Runco DTV-873 manual IR Transmission Indicator, Sound controls Not used, For Future Use

Page 10

LOCATION AND FUNCTION OF CONTROLS

1

18			17		16

F5

EXIT

F4

F3

F2

F1

ADJ

2

		14			12


15			13				11

ENT

ll

TEXT

- PHASE +

*
PAUSE	?



3			4				6
						5
						5

10

- SHARPN +	- TINT +	- COLOR +	- BRIGHTN +	- CONTR +	BALANCE +	- VOL +
					-
0	8	6	4	2	TREBLE +	- BASS +
9	7	5	3	1	-
9	7	5	3	1




7		8					9

1IR Transmission Indicator

2ADJ. : Adjust key, to enter or exit the adjustment mode.

3Address key (recessed key) : to enter the address of the projec- tor (between 0 and 9). Press the address key, followed by press- ing one digit button between 0 and 9. When addressed to O , the remote will talk to any projector, regardless of its address.

4STBY : Stand by button:

-To initiate remote power up operation

-To stop projection without main power off.

5Pause : To mute the image, press PAUSE. The image disappears but full power is retained for immediate restarting.

6Mute : Not used

7Help : Not used.

8Digit buttons : Direct aspect ratio selection.

9Sound controls : Not used.

10Picture controls : Use these buttons to obtain the desired level (see also ‘Controlling’) for each picture function.

11Phase : Not used.

12Text : When adjusting one of the image controls during a meet- ing, the displayed bar scale can be removed by pressing ‘TEXT’ key first. To re-display the bar scale on the screen, press ‘TEXT’ key again. ‘TEXT’ key is only active in operational mode. When ‘TEXT’ is off, no warning message will be dis

played.

13FREEZ : Not used.

stand-bycolor

pause / park	brightness
sharpness	contrast

tint

14For Future Use

15ENTER : To start up the adjustment mode or to confirm an adjustment or selection in the adjustment mode.

16Control disc : To make menu selections when in the adjustment mode. Also allows to increment or decrement an adjustment in

the adjustment mode.

Control disc up = up arrow in the menus Control disc down = down arrow in the menus

Control disc to the right = arrow to the right on the menus Control disc to the left = arrow to the left on the menus

17EXIT : To leave the adjustment mode or to scroll upwards when in the adjustment mode.

18For Future Use

2-2

Image 10

Contents DTV-873 Page Table of Contents Table of Contents Touch UP and Autoconvergence EYE-Q Diagnostics Safety Instructions Installation InstructionsOn installation Mains lead Power cord with CEE 7 plugPower cord with Ansi 73.11 plug On servicingLocation and Function of Controls Sound controls Not used IR Transmission IndicatorFor Future Use Switching On/Off AC Power mains Cord ConnectionPower Check ConnectionsConnections Video input selectionConnecting an S-Video or Video source to the S-Video input Input selectionRgbs or RGsB input selection Connecting a RGB Analog sourceConnecting a RGB Analog source with Tri-level sync RGB3S or RG3sB input selectionConnecting a Component source with Tri-level sync Connecting a Component sourceYYB-YS or R-YYsB-Y input selection YYB-Y3S or R-YY3sB-Y input selection Remote controlData communications Controlling Controlling Contrast Control Tint ControlBrightness Control Color Saturation ControlStart UP of the Adjustment Mode Adjustment modeCompose Starting up the random access adjustment mode Random Access Adjustment ModeOverview ‘Random Access Adjustment’ mode Selecting Setup Pattern Internal Cross Hatch PatternSync Fast/Slow Adjustment Random access adjustment mode selection menuPicture Tuning Color BalanceColor Select PeakingLine Doubler Color SelectPhase Raster Shift Geometry AdjustmentsHorizontal Phase Adjustment GeometryRaster Shift Adjustment Left-Right east-west Adjustments Left Right E-WTop-Bottom north-south Adjustments TOP Bottom N-SVertical Linearity Adjustment Size AdjustmentLinearity Blanking Adjustments Top blanking Left blanking Right blanking Bottom blankingCoarse Convergence Adjustments Convergence AdjustmentConvergence Fine Convergence Adjustments Vertical cornersStarting up the Service mode Service ModeOverview flowchart ‘Service’ mode Projector SET-UP Projector Set-upIdentification IdentificationTotal Run Time Change passwordChange Language Change baudrate Power up modeChange Projector Address Change Projector AddressMemory Management Memory managementCopy a block Copy a BlockDeletion of all blocks Deletion of blocksDeleting block by block Delete a BlockUndo all settings to midpos All settings to midpositionConvergence mid Green convergence mid Common SettingsUndo R & B convergence mid Undo green convergence midCRT run in cycle G2 AdjustmentG2 Adjustment CRT RUN in Cycle Projector Warm UPProjector warm up Nal # pattern and restart the CRT run in optionExit returns to the Path Selection main menu Enter to select the projector warm up menuI2C Diagnostics 12C DiagnosticsMESSAGES, WARNINGS, and Failures Messages, Warnings, and Failures Specifications Appendix RS 232 ControlSending a Record single instruction Command Code List $02,$00,$00,$51,$0A,$00,$00,$00,$01,$5C Overview AppendixEasy-to-use, high precision automatic convergence system Access to EYE-QTMON-SCREEN Menus EYE-QTMMENUEYE-QTMSETUP Focusing the Camera Lens Centering the Camera Centering the Camera HorizontallyCentering the Camera Vertically TOUCH-UP on Source ON/OFFAdjusting Other Sources TOUCH-UP on TimerReference Source What is Being Measured by EYE-QTM Learning a ReferenceAdjusting Screen Size On Current SourceAlign on Current Source TOUCH-UPAlign from Midposition on Current Source TOUCH-UP on ALL Sources On ALL SourcesAlign on ALL Sources Align from Midposition on ALL Sources Error MessagesInterrupting the Automatic Convergence Process No Pattern Error Status Reporting Forced BreakEYE-QTMDIAGNOSTICS APX-16 Page RUMA-003400 rev