Runco LS-HB operation manual List of Figures

Page 15

List of Figures
2-1.LS-HB Front/Side View	5
2-2.LS-HB Rear/Bottom/Top View	7
2-3.LS-HB Rear Panel	9
3-1. IR Reception Angles	14
3-2. Estimating Throw Distance	17
3-3. Projector Placement	19
3-4. Vertical Lens Shift (Example Only)	19
3-5. Folded Optics	20
3-6. Projector with Fixed Anamorphic Lens Base Plate - Bottom View	26
3-7. Mounting Angle Ranges (Side-to-Side and Front-to-Back)	28
3-8. HDMI/DVI Source Connections	30
3-9. RGB Connections	31
3-10. SCART RGBS Connection	32
3-11. Component Video Connections	33
3-12. Composite and S-Video Connections	34
3-13.RS-232 Control System Connection	35
3-14.12-Volt Trigger Output Connection	36
3-15. External IR Receiver Connection	37
3-16. Anamorphic Lens Mounting Assembly - Exploded View	40
3-17. Attaching the Anamorphic Lens to the Lens Mount	42
4-1.LS-HB OSD Menu Structure	47
4-2.LS-HB Main Menu	48
4-3. Typical PLUGE Pattern for Adjusting Brightness	53
4-4. Typical Gray Bar Pattern for Adjusting Contrast	53
4-5. Typical Test Pattern for Adjusting Sharpness	54
4-6. Overscan Examples	56
4-7. Source Select Sub-Menu	57
4-8.LS-HB Advanced Menu	58
4-9. RGB Adjust Sub-Menu	60
4-10. Fine Sync Sub-Menu	61
4-11.LS-HB System Menu	62
4-12. Source Enable Sub-Menu	63
4-13. PIP and PBP areas for 1080p Display	64
4-14. PIP Split-Screen Mode	65

Runco LS-HB Installation/Operation Manual

xv

Image 15

Contents LS-HB Page RuncoCare Standard Features RuncoCare Standard Two Year Limited WarrantyRuncoCare Claim Procedure Extended Service Options Copyright and Trademarks Important Safety Instructions Declaration of Conformity Compliance InformationFCC Part Page Table of Contents Operation Maintenance and Troubleshooting SpecificationsSerial Communications Table of Contents Xiv List of Figures List of Figures About This Manual IntroductionIf you need Turn to Using This ManualDescription, Features and Benefits Optional Accessories LS-HB at a Glance Controls and FunctionsCursor Keys SourceLS-HB Rear/Bottom/Top View Runco Logo Badge RGB LS-HB Rear PanelOFF LS-HB Remote ControlTrigger 1 3.5-mm, mini phono jack RS-232Aspect Ratio Selection Button Memory Preset Buttons M1 / M2 / M3Picture Adjustment Buttons Contrast Sharpness Sharp Press to adjust sharpness Gamma GammaControls and Functions Installation Remote ControlOperation IR Reception Angles Quick Setup Step ProcedureFor Details, Refer Installation Installation TypeConsiderations Ambient Light Throw DistanceEstimating Throw Distance Lens Screen Lens Only Anamorphic Minimum Maximum Vertical and HorizontalPosition PrimaryCeiling Installation Floor InstallationLens Shift Folded Optics Anamorphic Lens Installing the Optional Anamorphic Lens MountInstalling the Movable Transport AssemblyAttaching the Transport Assembly Attachment Plate Ceiling Mount Plate Attachment Plate Projector bottom Do not OVER-TIGHTEN the ScrewsPlate Installation Anamorphic Lens Base PlateDo not use the mounting screws provided with the ceiling Mounting the LS-HB Angle Adjusting the ProjectionConnections to the LS-HB Connector Panel AccessConnecting Source Components to the LS-HBHDMI/DVI Connections See Figure Computer RGB Camcorder RGB ConnectionsGaming Console 10. Scart Rgbs ConnectionDTV-Set-Top Box 11. Component Video ConnectionsCamcorder 12. Composite and S-Video ConnectionsConnection RS-232 ControllerConnecting 12-Volt Trigger Output to ExternalTheater Equipment Is appropriate to your locale Connecting an External IRConnecting to AC Power ReceiverZoom Out Focus Zoom Turning on the Power Primary Lens AdjustmentsRear Projection Ceiling Mode Changing the OSD Language Adjusting the Picture OrientationIt is extremely important that the primary lens is properly Installing and Adjusting the Anamorphic LensAdjusting the Lens Height and Angle Correct Lens Angle Incorrect Lens Angle Tighten the knobs Installation Selecting An Input Source OperationSelecting Video Memory Selecting an Aspect RatioPIP Input Source Using Picture-In-Picture PIPUsing the On-Screen Menus LS-HB Main Menu 169 Aspect Ratio SettingsNarrow 169Native You must enter a passcode to access the Save ISF Typical Pluge Pattern for Adjusting Brightness Typical Test Pattern for Adjusting Sharpness Operation Overscan Examples Source Select Sub-Menu LS-HB Advanced Menu Same frame rate as the main source RGB Adjust Sub-Menu 10. Fine Sync Sub-Menu 11. LS-HB System Menu 12. Source Enable Sub-Menu PBP1 PBP2 14. PIP Split-Screen Mode Operation Language 15. LS-HB Service Menu OSD menus are not available when in test pattern mode Operation Lamp Replacement Maintenance and TroubleshootingSymptom Possible Causes Solution Troubleshooting TipsLS-HB Maintenance and Troubleshooting Serial Communications Key CommandsRS232 Remote Button IR Code Description Keyname Set Serial Command Key Names and IR CodesGam.crt Lit.tog Operations Control Commands Function Action on unitOperation Commands Values Serial CommandsSave.isf Resync Execute Color.space = ? Trans.menu = ? Soft.version Error Code LED Indication Description RS-232 Error CodesFan 1 failed Serial Communications LS-HB Specifications SpecificationsLS-HB Specifications Universal Power Supply DimensionsWeight without lens Operating TemperatureLS-HB Dimensions LS-HB DimensionsKHz Supported TimingsComponent CompositePAL-B/G Page 020-1093-00 Rev. a November