Runco LS-HB operation manual Source Enable Sub-Menu

Page 79

Operation

Source Enable: To enable or disable selection of a source, choose Source Enable from the System menu and press ENTER. This displays the Source Enable sub-menu, shown in Figure 4-12.

Figure 4-12. Source Enable Sub-Menu

•HDMI 1/HDMI 2: Enables or disables the HDMI 1 and HDMI 2 sources.

•RGB: Enables or disables the RGB source.

•Comp 1: Enables or disables the Component 1 source.

•Video: Enables or disables the Composite video source.

If either Component 1 or Video is enabled, SCART must be disabled.

Note

•S-Video:Enables or disables the S-Video source.

•SCART: Enables or disables the SCART RGBS source.

If SCART is enabled, both Component 1 and Video must be disabled.

Note

Runco LS-HB Installation/Operation Manual

63

Image 79

Contents LS-HB Page RuncoCare Standard Features RuncoCare Standard Two Year Limited WarrantyRuncoCare Claim Procedure Extended Service Options Copyright and Trademarks Important Safety Instructions Declaration of Conformity Compliance InformationFCC Part Page Table of Contents Operation Specifications Maintenance and TroubleshootingSerial Communications Table of Contents Xiv List of Figures List of Figures About This Manual IntroductionIf you need Turn to Using This ManualDescription, Features and Benefits Optional Accessories LS-HB at a Glance Controls and FunctionsCursor Keys SourceLS-HB Rear/Bottom/Top View Runco Logo Badge RGB LS-HB Rear PanelOFF LS-HB Remote ControlTrigger 1 3.5-mm, mini phono jack RS-232Aspect Ratio Selection Button Memory Preset Buttons M1 / M2 / M3Picture Adjustment Buttons Contrast Sharpness Sharp Press to adjust sharpness Gamma GammaControls and Functions Remote Control InstallationOperation IR Reception Angles Step Procedure Quick SetupFor Details, Refer Installation Type InstallationConsiderations Throw Distance Ambient LightEstimating Throw Distance Lens Screen Lens Only Anamorphic Minimum Maximum Vertical and HorizontalPosition PrimaryFloor Installation Ceiling InstallationLens Shift Folded Optics Anamorphic Lens Installing the Optional Anamorphic Lens MountInstalling the Movable Transport AssemblyAttaching the Transport Assembly Attachment Plate Ceiling Mount Plate Attachment Plate Projector bottom Do not OVER-TIGHTEN the ScrewsPlate Installation Plate Anamorphic Lens BaseDo not use the mounting screws provided with the ceiling Mounting the LS-HB Angle Adjusting the ProjectionConnections to the LS-HB Connector Panel AccessComponents to the LS-HB Connecting SourceHDMI/DVI Connections See Figure Computer RGB Camcorder RGB ConnectionsGaming Console 10. Scart Rgbs ConnectionDTV-Set-Top Box 11. Component Video ConnectionsCamcorder 12. Composite and S-Video ConnectionsConnection RS-232 ControllerTrigger Output to External Connecting 12-VoltTheater Equipment Is appropriate to your locale Connecting an External IRConnecting to AC Power ReceiverZoom Out Focus Zoom Turning on the Power Primary Lens AdjustmentsRear Projection Ceiling Mode Changing the OSD Language Adjusting the Picture OrientationIt is extremely important that the primary lens is properly Installing and Adjusting the Anamorphic LensAdjusting the Lens Height and Angle Correct Lens Angle Incorrect Lens Angle Tighten the knobs Installation Selecting An Input Source OperationSelecting Video Memory Selecting an Aspect RatioPIP Input Source Using Picture-In-Picture PIPUsing the On-Screen Menus LS-HB Main Menu 169 Aspect Ratio SettingsNarrow 169Native You must enter a passcode to access the Save ISF Typical Pluge Pattern for Adjusting Brightness Typical Test Pattern for Adjusting Sharpness Operation Overscan Examples Source Select Sub-Menu LS-HB Advanced Menu Same frame rate as the main source RGB Adjust Sub-Menu 10. Fine Sync Sub-Menu 11. LS-HB System Menu 12. Source Enable Sub-Menu PBP1 PBP2 14. PIP Split-Screen Mode Operation Language 15. LS-HB Service Menu OSD menus are not available when in test pattern mode Operation Lamp Replacement Maintenance and TroubleshootingSymptom Possible Causes Solution Troubleshooting TipsLS-HB Maintenance and Troubleshooting Serial Communications Key CommandsRS232 Remote Button IR Code Description Keyname Set Serial Command Key Names and IR CodesGam.crt Lit.tog Operations Control Commands Function Action on unitOperation Commands Values Serial CommandsSave.isf Resync Execute Color.space = ? Trans.menu = ? Soft.version Error Code LED Indication Description RS-232 Error CodesFan 1 failed Serial Communications LS-HB Specifications SpecificationsLS-HB Specifications Universal Power Supply DimensionsWeight without lens Operating TemperatureLS-HB Dimensions LS-HB DimensionsKHz Supported TimingsComponent CompositePAL-B/G Page 020-1093-00 Rev. a November