Runco LS-HB operation manual Installing the Optional Anamorphic Lens Mount, Installing the Movable

Page 37

Installation

If you are installing a standard LS-HB (without an anamorphic lens), skip this step and proceed with Mounting the LS-HB(page 27).

If you are installing an LS-HB with a fixed anamorphic lens, proceed with Installing the Fixed Anamorphic Lens Base Plate (page 26).

If you are installing an LS-HB with a movable anamorphic lens, proceed as follows to install the lens mount and transport assembly.

3.4

Installing the Optional Anamorphic Lens Mount

Note	1. Do not install the anamorphic lens yet, only the transport
Note	assembly and/or lens mount. You will install the anamorphic lens
	after you install the projector and adjust the primary lens.
	2. Some components shipped with your projector may differ slightly
	from what is shown in these instructions.
Package Contents: The LS-HB movable anamorphic lens mount kit consists of the		Installing the Movable
following items. Some components shipped with your projector may differ slightly from		Anamorphic Lens
what is shown in these instructions. If any items are missing or damaged, please contact		Transport Assembly

your Runco dealer or Runco Customer Service at (800) 23RUNCO.

• Transport Assembly Attachment Plate

• Attachment plate hardware (screws, washers and spacers)

• Attachment plate security hooks and related hardware (chain, chain ends, nuts and washers)

•Transport Assembly

•Transport mounting hardware

•Lens bracket mounting hardware

•Power supply

•Remote control unit and batteries

Runco LS-HB Installation/Operation Manual

21

Image 37

Contents LS-HB Page RuncoCare Standard Features RuncoCare Standard Two Year Limited WarrantyRuncoCare Claim Procedure Extended Service Options Copyright and Trademarks Important Safety Instructions Declaration of Conformity Compliance InformationFCC Part Page Table of Contents Operation Specifications Maintenance and TroubleshootingSerial Communications Table of Contents Xiv List of Figures List of Figures About This Manual IntroductionIf you need Turn to Using This ManualDescription, Features and Benefits Optional Accessories LS-HB at a Glance Controls and FunctionsCursor Keys SourceLS-HB Rear/Bottom/Top View Runco Logo Badge RGB LS-HB Rear PanelTrigger 1 3.5-mm, mini phono jack LS-HB Remote ControlRS-232 OFFPicture Adjustment Buttons Contrast Memory Preset Buttons M1 / M2 / M3Sharpness Sharp Press to adjust sharpness Gamma Gamma Aspect Ratio Selection ButtonControls and Functions Remote Control InstallationOperation IR Reception Angles Step Procedure Quick SetupFor Details, Refer Installation Type InstallationConsiderations Throw Distance Ambient LightEstimating Throw Distance Position Vertical and HorizontalPrimary Lens Screen Lens Only Anamorphic Minimum MaximumFloor Installation Ceiling InstallationLens Shift Folded Optics Installing the Movable Installing the Optional Anamorphic Lens MountTransport Assembly Anamorphic LensAttaching the Transport Assembly Attachment Plate Ceiling Mount Plate Attachment Plate Projector bottom Do not OVER-TIGHTEN the ScrewsPlate Installation Plate Anamorphic Lens BaseDo not use the mounting screws provided with the ceiling Mounting the LS-HB Angle Adjusting the ProjectionConnections to the LS-HB Connector Panel AccessComponents to the LS-HB Connecting SourceHDMI/DVI Connections See Figure Computer RGB Camcorder RGB ConnectionsGaming Console 10. Scart Rgbs ConnectionDTV-Set-Top Box 11. Component Video ConnectionsCamcorder 12. Composite and S-Video ConnectionsConnection RS-232 ControllerTrigger Output to External Connecting 12-VoltTheater Equipment Connecting to AC Power Connecting an External IRReceiver Is appropriate to your localeZoom Out Focus Zoom Turning on the Power Primary Lens AdjustmentsRear Projection Ceiling Mode Changing the OSD Language Adjusting the Picture OrientationIt is extremely important that the primary lens is properly Installing and Adjusting the Anamorphic LensAdjusting the Lens Height and Angle Correct Lens Angle Incorrect Lens Angle Tighten the knobs Installation Selecting Video Memory OperationSelecting an Aspect Ratio Selecting An Input SourcePIP Input Source Using Picture-In-Picture PIPUsing the On-Screen Menus LS-HB Main Menu 169 Aspect Ratio SettingsNarrow 169Native You must enter a passcode to access the Save ISF Typical Pluge Pattern for Adjusting Brightness Typical Test Pattern for Adjusting Sharpness Operation Overscan Examples Source Select Sub-Menu LS-HB Advanced Menu Same frame rate as the main source RGB Adjust Sub-Menu 10. Fine Sync Sub-Menu 11. LS-HB System Menu 12. Source Enable Sub-Menu PBP1 PBP2 14. PIP Split-Screen Mode Operation Language 15. LS-HB Service Menu OSD menus are not available when in test pattern mode Operation Lamp Replacement Maintenance and TroubleshootingSymptom Possible Causes Solution Troubleshooting TipsLS-HB Maintenance and Troubleshooting Serial Communications Key CommandsRS232 Remote Button IR Code Description Keyname Set Serial Command Key Names and IR CodesGam.crt Lit.tog Operations Control Commands Function Action on unitOperation Commands Values Serial CommandsSave.isf Resync Execute Color.space = ? Trans.menu = ? Soft.version Error Code LED Indication Description RS-232 Error CodesFan 1 failed Serial Communications LS-HB Specifications SpecificationsLS-HB Specifications Weight without lens DimensionsOperating Temperature Universal Power SupplyLS-HB Dimensions LS-HB DimensionsComponent Supported TimingsComposite KHzPAL-B/G Page 020-1093-00 Rev. a November