Runco PFP-7, Vivix Pixel for Pixel, PFP-11 manual Screen Type, Scan Rate/Resolution

Page 19

Screen Type

When you are installing the processor for the first time, the first order of business is to define what type of screen will be used with this system. If a 1.78:1 (16:9) or 1.85:1 screen is used, highlight 16:9 SCREEN and press ENTER. If a standard 4:3 screen is installed, highlight 4:3 SCREEN and press enter. However, if your display is a native 16:9 aspect ratio (such as most plasmas), you only need to select the actual resolution of the device. The PFP-7/PFP-11 will automatically switch itself to the proper mode.

The purpose of defining the screen type is to tell the processor how to create aspect ratios (see page 27 for a definition of aspect ratios). For example, on a 16:9 screen, the letterbox and anamorphic aspect ratios will use the entire 16:9 screen, and the 4:3 aspect ratio will be displayed in the center of the 16:9 screen (you'd have 'black bars' on the left and right sides of the image).

On the other hand, on a 4:3 screen, the 4:3 aspect ratio would fill the screen, but the letterbox and anamorphic aspect ratios would be displayed in the center of the screen vertically (there would be 'black bars' on the top on bottom of the image).

Important note on aspect ratios for 4:3 screens: If 4:3 SCREEN is selected, the only way the processor will provide all three aspect ratios is if one of the FIXED PIXEL scan rates are selected

(i.e. 1024 x 768). The processor will NOT provide three aspect ratios on a 4:3 screen if 480p, 540p, 600p or 720p are selected. The reason for this is that CRT projectors will provide the best resolution if two separate memories are created by the projector itself, one for anamorphic, one for full 4:3. This way, the CRT projec- tor can provide the maximum number of lines of resolution on either aspect ratio since it is simply compress- ing a 4:3 image to an anamorphic image. Therefore, Runco recommends that the CRT projector create the aspect ratios on 4:3 screens (if possible) for best results.

For fixed pixel displays, the number of pixels cannot be changed nor do many of the displays provide the ability to create aspect ratios. Therefore, the PFP-7/PFP-11will provide three full aspect ratios for fixed pixel displays (WHEN a fixed-pixel scan rate is selected) for use on 4:3 screens.

In any event, if 16:9 SCREEN is selected, the PFP-7/PFP-11will provide three aspect ratios regardless of the selection of the scan rate type or display device used.

Scan Rate/Resolution

SCAN RATE is how many lines of resolution can be output in a single image. For example, 540p means that there are 540 visible lines of resolution, and 'p' means the signal is PROGRESSIVE. A Progressive output is where ALL lines of resolution will be displayed during each frame as opposed to an INTERLACED signal, which only displays half the lines of the frame during one field and the other half the next. Progressive outputs are far better than Interlaced outputs as all lines of resolution are always displayed, and fixed-pixel displays produce far better results when using a progressive signal. The fixed-pixel outputs are also progres- sive, but are referred to in PIXELS (Picture Elements) as opposed to the actual number of lines of resolution. This is because fixed-pixel displays are referred to in their native resolution in pixels, i.e. 1024 x 768 (meaning 1024 vertical rows of pixels and 768 horizontal rows of pixels).

Selecting a scan rate (resolution) for your display device is an extremely important task. The first thing that should be done is to determine what resolution will provide the best results for your display. The following are some guidelines that will assist you in determining the best possible results for your type of projector.

18

Image 19
Contents PFP-7/PFP-11 PFP-7/PFP-11 Page Contents Remarque DOC compliance Notice Safety TipsDOC avis de conformation Introduction Features and BenefitsGeneral Description Front Panel Front and Rear Panel DescriptionsRGB Video Output Video Inputs Rear PanelPower Input Power Button Remote Control DescriptionConnection Examples Quick SET-UP GuideGetting Started Compatibility Overall Functional DescriptionMain Menu Menu Description and NavigationWhite Yellow Cyan Green Magenta Red Blue Picture Quality AdjustmentsPage Installation Menu Screen Type Scan Rate/ResolutionTo select a resolution, follow this procedure Selecting a Resolution Scan RateFixed Pixel Displays Output Format Menu Output Format SyncSide Bar Level Image Shift Runco PFP-7 Side Bar Level 013To reset your PFP-7/PFP-11, follow this procedure System ResetBlanking Aspect Ratios Active image area Actual screen area Blanked cut off Areas Top DimensionsSide Other notes RS-232 CommunicationsDescription RS-232 CommandsStore YES Specifications Page RUMA-006200 rev