Runco DTV-873 manual Change Projector Address, Change baudrate, Power up mode

Page 37

Service Mode

Change Projector Address

Every projector requires an individual address between 0 and 255. This address can be software installed.

To change that address, push the control disc up or down to highlight ‘Change Pro- jector Address’ and press ENTER. The Change Projector Address menu will be displayed and the actual address will be filled in.

ENTER displays the 'Change Projector Address' menu. EXIT returns to the Service mode main menu.

The first digit is highlighted. Select the individual digits by pushing the control disc to the right or to the left. Reprogram with the digit keys on the RCU.

Press ENTER to confirm.

Press EXIT to return the projector set up menu.

Change baudrate

PROJECTOR SET-UP

IDENTIFICATION

TOTAL RUN TIME

CHANGE PASSWORD

CHANGE LANGUAGE

CHANGE PROJECTOR ADDRESS

PROJECTOR ADDRESS

Enter new projector

 

address :

 

0 0 0

 

Use

and

to select,

and reprogram

with numeric keys.

Highest address is 255

<ENTER> to confirm

<EXIT> to return.

The communication speed between projector and computer has 8 possible speeds. The baud rate speed can be software set up. Highlight ‘Change Baudrate’ by push- ing the control disc up or down and press ENTER to display the Baud rate menu.

The following baud rates are available :

-9600

-4800

-2400

-1200

-600

-300

-150

-110

The actual baud rate will be highlighted. To change the baud rate, push the control disc up or down or to the left or to the right to select the desired baud rate and press ENTER to accept this baud rate.

ENTER to accept the selected baud rate.

EXIT to return without changing the baud rate.

Power up mode

When pressing the power switch, the projector can start up in ‘operating mode’ or in ‘stand-by mode’.

Operating mode : the projector start up and displays image.

Stand-by mode : the projector start up in stand-by and waits until the stand-by but- ton or a digit key is pressed.

To change the Power up mode, select Power Up mode by pushing the control disc up or down and press ENTER to toggle between ‘Operating’ and ‘Standby’.

ENTER to toggle between operating and standby.

EXIT to return to the Service menu.

PROJECTOR SET-UP

IDENTIFICATION

TOTAL RUN TIME

CHANGE PASSWORD

CHANGE LANGUAGE

BAUDRATE

 

Select new

 

baudrate :

 

9600

4800

2400

1200

600

300

150

110

Select with arrow keys:

<ENTER> to confirm

<EXIT> to return.

PROJECTOR SET-UP

IDENTIFICATION

TOTAL RUN TIME

CHANGE PASSWORD

CHANGE LANGUAGE

CHANGE PROJECTOR ADDRESS

CHANGE BAUDRATE

POWER UP MODE: operating

Select with or then <ENTER> <EXIT> to return.

