Runco VX-2i manual Gray Yellow Cyan Green Magenta Red Blue

Page 42

Operation

Color Saturation: On your external test pattern source, select a color bar pattern like the one shown in Figure 4-4.

gray

yellow

cyan

green

magenta

red

blue

Figure 4-4. Typical Color Bar Pattern for Adjusting Color Saturation and Tint

Select Color and press ENTER. While looking at the color bar pattern through a blue filter, adjust the color saturation level until the outermost (gray and blue) color bars appear to be a single shade of blue:

gray

yellow

cyan

green

magenta

red

blue

Tint: Tint or “hue” is essentially the ratio of red to green in the color portion of the image. When tint is decreased, the image appears redder; when it is increased the image appears greener. To set the tint, select Tint and press ENTER. While looking at the color bar pattern through a blue filter, adjust the tint level until the cyan and magenta color bars (on either side of the green bar) appear to be a single shade of blue.

Like the brightness and contrast controls, the color and tint controls

Note are interactive. A change to one may require a subtle change to the other in order to achieve the optimum setting.

32

Runco VX-2i Owner’s Operating Manual

Image 42
Contents VX-2i Page TWO Year Limited Warranty For Projectors, Video Processors and ControllersEffective Warranty Date Runco INTERNATIONAL, INC Safety Precautions Table of Contents Operation Maintenance and TroubleshootingSpecifications Serial CommunicationsList of Figures List of Figures Introduction About This ManualUsing This Manual If you need Turn toDescription, Features and Benefits Key Features and BenefitsOptional Accessories Controls and Functions VX-2i at a GlanceComponent Video RCA connectors HD1 / HD2 Analog BNC connectorsVolt 800 mA Trigger Outputs Video 1 / S-VIDEOVX-2i Remote Control Power Input 100 to 240 VAC Connect the VX-2i to power hereVideo On / OFFCursor Keys Comp ComponentLetbox Letterbox Aspect Ratio Selection ButtonsANA Anamorphic 3 For 169 DVDs 4X3 Standard 43 Wide VirtualWideInstallation Remote ControlQuick Setup Step Procedure For Details, Refer toInstallation Considerations Installation TypeFlat vs. Curved Screens Ambient Light Other ConsiderationsThrow Distance Throw Ratio Throw Distance Range Lens Option Note Throw Dist Screen Width Minimum MaximumVertical and Horizontal PositionLens Shift Vertical Lens Shift Mounting Adjusting the ProjectionAngle Folded OpticsConnections to Connector Panel AccessConnecting the VX-2i to VX-2iDigital DTV RGB Connections See Figure Digital DTV RGB ConnectionsAnalog Computer RGB Connections See Figure Analog RGB ConnectionsComposite/S-Video/Component Video Connections See Figure 10. Composite, S-Video and Component Video ConnectionsConnection Connecting 12-VoltRS-232 Controller Trigger Outputs toTurning on the Power Adjusting the Picture OrientationOperation Lens Adjustments Using the On-Screen MenusFocus Zoom Shift Input Source ISF PresetsService Aspect RatioAspect Ratio Main MenuInput Source Input Source Composite Video Component SDAspect Ratio Settings Remote Aspect Ratio Control Description KeyPicture Picture Brightness Contrast Color Tint SharpnessTypical Gray Bar Pattern for Adjusting Contrast Gray Yellow Cyan Green Magenta Red Blue Input Position Input Position Left/Right Up/Down Width Height OverscanCalibration ISF PresetsInformation Should be used by ISF-certified technicians onlyOperation Service Tip Operation Maintenance and Troubleshooting Lamp Replacement Troubleshooting TipsSymptom Possible Causes Solution Maintenance and Troubleshooting Command Parameter Value Description Min/max Stored? RS-232 Connection and Port ConfigurationSerial Command Syntax Serial CommunicationsSerial Communications Night YES SHARPNESS? Specifications VX-2i SpecificationsPower Requirements Home Theater Calibration SpecificationsIndustry-Standard Specifications DimensionsLimited Warranty Specifications are subject to change without noticeVX-2i Dimensions VX-2i DimensionsPage Runco CL-810 Owner’s Operating Manual