Serial Communications
Table 6-2. Serial Commands (continued)
Operation | Commands | Values | Notes |
status | ? | 0 | = Standby |
|
| ||
|
| 1 | = Powering Up |
|
| 2 | = Displaying |
|
| 3 | = Cooling Down |
|
| 4 | = Error |
| errcode | ? |
|
|
|
|
| Refer to | ||
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
| Codes, below. |
|
|
|
|
|
|
|
|
|
|
|
|
| msgbox | = ? |
|
|
|
| 0 = On | This control enables or | ||
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
| 1 = Off | disables the display of |
|
|
|
|
|
|
|
|
|
| power off, source and |
|
|
|
|
|
|
|
|
|
| adjustment message |
|
|
|
|
|
|
|
|
|
| boxes (brightness, con- |
|
|
|
|
|
|
|
|
|
| trast etc.). Default value is |
|
|
|
|
|
|
|
|
|
| ON. |
|
|
|
|
|
|
|
|
|
|
|
| cal.text1 | = |
|
|
|
|
| Up to 30 characters. | The | |
| cal.text2 |
|
|
|
|
|
|
|
| screen is customizable |
|
|
|
|
|
|
|
|
|
| |
| cal.text3 |
|
|
|
|
|
|
|
| with three lines of text of |
|
|
|
|
|
|
|
|
| up to 30 characters each. | |
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
| This text appears below |
|
|
|
|
|
|
|
|
|
| the “CALIBRATED FOR:” |
|
|
|
|
|
|
|
|
|
| text in the logo screen. |
|
|
|
|
|
|
|
|
|
| The allowable characters |
|
|
|
|
|
|
|
|
|
| are all numbers, letters |
|
|
|
|
|
|
|
|
|
| (uppercase and lower- |
|
|
|
|
|
|
|
|
|
| case), spaces, and sym- |
|
|
|
|
|
|
|
|
|
| bols available in the ASCII |
|
|
|
|
|
|
|
|
|
| code set. |
|
|
|
|
|
|
|
|
| ||
| If an errcode ? command returns one of the following values, you have encountered a | |||||||||
| likely system error requiring the attention of a qualified service technician. Try resetting the | |||||||||
| projector by powering it off, allowing it to cool and powering it on again. Refer to Table | |||||||||
| and contact your dealer if the problem persists. |
| ||||||||
| The specific code number identifies the source of the error detected, and is particularly | |||||||||
| useful in cases where the projector is far away. For example, the code “7” means that | |||||||||
| Fan 1 has failed. |
|
|
|
|
|
|
|
|
|
| Table |
|
| |||||||
|
|
|
|
|
|
|
|
|
|
|
| Error Code | LED Indication |
|
| Description | |||||
|
|
|
|
|
|
|
|
|
|
|
| 0 |
|
|
|
|
|
|
| Inlet NTC thermal sensor is over temperature. | |
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
|
|
|
| 1 |
|
|
|
|
|
|
| DMD NTC thermal sensor is over temperature. | |
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
|
|
|
| 2 |
|
|
|
|
|
|
| Lamp 1 over temperature. | |
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
|
|
|
| 4 |
|
|
|
|
|
|
| Ballast 1 over temperature. | |
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
|
|
|
| 6 |
|
|
|
|
|
|
| Fan failure upon system | |
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
|
|
|
84 | Runco |