7-4

Page 36 Page 38
Image 37
Page 36 Page 38
Contents DTV-873 Page Table of Contents Table of Contents Touch UP and Autoconvergence EYE-Q Diagnostics Installation Instructions Safety InstructionsPower cord with Ansi 73.11 plug Mains lead Power cord with CEE 7 plugOn installation On servicingLocation and Function of Controls Sound controls Not used IR Transmission IndicatorFor Future Use Power Check AC Power mains Cord ConnectionSwitching On/Off ConnectionsVideo input selection ConnectionsInput selection Connecting an S-Video or Video source to the S-Video inputConnecting a RGB Analog source with Tri-level sync Connecting a RGB Analog sourceRgbs or RGsB input selection RGB3S or RG3sB input selectionConnecting a Component source with Tri-level sync Connecting a Component sourceYYB-YS or R-YYsB-Y input selection YYB-Y3S or R-YY3sB-Y input selection Remote controlData communications Controlling Controlling Brightness Control Tint ControlContrast Control Color Saturation ControlAdjustment mode Start UP of the Adjustment ModeCompose Starting up the random access adjustment mode Random Access Adjustment ModeOverview ‘Random Access Adjustment’ mode Internal Cross Hatch Pattern Selecting Setup PatternPicture Tuning Random access adjustment mode selection menuSync Fast/Slow Adjustment Color BalanceLine Doubler PeakingColor Select Color SelectHorizontal Phase Adjustment Geometry AdjustmentsPhase Raster Shift GeometryRaster Shift Adjustment Left Right E-W Left-Right east-west AdjustmentsTOP Bottom N-S Top-Bottom north-south AdjustmentsVertical Linearity Adjustment Size AdjustmentLinearity Top blanking Left blanking Right blanking Bottom blanking Blanking AdjustmentsCoarse Convergence Adjustments Convergence AdjustmentConvergence Vertical corners Fine Convergence AdjustmentsStarting up the Service mode Service ModeOverview flowchart ‘Service’ mode Identification Projector Set-upProjector SET-UP IdentificationTotal Run Time Change passwordChange Language Change Projector Address Power up modeChange baudrate Change Projector AddressCopy a block Memory managementMemory Management Copy a BlockDeleting block by block Deletion of blocksDeletion of all blocks Delete a BlockUndo all settings to midpos All settings to midpositionConvergence mid Undo R & B convergence mid Common SettingsGreen convergence mid Undo green convergence midG2 Adjustment G2 AdjustmentCRT run in cycle CRT RUN in Cycle Projector Warm UPExit returns to the Path Selection main menu Nal # pattern and restart the CRT run in optionProjector warm up Enter to select the projector warm up menu12C Diagnostics I2C DiagnosticsMESSAGES, WARNINGS, and Failures Messages, Warnings, and Failures Specifications RS 232 Control AppendixSending a Record single instruction Command Code List $02,$00,$00,$51,$0A,$00,$00,$00,$01,$5C Appendix OverviewEasy-to-use, high precision automatic convergence system EYE-QTMMENU Access to EYE-QTMON-SCREEN MenusEYE-QTMSETUP Focusing the Camera Lens Centering the Camera Horizontally Centering the CameraTOUCH-UP on Source ON/OFF Centering the Camera VerticallyAdjusting Other Sources TOUCH-UP on TimerReference Source Learning a Reference What is Being Measured by EYE-QTMOn Current Source Adjusting Screen SizeAlign on Current Source TOUCH-UPAlign from Midposition on Current Source TOUCH-UP on ALL Sources On ALL SourcesAlign on ALL Sources Align from Midposition on ALL Sources Error MessagesInterrupting the Automatic Convergence Process Status Reporting Forced Break No Pattern ErrorEYE-QTMDIAGNOSTICS APX-16 Page RUMA-003400 rev

DTV-873 specifications

The Runco DTV-873 is a premier high-definition projector that epitomizes luxury home theater technology. This state-of-the-art device is designed for audio-visual enthusiasts who demand top-tier performance and uncompromising picture quality. With its stunning 1080p resolution, the DTV-873 delivers images that are remarkably detailed and lifelike, making it an ideal choice for cinematic experiences at home.

One of the standout features of the Runco DTV-873 is its unique imaging technologies. The projector utilizes advanced DLP (Digital Light Processing) technology, which ensures smooth motion reproduction and vibrant color accuracy. The combination of DLP optics and the proprietary Runco color management system results in a vivid and true-to-life color palette. The DTV-873 boasts a contrast ratio of up to 14,000:1, producing deep blacks and brilliant highlights that captivate viewers and enhance the overall viewing experience.

The versatility of the DTV-873 also makes it a remarkable addition to any home theater setup. It supports multiple aspect ratios, including 16:9 and 2.35:1, enabling seamless integration with various screen formats. The built-in lens offset and a wide range of lens options further enhance its adaptability, allowing for effortless installation in diverse room environments.

Furthermore, the DTV-873 features Runco's proprietary Vivix processing system, which enhances the projector's video performance by significantly improving deinterlacing, scaling, and color reproduction. This technology minimizes artifacts and delivers a smoother, more immersive viewing experience. Additionally, the projector is equipped with various connectivity options, including HDMI, component, and RS-232, ensuring compatibility with a wide range of devices and easy integration into existing home entertainment systems.

The design of the DTV-873 emphasizes both aesthetics and functionality. The sleek, elegant casing is both stylish and discreet, making it an attractive addition to any home theater. The user-friendly interface allows for easy adjustments to settings, ensuring that users can quickly optimize the projector for their unique environment.

In conclusion, the Runco DTV-873 is a sophisticated and high-performing projector that combines advanced imaging technologies with elegant design. Its impressive features and capabilities make it a standout choice for anyone looking to elevate their home theater experience. Whether for movie nights, gaming, or presentations, the DTV-873 delivers unparalleled quality and performance that is sure to impress.
Top Page Image Contents