsList of Figures List of Figures Introduction About This ManualUsing This Manual If you need Turn toDescription, Features and Benefits Key Features and BenefitsOptional Accessories Controls and Functions VX-2i at a GlanceComponent Video RCA connectors HD1 / HD2 Analog BNC connectorsVolt 800 mA Trigger Outputs Video 1 / S-VIDEOVX-2i Remote Control Power Input 100 to 240 VAC Connect the VX-2i to power hereOn / OFF Cursor KeysVideo Comp ComponentAspect Ratio Selection Buttons ANA Anamorphic 3 For 169 DVDs 4X3 Standard 43Letbox Letterbox Wide VirtualWideInstallation Remote ControlQuick Setup Step Procedure For Details, Refer toInstallation Considerations Installation TypeFlat vs. Curved Screens Throw Distance Ambient LightOther Considerations Throw Ratio Throw Distance Range Lens Option Note Throw Dist Screen Width Minimum MaximumLens Shift Vertical and HorizontalPosition Vertical Lens Shift Adjusting the Projection AngleMounting Folded OpticsConnector Panel Access Connecting the VX-2i toConnections to VX-2iDigital DTV RGB Connections See Figure Digital DTV RGB ConnectionsAnalog Computer RGB Connections See Figure Analog RGB ConnectionsComposite/S-Video/Component Video Connections See Figure 10. Composite, S-Video and Component Video ConnectionsConnecting 12-Volt RS-232 ControllerConnection Trigger Outputs toOperation Turning on the PowerAdjusting the Picture Orientation Focus Zoom Shift Lens AdjustmentsUsing the On-Screen Menus ISF Presets ServiceInput Source Aspect RatioMain Menu Input SourceAspect Ratio Input Source Composite Video Component SDAspect Ratio Settings Remote Aspect Ratio Control Description KeyPicture Picture Brightness Contrast Color Tint SharpnessTypical Gray Bar Pattern for Adjusting Contrast Gray Yellow Cyan Green Magenta Red Blue Input Position Input Position Left/Right Up/Down Width Height OverscanISF Presets InformationCalibration Should be used by ISF-certified technicians onlyOperation Service Tip Operation Symptom Possible Causes Solution Maintenance and TroubleshootingLamp Replacement Troubleshooting Tips Maintenance and Troubleshooting RS-232 Connection and Port Configuration Serial Command SyntaxCommand Parameter Value Description Min/max Stored? Serial CommunicationsSerial Communications Night YES SHARPNESS? Specifications VX-2i SpecificationsHome Theater Calibration Specifications Industry-Standard SpecificationsPower Requirements DimensionsLimited Warranty Specifications are subject to change without noticeVX-2i Dimensions VX-2i DimensionsPage Runco CL-810 Owner’s Operating Manual
Top Page Image Contents